Table of Contents
Advertisement
Command and Response Table for IP SIS Commands
ASCII (Telnet)
Command
(Host to Processor)
Bi-directional Serial Data Port
Send data string
E X10!
Example:
E
05 * 4 * 7 * 3L RS
NOTES:
•
X10!
=
Port number (01-99)
•
X10(
=
Time in tens of milliseconds that the WindoWall Pro will wait until receipt of the first response character
before terminating the command. Default = 10 = 10 ms. Max. = 32767.
•
X11)
=
Time in tens of milliseconds that the WindoWall Pro will wait between characters being received via a serial
port before terminating the current command or receive operation. Default = 20 = 20 ms. Max. = 32767.
•
X11!
=
Message length #L or #D. The letter parameter is case sensitive (requires capital D or capital L).
L = Length of the message to be received.
D = Delimiter value. A delimiter of ASCII 0A = 10D.
# = Byte count (for L) or a single ASCII character expressed in decimal form (for D).
The byte count # can be 0-32767. Default = 0.
The ASCII decimal # can be 0-00255. Default = the byte count.
A 3-byte length = 3L. The response includes leading zeros.
•
X10@
=
Command data section. For web encoding for
numbers.
•
The
X10(
X11)
*
*
*
Configure serial
E X10!
port parameters
24
View serial port
E X10!
parameters
E
24
Configure mode
1 *
View serial mode
E X10!
URL Encoded (Web)
(Host to Processor)
X10(
X11)
X11!
} X11)
*
*
*
RS
X10!
X10!
W
%2A
}
<data> •
W 05 %2A 4 %2A 7 %2A 3L RS
X11! sequence is optional. If X10( and X11) are not specified, the default values are used.
X11^
X11&
X11*
X11(
*
,
,
,
X10!
X11^
W
%2A
}
X10!
|
CP
W
CP
X12)
X12)
}
CY
W 1 %2A
}
X10!
|
CY
W
CY
WindoWall Pro Series • Remote Configuration and Control
Response
(Processor to Host)
X11)
X11!
| X10@
%2A
%2A
RS
{Response from command}
|
{data}
{Response from command}
X10@
, be sure to convert non-alphanumeric characters to hex
}
CP
X11&
X11*
X11(
%2A
%2A
%2A
X10!
Cpn
• Ccp
X11^
X11&
X11*
,
,
|
X12)]
CY
Cpn1 • Cty
X12) ]
Additional Description
]
|
CP
X11^
X11&
X11*
X11(
,
,
,
CP
X11^
Set baud rate
, parity
X11&
X11*
, data bits
, and
X11(
X10!
stop bits
for port
X11^
= 2400, 4800, 9600,
19200, 38400, or
115200.
X11&
= odd, even, none,
mark, or space.
(Only the first letter is
required.)
X11*
= 7 or 8
X11(
= 1 or 2
X11(
]
,
CP
X12)
Select serial mode
the rear panel RS-232/422
X12):
port. For
0 = RS-232
1 = RS-422
View current port mode.
]
.
for
40
Advertisement
Table of Contents
