Table of Contents
Advertisement
RPN CC#100=0 (Pitch Bend Range)
CC#06
Bend range, Semitones
00
0
01
+1
...
...
12
+12
RPN CC#100=1 (Fine Tune)
CC#06
CC#38
Tuning, 1 cent steps
32
00
...
...
48
00
...
...
64
00
64
127
...
...
96
00
RPN CC#100=2 (Coarse Tune)
CC#06
Tuning, semitones
40
-24
...
...
52
-12
...
...
64
0
...
...
88
+24
For example, if in SEQUENCER mode you wish to set a
MIDI track on channel 1 to a transpose (coarse tuning) value
of –12, you would first transmit [B0, 64, 02] (64H=CC#100)
and [B0, 65, 00] (65H=CC#101) to the NAUTILUS to select
the RPN coarse tune. Then you would set this to –12 by
transmitting [B0, 06, 34] (06H=CC#6), 34H=52
(corresponds to –12), and [B0, 26, 00] (26H=CC#38,
00H=0).
*3 Volume and Expression
The volume of the NAUTILUS is determined by multiplying
Volume (CC#07) with Expression (CC#11). In
SEQUENCER mode when you stop the song playback and
return the location to the beginning of the track, the Volume
will be set to the starting value, and the Expression will be
set to the maximum value (127).
*4 CCs 70...79
A value of 64 will correspond to the value specified by the
program parameter. 0 is the minimum, and 127 is the
maximum. Changing from 63–1 or from 65–126 will adjust
the effect from the program parameter setting toward the
minimum value or maximum value.
For details about the specific parameters controlled by these
CCs, please see "Parameters controlled by MIDI CCs #70-
79" on page 924.
NAUTILUS and MIDI CCs Responses to standard MIDI controllers
-50
...
-25
...
0
~+1.5
...
+50
*5 Effect Depths 2, 4, and 5
These CCs are recognized only on the global MIDI channel.
*6
VALUE slider and CC#18
Most of the time, the
VALUE slider
values. You can also use the
source, but only when the following are true:
• You're on the PROGRAM > Home page, and the big
Program name is selected, or
• You're on the COMBINATION > Home– Prog
Select/Mixer page, and the big Combination name is
selected, or
• You're on the SET LIST > Home page.
In these cases only, the
VALUE slider
and can be used as a modulation source.
*7 CC assignments for ARP and Pads
As shipped from the factory, for simplicity, all ARP and Pad
CC assignments are set to Off. However, the NAUTILUS
has a set of recommended CC assignments, as shown in the
table above. These assignments can be loaded in a single
step by using the Reset Controller MIDI Assign menu
command on the GLOBAL > Controllers/Scales page. For
more information, see "Reset Controller MIDI Assign" on
page 690.
*8 X-Y Control and MIDI CCs
By default, the X-Y Control X-axis and Y-axis are assigned
to CCs
118
and 119, as shown in the table above. These can
be changed if desired.
The Global MIDI X-Y MIDI Out parameter also affects
MIDI transmission from the X-Y Control and X-Y
Envelope. For more information, see "Vector and MIDI" on
page 41 and "X-Y MIDI Out" on page 651.
is used only for entering
VALUE slider
as a modulation
sends
MIDI
CC#18,
923
Advertisement
Table of Contents
