Rt Control Knobs 1-6 Assignments - Korg NAUTILUS Series Parameter Manual

Appendices
RT Control Knobs 1–6 Assignments
The RT control knobs 1–6 can be set to control the following
functions when the SELECT button on the front panel is set
to "USER".
Configure these settings on the "Controller" page for each
mode.
• PROGRAM > Basic/X-Y/Controllers– Controllers page
• COMBINATION > EQ/X-Y/Controllers– Controllers
page
• SEQUENCER > EQ/X-Y/Controllers– Controllers page
Note: In PROGRAM, COMBINATION and SEQUENCER
modes, configure the settings for each Program,
Combination and song.
Knobs and MIDI CCs
Some of the assignments include MIDI CCs, which are
transmitted whenever the knob is moved. Note that the MIDI
CCs can still be received even if they are not assigned to a
physical controller.
List of RT Control Knobs assignments
The following functions can be assigned to RT control knobs
1–6.
Off
This setting disables the knob.
Knob Mod. 5–6 (CC#s 20, 21)
These settings let you use the knob as an AMS or Dmod
source. Note that you'll also need to assign the knob to
control the desired parameter within the Program or Effect.
Master Volume
This controls the volume of the main stereo outputs, after the
Total Effects. It does not affect Individual Outputs 1–4.
This also transmits the Universal System Exclusive Master
Volume message [F0H, 7FH, nn, 04, 01, vv, mm, F7H].
Portamento Time (CC#05)
This controls the portamento time. Note that a different
controller, CC#65, turns Portamento on and off; see
"Portamento SW (CC#65)" on page 913.
Volume (CC#07)
Controls the volume, and transmits CC#7.
Post IFX Pan (CC#08)
Controls the panning after the last Insert Effect in the chain,
and transmits CC#8.
Pan (CC#10)
Controls stereo pan, and transmits CC#10.
Expression (CC#11)
Expression is a secondary volume control, which you can
use to scale level without affecting the main volume settings
or CC#7 values.
When used one at a time, MIDI Volume and Expression
affect level in exactly the same way: a MIDI value of 127 is
equal to Program's main Level setting, and lower values
reduce the volume.
914
If both CC#7 and CC#11 are used simultaneously, the one
with the lower value determines the maximum volume, and
the one with the higher value scales down from that
maximum.
FX Control 1 & 2 (CC#s12 & 13)
These assignments are intended for Effect Dynamic
Modulation (Dmod). Note that you'll also need to assign FX
Control 1 or 2 to control the desired parameter within the
Effect.
LFP Cutoff (CC#74)
This scales the cutoff frequency of all of the filters at once.
For instance, in the HD-1, it affects both Filters A and B.
Resonance (CC#71)
This scales the resonance of all of the filters at once. For
instance, in the HD-1, it affects both Filters A and B.
Filter EG Int. (CC#79)
This scales the effect of the Filter EG on the cutoff
frequency. It affects all of the filters at once; for instance, in
the HD-1, it affects both Filters A and B.
F/A Attack (CC#73)
This scales the attack times of the Filter and Amp EGs, along
with other related parameters.
When the CC value is above 64, this also affects the Amp
EG's Start and Attack Levels, Start Level AMS, and Attack
Time AMS, as described below:
Between values of 65 and 80, the Start Level, Start Level
AMS, and Attack Time AMS will change from their
programmed values to 0. Over the same range, the Attack
Level will change from its programmed value to 99.
F/A Decay (CC#75)
This scales the decay and slope times of the Filter and Amp
EGs.
F/A Sustain (CC#70)
This scales the sustain levels of the Filter and Amp EGs.
F/A Release (CC#72)
This scales the release times of the Filter and Amp EGs.
Pitch LFO1 Spd (CC#76)
This scales LFO1's frequency.
Pitch LFO1 Dep (CC#77)
This scales the effect of LFO1 on the Pitch.
Pitch LFO1 Dly (CC#78)
This scales LFO1's fade-in time.
SW 1 Mod. & SW 2 Mod (CC#s 80 & 81)
Normally, these are used for the two assignable switches -
but you can assign them to the knobs instead, if you like.
Foot Switch (CC#82)
You can use this general-purpose controller as an AMS or
Dmod source. Note that you'll also need to assign Foot
Switch (CC#82) to control the desired parameter within the
Program or Effect.