HEIDENHAIN 548431-05 User Manual page 718

Index
A
Absolute coordinates................. 53
Additive compensation............. 153
cycle programming.............. 180
Alphabetic keyboard................... 66
Angle of infeed......................... 315
API thread................................ 324
API threads
recut..................................... 332
Automatic job........................... 150
Axial thread milling................... 357
Axis designations....................... 52
B
Blank
bar/tube................................ 181
Block scan................................ 145
C
Calculating fits.......................... 429
Calculating internal threads...... 429
Calculation of contour geometry –
ICP........................................... 418
Calculator................................... 67
Calibrating the tool touch
probe........................................ 126
C axis......................................... 44
Chamfer................................... 192
Character set............................ 395
Circular drilling pattern
axial...................................... 404
radial.................................... 406
Circular machining.................... 190
Circular milling pattern
axial...................................... 407
radial.................................... 409
Code number........................... 605
Comparing tool lists................. 143
Compatibility in DIN programs. 696
Compensation.......................... 152
Connection possibilities........... 648
Context-sensitive help................ 76
Contour follow-up
during Teach-in..................... 174
Contour group.......................... 528
Control screen............................ 62
Conversion into DIN format...... 168
Converting cycle programs....... 671
Converting DIN programs......... 672
Coordinate system..................... 53
Cut longitudinal........................ 199
Expanded............................. 203
Cut off...................................... 308
Cutting
longitudinal plunge............... 215
transverse plunge................ 217
718
transverse plunge, Expanded....
221
Cutting, longitudinal
finishing plunge.................... 223
finishing plunge, Expanded.. 227
ICP....................................... 241
ICP contour-parallel.............. 231
ICP contour-parallel, finishing....
237
ICP finishing......................... 245
Cutting, longitudinal plunge
Expanded............................. 219
Cutting, transverse
finishing plunge.................... 225
finishing plunge, Expanded. 229
ICP...................................... 243
ICP contour-parallel.............. 234
ICP contour-parallel, finishing....
239
ICP finishing....................... 247
Cutting limits SX, SZ................ 180
Cut transverse.......................... 201
Expanded............................. 205
Cycle
addresses used.................... 180
Comment............................. 175
keys...................................... 174
State.................................... 106
Cycle programming
drilling and milling patterns.. 398
Drilling cycles....................... 342
Cycle starting point.................. 172
D
Data backup.......................
Data input.................................. 65
Deep-hole drilling
axial...................................... 347
radial.................................... 350
Defining offsets........................ 122
Defining the tool change
position.................................... 124
Defining the workpiece datum. 121
Diagnostic bits......................... 570
Displaying operating times....... 127
Drilling
axial...................................... 342
radial.................................... 345
Drilling and milling patterns...... 398
Drilling cycles........................... 342
Driven tools.............................. 118
Dry run mode........................... 154
Duplicating
circular series....................... 436
linear series......................... 435
mirroring.............................. 437
DXF contours........................... 527
E
Editing multipoint tools............ 567
Editing the magazine list.......... 115
Editing the turret list................ 113
EnDat encoders......................... 93
Engraving, character set........... 395
Error log..................................... 74
Error message............................ 71
Ethernet interface.................... 645
(for software 548328- xx)..... 646
(for software 548431-05)...... 648
Example
drilling cycles....................... 359
milling cycles....................... 390
pattern machining................ 410
recessing cycles.................. 310
Thread and undercut cycles. 340
Turning cycles...................... 249
F
Feed rate.................................. 106
File organization....................... 164
Finishing cut
longitudinal........................... 207
longitudinal Expanded.......... 211
transverse............................ 209
transverse, Expanded.......... 213
Full-surface machining................ 45
G
Gestures..................................... 85
H
Handwheel operation............... 139
49, 644
Help graphics........................... 173
Help system............................... 76
I
ICP angle input......................... 430
ICP calculation of contour
geometry.................................. 418
ICP centric polygon
XY plane............................... 509
YZ plane............................... 525
ICP chamfer
front face............................. 464
in turning contour................. 453
lateral surface...................... 470
XY plane............................... 499
YZ plane............................... 515
ICP circle
front face............................. 477
lateral surface...................... 487
XY plane............................... 500
YZ plane............................... 516
ICP circular arc
front face............................. 463
in turning contour................. 452
HEIDENHAIN | MANUALplus 620 | User's Manual | 12/2017
Index