Table of Contents
Advertisement
Exclusive Solo
This command is available on every page in PROGRAM
mode.
The function of the Solo button will switch each time you
select "Exclusive Solo".
The Solo function operates in two different ways, as shown
below.
• Cleared: Multiple Solo
Solo is turned on for the OSC1 (EXi1), OSC2 (EXi2),
the drum track and AUDIO IN. When the SW1 or SW2
button is set to switch SOLO on/off, Solo will be turned
on or off with each press of the button.
• Selected: Exclusive Solo
Solo will be turned on for only one button.
Note: The solo operation settings for the SW1 or SW2
button are adjusted on the Controllers: Switch page in each
mode.
Note: The Solo function will work on the following
components in each mode. All of the components will be
handled as a single group. When Solo is turned on for even
one component when Exclusive Solo is on, the other
components will turn off.
Program:
OSC1 (EXi1), OSC2 (EXi2), Drum Track, Audio Input1,
Audio Input2, USB 1, USB 2
Combination:
Timbre1...Timbre16, Audio Input1, Audio Input2, USB 1,
USB 2
Sequencer:
MIDI Track1...MIDI Track16,
Audio Track1...Audio Track16,
Audio Input1, Audio Input2, USB 1, USB 2
Sampling:
OSC, Audio Input1, Audio Input2, USB 1, USB 2
Show MS/WS/DKit Graphics
This works in conjunction with the PROGRAM > Basic
page's Play Page MS/WS/DKit Display parameters to
control whether the PROGRAM > Home page shows the
overview/jump parameters, or the selected graphics.
It only applies if a graphic has been selected for Play Page
MS/WS/DKit Display Osc 1 or Osc 2. If these parameters
are instead set to Show MS/WS/DK Names, the menu
command has no effect. For more information, see "1–1h:
Play Page MS/WS/DKit Display" on page 40.
This mirrors the Global parameter "Show MS/WS/DKit
Graphics" on page 635. Changes to the menu are reflected in
the Global parameter, and vice-versa. To save this setting,
use the Write Global Setting command in GLOBAL mode.
PROGRAM: Page Menu Commands Exclusive Solo
Add To Set List
This command, available on the Home pages of
PROGRAM, COMBINATION, and SEQUENCER modes,
allows the addition of the current Program, Combination, or
Song to a Set List.
1. Choose "Add to Set List" to open the dialog box.
2. Use the "Set List" and "Insert Slot" parameters to
select the destination Set List and Slot.
By default, these are set to the current Set List and Slot. If
you select something other than the current Set List and Slot,
the Revert to Current button will be enabled; press this
button to return the parameters to the current Set List and
Slot.
3. Use the text popup to set the Slot Name as desired.
The name of the Program, Combination, or Song is copied
into the slot name by default.
4. Press OK to add the Program, Combination, or Song
to the Set List, or press Cancel to exit without making
changes.
When you press OK, the current Program, Combination, or
Song is inserted at the selected Slot, using the same logic as
the Set List Edit page's Insert command.
When adding a Song, the current Keyboard Track is copied
into the slot's Keyboard Track parameter.
Initialize Program
Initialize Program is available on the PROGRAM > Home
page. This command restores all Program settings to their
defaults, so that you can start with a clean slate. Note that
any edits you've made to the Program will be lost.
You can either initialize the current Program only, or all
Programs in the current bank.
To initialize only the current Program:
1. Select the "Initialize Program" menu command.
The Initialize Program dialog box will appear.
By default, the All Programs in the current bank check-
box will be disabled (un-checked). Leave it that way.
113
Advertisement
Table of Contents
