Table of Contents
Advertisement
MEDIA mode
6. Specify the file system.
FAT16 can format a maximum of 4 Gigabytes. If you are
using media larger than this., use FAT32 format instead.
(FAT32's the theoretical maximum is 2 Terabytes, or
2,000 Gigabytes.)
7. To format the media, press the OK button. To cancel
without formatting, press the Cancel button.
Note: If you want to use a CD-R/RW for writing packet
data, you must format it. If you will be using it as an
audio CD, formatting is not necessary.
Convert to ISO9660 Format
This command converts UDF format CD-R media to
ISO9660 format.
If a file that was saved by the NAUTILUS to CD-R is to be
loaded by another device, you must execute this command to
convert it to ISO9660 format.
This conversion temporarily uses memory space on the
drive.
1. Select "Convert to ISO9660 Format" to open the
dialog box.
2. Press the OK button to execute the conversion, or
press the Cancel button to cancel without executing.
Even if data is converted into ISO9660 format, some files
may not be readable by certain devices.
Rate Convert
This command converts the sampling rate (frequency) of the
selected WAVE file from 48 kHz to 44.1 kHz or 44.1 kHz to
48 kHz.
This is valid only when a 48 kHz or 44.1 kHz WAVE file is
selected.
1. Select the file or directory whose sampling rate
(frequency) you want to convert.
2. Select "Rate Convert" to open the dialog box.
"Rate Convert" will indicate the name of the selected file.
3. Use the Open button and Up button to select the save-
destination directory.
If you want to specify another USB device, use "Drive
Select" to specify it.
726
4. If you want to change the filename for saving, press
the text edit button in the lower line to open the text
edit dialog box, and set the name as desired.
If a USB QWERTY keyboard (commercially available) is
connected, you can use this to enter text instead of the on-
screen keyboard. For more information, see "Editing
names and entering text" on page 202 of the OG.
5. Press the OK button to execute the Rate Convert
command, or press the Cancel button to cancel
without executing.
Check Medium
This command checks the selected storage media for errors,
and corrects any errors if possible. Use Check Medium if
you frequently experience messages such as "Error in
writing to medium" while saving files, or "Buffer overrun
error occurred" while sampling to disk.
1. Use "Drive Select" to select the media that you want to
check.
2. Select "Check Medium" to open the dialog box.
The dialog includes a rough estimate of the time required
to complete the process for the selected media. The actual
time required will vary depending on the speed and
capacity of the media, as well as the number of errors that
are found.
3. Press the OK button to start checking the media, or
press the Cancel button to cancel.
4. When process has been completed, the recovered
content will be displayed.
Note: If you want to stop the checking process before it
has been completed, press the Abort button.
Install EXs
This command installs the selected EXs data onto the
internal SSD, along with any associated files (.KSC, .PCG,
.SNG etc). Note that EXs can only be installed onto the
internal SSD, and not to USB storage media.
To install an EXs:
1. If you downloaded the EXs data, un-zip the
downloaded file.
Un-zipping the archive will result in a folder containing
several different files.
Note: Depending on your browser settings, the downloaded
file may be unzipped automatically. One of the files in the
resulting folder has a name which ends with "tar.gz." Please
do not un-zip this tar.gz file.
2. Copy the un-zipped folder to a USB storage device.
3. Safely disconnect the USB storage device from your
computer.
4. Connect the USB storage device to the NAUTILUS.
Advertisement
Table of Contents
