Table of Contents
Advertisement
1–1c: MIDI Filter
Enable Program Change
On (checked): Program changes will be transmitted and
received.
In PROGRAM mode (PROGRAM P0: Play), the program
will be switched when a program change message is
received on the global MIDI channel specified by MIDI
Channel (1–1a). When you switch programs, a program
change message will be transmitted on the global MIDI
channel.
In COMBINATION mode (COMBINATION P0: Play), the
combination will be switched when a program change
message is received on the global MIDI channel. However, it
is possible to set the "Enable Combination Change"
parameter so that the combination is not switched. When a
program change is received on the channel specified for each
timbre by MIDI Channel (COMBINATION 2–1a), the
program of that timbre will be switched. However, the
program changes for each timbre will be affected by the
setting of the "Enable Program Change" parameter
(COMBINATION 3–1a).
When you switch combinations, a program change message
will be transmitted on the global MIDI channel, and also
transmitted simultaneously on the channel of timbres whose
Status (COMBINATION 0–1b, 2–1a) is set to EXT or EX2.
In SEQUENCER mode, incoming program change
messages on a channel that corresponds to a track whose
Status (SEQUENCER 2–1a) is set to INT or Both will
switch programs on that track. When you select a song or
playback sequencer data, program changes will be
transmitted on the channels of tracks whose Status is set to
Both, EXT, or EX2.
In SET LIST mode (Home), the slot will be switched when a
program change message is received on the global MIDI
channel. When you switch slots, a program change message
will be transmitted on the global MIDI channel. If the Slot
contains a Combination or Song, other program change
messages may be transmitted on additional MIDI channels,
as would normally occur in COMBINATION or
SEQUENCER modes.
Off (unchecked): Program changes will not be transmitted
or received.
Bank Change
On (checked): The Bank Select control change message
will be transmitted together with program change messages.
This is valid when "Enable Program Change" is checked.
Off (unchecked): Bank Select messages will not be
transmitted or received.
When recording on the internal sequencer, bank select
messages will be recorded regardless of this setting.
However for playback, this setting will apply.
This also controls send and receive of Bank Select messages
for Set List selection in SET LIST mode.
Combination Change
On (checked): When in COMBINATION P0: Play, an
incoming program change message on the global MIDI
channel set by MIDI Channel (1–1a) will switch
Combinations.
This is valid when "Enable Program Change" is checked.
An incoming program change on a channel other than the
global MIDI channel will switch the program of any timbre
that matches that MIDI channel.
[Off, On]
Off (unchecked): An incoming program change message on
the global MIDI channel will switch the program of any
timbre whose MIDI Channel (COMBINATION 2–1a)
matches the global MIDI channel. The combination will not
be switched.
The program changes for each timbre will be affected by the
setting of the "Enable Program Change" parameter
(COMBINATION 3–1a).
Enable After Touch
On (checked): MIDI aftertouch messages will be received.
Off (unchecked): MIDI aftertouch messages will not be
received.
Enable Control Change
On (checked): Control change messages will be transmitted
and received.
Off (unchecked): Control change messages will neither be
transmitted nor received.
This setting has no effect when you use the internal
sequencer to playback sequence data that was recorded with
control change data; i.e., the control changes previously
recorded into the sequencer will be transmitted via MIDI.
Enable Exclusive
On (checked): System exclusive data will be transmitted
and received.
Check this if you want to edit the NAUTILUS from a
connected computer, or if you want to allow bi-directional
editing.
Off (unchecked): System exclusive data will not be
transmitted. Normally you will leave this unchecked.
Note: The "Dump" menu commands ("Dump Program"–
"Dump Arpeggio Pattern") will continue to function
regardless of this setting.
1–1d: SEQ MIDI Out Setup
Song Track
This setting specifies what will be transmitted via MIDI
[Off, On]
when you switch songs in SEQUENCER mode.
for Master: When you switch songs in SEQUENCER
mode, tracks whose Status is EXT or Both will transmit
MIDI messages* such as program changes to set-up an
external MIDI sound module.
for External Seq: Choose this option if you're using
SEQUENCER mode as an external multi-timbral sound
module. When you switch songs on the NAUTILUS, no
track whose Status is set to EXT or Both (i.e., any setting
other than INT) will transmit MIDI messages* such as
program changes. This prevents echo-back from the tracks
of your external MIDI sequencer from overwriting the
[Off, On]
program and other parameters of tracks that are set to the
same MIDI channel.
* Applicable MIDI messages and corresponding parameters:
• Program Select: CC#00 bank select (LSB), CC#32 bank
select (MSB), program change
GLOBAL > MIDI 1–1: MIDI
[Off, On]
[Off, On]
[Off, On]
[for Master,
for External Seq]
653
Advertisement
Table of Contents
