Table of Contents
Advertisement
Note: Only 16-bit or 24-bit, 44.1kHz or 48kHz WAVE files
are supported. Other bit depths and sampling rates are not
supported.
3. Press the SAMPLING START/STOP button or the
on-screen Play button.
The selected WAVE file will play.
4. To stop playback, either press the SAMPLING
START/STOP button again, or touch the on-screen
Stop button.
If the WAVE file is mono, the same sound will be output
to L and R.
Auto Sampling Setup
This command automatically sets various sampling-related
parameters for SAMPLING mode operations. You can use
this command when you want to sample an external audio
source, or when you want to apply an effect to a sample and
resample it. You can also use this command to initialize the
settings.
When you execute this command, the applicable
parameters will be set automatically. You cannot use the
page menu command "Compare" to recall the previous
settings.
The settings are automatically made for the most typical
applications. After executing the auto setup operation,
you can further adjust any of the settings to suit your
needs as described below.
1. Select Auto Sampling Setup to open the dialog box.
2. Use the radio buttons to select the type of settings you
want to make.
Initialize: Initialize the sampling-related parameters to
their default values.
REC Audio Input: Make settings for sampling an
external audio source.
Auto Resample through IFX: Make settings for
applying an effect to a sample and resampling it.
3. Make additional settings as desired, as described
below.
The available settings will depend on whether you've
selected Initialize, REC Audio Input, or Auto Resample
through IFX.
Initialize
If you select Initialize:
1. Press the OK button to initialize the settings, or press
the Cancel button if you decide not to execute. For
more information, please see "Auto Sampling Setup:
SAMPLING: Page Menu Commands Auto Sampling Setup
Automatically-set parameters and their values" on
page 613.
REC Audio Input
If you select REC Audio Input:
1. Use "Source Audio" to select the external audio input
source.
Audio Input 1/2: These are the analog audio inputs, for
either microphones or line-level signals.
USB 1/2: These are the USB audio inputs, for sampling
from a connected computer.
2. Use "Mono-L/Mono-R/Stereo" to select the input
source, and either mono or stereo as the number of
channels that will be sampled.
Mono-L: Settings will be made to sample only the left
input.
Mono-R: Settings will be made to sample only the right
input
Stereo: Settings will be made for sampling in stereo.
3. Use "Save to" to specify the destination to which the
sampled data will be written. RAM writes the data
into SAMPLING mode. DISK creates a Wave file
from the sampled data and saves it to drive.
4. If you want to apply an insert effect to the external
audio input source while it is being sampled, use
"IFX" to specify the insert effect that you want to use.
If you don't want to use an insert effect, set this Off.
5. Press the OK button to execute the REC Audio Input
command, or press the Cancel button if you decide
not to execute.
For more information, please see "Auto Sampling Setup:
Automatically-set parameters and their values" on
page 613.
Note: When you are ready to sample (after executing REC
Audio Input), press the SAMPLING REC button and then
the SAMPLING START/STOP button to begin sampling.
(This is because Trigger is set to Sampling START button.)
When you've finished performing, press the SAMPLING
START/STOP button to stop sampling.
Note: Here's how to check the data you just sampled.
If you specified Save to RAM, play the C2 note of the
keyboard to hear the sample. If you specified Save to DISK,
use the menu command Select Directory/File for Sample to
Disk to hear the sample.
Note: If you specified Save to DISK and want to change the
save-destination for the Wave files, use the menu command
Select Directory/File for Sample to Disk.
Note: If you want to change the way in which sampling is
initiated, change the Trigger setting.
611
Advertisement
Table of Contents
