Table of Contents
Advertisement
Appendices
Controlling pan (stereo position)
Pan (CC#10) [Bn, 0A, vv]
(vv: value, where 00 is far left, 64 is center, and 127 is far
right)
When the above CC# is assigned to the foot pedal or the RT
control knobs 1–6, operating that controller will transmit Pan
messages, and the panning will change. When this message
is received, the result will be the same as when the controller
is operated.
• When you set the Pan (SEQUENCER 0–1b) in
SEQUENCER mode, or when you re-select the song or
return to the beginning of the measure in SEQUENCER
mode, Panpot messages (except for RND) will be
transmitted by each track whose Status is Both, EXT, or
EX2. For more information, see "Pan" on page 447.
Post insert effect pan (CC#08) [Bn, 08, vv]
(vv: value, where 00 is far left, 64 is center, and 127 is far
right)
When the above CC# is assigned to the ASSIGNABLE
PEDAL, as the RT control knobs 1–6, or CC Control,
operating that controller will transmit Post Insert Effect
Panpot messages, and the panning of the sound following the
insert effect will change. When this message is received, the
result will be the same as when the controller is operated.
• In PROGRAM mode and SAMPLING mode, this
message is transmitted/received on the global MIDI
channel. In COMBINATION, and SEQUENCER modes,
this message is transmitted/received on the MIDI channel
specified for each insert effect.
• When you set "Pan (CC#8)" (SEQUENCER 8–5a) in
SEQUENCER mode, or when you re-select the song or
return to the beginning of the measure in SEQUENCER
mode, Post Insert Effect Panpot messages will be
transmitted by each track whose Status is Both, EXT, or
EX2. For more information, see "8–5a: IFX" on
page 513.
Controlling effects
Effect Control 1 (CC#12) [Bn, 0C, vv]
Effect Control 2 (CC#13) [Bn, 0D, vv]
These CCs are used for effects dynamic modulation (Dmod),
and can be programmed to control various effects
parameters. Note that other CCs can also be used as Dmod
sources, if desired.
Effect control 1 and 2 can be assigned to the ASSIGNABLE
PEDAL, RT control knobs 1–6, or CC Control.
Effect 1 depth (Send 2) (CC#91) [Bn, 5B, vv]
Effect 3 depth (Send 1) (CC#93) [Bn, 5D, vv]
These CCs control the per-Osc/Timbre/Track and post-IFX
send levels for Master Effects 1 and 2. In COMBINATION
and SEQUENCER modes, the channel used to control post-
IFX send levels is the channel of the Timbres/Tracks routed
through the IFX, instead of the effect's Control Channel.
These CCs can be assigned to the ASSIGNABLE PEDAL,
RT control knobs 1–6, or CC Control.
• In COMBINATION and SEQUENCER modes, the
actual send level of the timbre/track is determined by
multiplying this value with the Program's per-Oscillator
932
Send 1/2 settings. For more information, see "OSC1
Send1 (to MFX1)" on page 99.
• In SEQUENCER mode, when you adjust Send 1
(MFX1) or Send 2 (MFX2), or when you re-select a
song or return to the beginning of the measure, Send 1/2
will be transmitted by each track whose Status is Both,
EXT, or EX2.
Effect 2 depth (IFX1–12 on/off) (CC#92) [Bn, 5C,
vv]
Effect 4 depth (MFX1, 2 on/off) (CC#94) [Bn, 5E,
vv]
Effect 5 depth (TFX1, 2 on/off) (CC#95) [Bn, 5F, vv]
Separately from the effect on/off settings in each mode, the
Effect Global SW allows you to turn off insert effects
IFX1–12 and master effects MFX1, 2 and total effect TFX1,
2 (see "0–1b: Effect Global SW" on page 633).
If you check IFX1–12 Off, MFX1&2 Off or TFX1&2 Off,
the corresponding message will be transmitted with vv=0
[00]. If you uncheck these settings, the corresponding
message will be transmitted with vv=127 [7F]. If you check
these settings, the corresponding effect(s) will be turned off
as a group. If you uncheck these settings, the on/off settings
of each mode will be used. The same applies to reception.
(vv of 00 is off, and 01 or greater is the original setting.)
These messages are transmitted and received on the global
MIDI channel.
Note: These messages are defined simply for use in
adjusting the effect levels, and may not have the same
function on another instrument connected to the
NAUTILUS.
Using various controllers
Here we will explain typical ways to use the various
controllers.
Foot controller (CC#04) [Bn, 04, vv]
If the above CC# is assigned as the ASSIGNABLE PEDAL
function, this message will be transmitted when the
controller is operated.
• In COMBINATION and SEQUENCER modes, you can
use the MIDI Filters to enable and disable
transmission/reception of this message for each
timbre/track. For more information, see "Enable Foot
Pedal" on page 416.
Advertisement
Table of Contents
