EWM PHOENIX 301 EXPERT forceArc Operating Instructions Manual page 6

Contents
For your safety
5.5.2
5.5.3
5.5.4
5.5.5
5.5.6
5.6 Key switch ....................................................................................................................................82
5.7 Operating time counter.................................................................................................................82
5.8 Remote control.............................................................................................................................83
5.8.1
5.8.2
5.8.3
5.9 Advanced functions on the welding machine control...................................................................85
5.9.1
5.9.2
5.9.3
5.9.4
5.9.5
5.10 Advanced functions on the wire feed unit control ........................................................................90
5.10.1
6 Commissioning.....................................................................................................................................96
6.1 General.........................................................................................................................................96
6.2 Area of application - proper usage ..............................................................................................96
6.3 Installation ....................................................................................................................................96
6.4 Mains connection .........................................................................................................................96
6.5 Machine cooling ...........................................................................................................................97
6.6 Adding coolant .............................................................................................................................97
6.6.1
6.7 Workpiece lead, general ..............................................................................................................98
6.8 MIG/MAG welding ........................................................................................................................99
6.8.1
6.8.2
6.8.3
6.8.4
6
RINT X11 robot interface ..............................................................................................81
BUSINT X10 Industrial bus interface............................................................................81
DVINT X11 Wire feed interface ....................................................................................81
PC Interfaces ................................................................................................................81
Setting options, internal ................................................................................................81
5.5.6.1 Switching between Push/Pull and intermediate drive ...................................81
R10 manual remote control ..........................................................................................83
Manual remote control R20 ..........................................................................................84
R40 manual remote control ..........................................................................................84
Displaying JOB information ..........................................................................................85
Organising JOBs...........................................................................................................85
5.9.2.1 Creating a new JOB in the memory or copying a JOB .................................86
5.9.2.2 Loading special jobs (SP1 to SP3)................................................................86
5.9.2.3 Loading an existing JOB from the free memory............................................86
5.9.2.4 Using Block mode (Block JOB) .....................................................................87
5.9.2.5 Resetting an existing JOB to the factory setting (Reset JOB) ......................87
Switching the Hold function on and off .........................................................................88
WF speed switching (absolute / relative)......................................................................88
Resetting JOBs to status on delivery (Reset ALL) .......................................................89
Special parameter, "M3.70/M3.71" ...............................................................................90
5.10.1.1 Special parameters list ................................................................................90
5.10.1.2 Selecting, changing and saving parameters ...............................................91
5.10.1.3 Reset to factory settings..............................................................................91
5.10.1.4 Ramp time for wire inching (P1)..................................................................91
5.10.1.5 Program "0", releasing the program block (P2)...........................................91
5.10.1.6 Display mode torch power control (P3) .......................................................91
5.10.1.7 Program limit (P4) .......................................................................................91
5.10.1.8 Special cycle in the operating modes special latched and non-latched
(P5) 92
5.10.1.9 Enabling special JOBs SP1 to SP3 (P6).....................................................92
5.10.1.10 Correction operation, threshold value setting (P7)....................................92
5.10.1.11 Program changeover with standard torch (P8) .........................................93
5.10.1.12 N cycle setting ...........................................................................................95
5.10.1.13 Latched/special-latched tap start (P9).......................................................95
5.10.1.14 "Single or dual operation" (P10) setting ....................................................95
5.10.1.15 Latched special tapping time setting (P11) ...............................................95
5.10.1.16 Software key switch (SCH) .......................................................................95
List of coolants..............................................................................................................98
Intermediate tube package connection.......................................................................100
6.8.1.1 Welding machine.........................................................................................100
6.8.1.2 Wire feed unit ..............................................................................................101
Welding torch connection ...........................................................................................102
Connection for workpiece lead ...................................................................................103
Fixing of the pin reel (adjustment of the pre-tensioning) ............................................104
Item No.: 099-004833-EWM01