H: Terminal Functions; H: Terminal Functions; H1: Multi-Function Digital Inputs - YASKAWA CIMR-VU BA0001 Technical Manual

5.7 H: Terminal Functions

5.7

H: Terminal Functions

H parameters are used to assign functions to the external terminals.
u

H1: Multi-Function Digital Inputs

n H1-01 to H1-07: Functions for Terminals S1 to S7
These parameters assign functions to the multi-function digital inputs. Settings 0 to 9F determine function for each terminal
and are explained below.
Note: 1. Terminals that are not used and terminals using the through-mode should be set to "F".
2. Drive software versions PRG: 1013 and later require that the Forward run and Reverse Run commands be set simultaneously.
No. Parameter Name
H1-01 Digital Input S1 Function Selection
H1-02 Digital Input S2 Function Selection
H1-03 Digital Input S3 Function Selection
H1-04 Digital Input S4 Function Selection
H1-05 Digital Input S5 Function Selection
H1-06 Digital Input S6 Function Selection
H1-07 Digital Input S7 Function Selection
<1> Number appearing in parenthesis is the default value after performing a 3-Wire initialization.
Setting
0 3-Wire Sequence
1 LOCAL/REMOTE Selection
2 External Reference 1/2
3 Multi-Step Speed Reference 1
4 Multi-Step Speed Reference 2
5 Multi-Step Speed Reference 3
6 Jog Reference Selection
7 Accel/Decel Time 1
8 Baseblock Command (N.O.)
9 Baseblock Command (N.C.)
A Accel/Decel Ramp Hold
B Drive Overheat Alarm (oH2)
C Terminal A1/A2 Enable/Disable
F Not used/Through Mode
10 Up Command
11 Down Command
12 Forward Jog
13 Reverse Jog
14 Fault Reset
15 Fast-Stop (N.O.)
16 Motor 2 Selection
17 Fast-stop (N.C.)
18 Timer Function Input
19 PID Disable
1A Accel/Decel Time Selection 2
1B Program Lockout
1E Reference Sample Hold
20 to 2F External Fault
184
Table 5.26 Digital Multi-Function Input Settings
Function
Setting
Range
1 to 9F 40: Forward Run Command (2-wire sequence)
1 to 9F 41: Reverse Run Command (2-wire sequence)
0 to 9F 24: External Fault (N.O., always detected, coast to stop)
0 to 9F 14: Fault Reset
<1>
0 to 9F
3 (0) : Multi-Step Speed Reference 1
<1>
0 to 9F
4 (3) : Multi-Step Speed Reference 2
<1>
0 to 9F
6 (4) : Jog Reference Selection
Page Setting
185 30 PID Integral Reset
185 31 PID Integral Hold
186 32 Multi-Step Speed Reference 4
34 PID Soft Starter Cancel
186 35 PID Input Level Selection
40 Forward Run/Stop (2-wire sequence)
186 41 Reverse Run/Stop (2-wire sequence)
186 42 Run/Stop (2-Wire sequence 2)
43 FWD/REV (2-Wire sequence 2)
186
44 Offset Frequency 1 Addition
186 45 Offset Frequency 2 Addition
187 46 Offset Frequency 3 Addition
187
<1>
Node Setup
47
187
60 DC Injection Braking Command
61 External Speed Search Command 1
187
62 External Speed Search Command 2
65 KEB Ride-Thru 1 (N.C.)
188
66 KEB Ride-Thru 1 (N.O.)
188
67 Communications Test Mode
188
68 High-Slip Braking
189
6A Drive Enable
188
75 Up 2 Command
189
76 Down 2 Command
189
7A KEB Ride-Thru 2 (N.C.)
189
7B KEB Ride-Thru 2 (N.O.)
189
7C Short-Circuit Braking (N.O.)
190
7D Short-Circuit Braking (N.C.)
190
YASKAWA ELECTRIC SIEP C710606 18F YASKAWA AC Drive – V1000 Technical Manual
Default
Function Page
191
191
191
191
191
191
191
192
192
192
192
192
192
192
192
193
194
194