Basic Sis Commands - Extron electronics Quantum Ultra Series Setup Manual

5. When finished, save the window layout as a preset as follows:
In the Presets list in the lower-left corner of the screen (see figure 11,
a.
preset to be saved.
Click Save. The preset slot becomes a text field with the label Window Preset nnn (where
b.
nnn is the three-digit preset number that indicates the preset slot number).
c. Enter a name for the preset (32 characters maximum) or click outside the text field to keep the current name.
If configuring in Preview mode, click the Take button (
6.

Basic SIS Commands

The Quantum Ultra Series can be controlled with SIS commands via a USB, RS-232, or LAN connection. The following table
lists some basic commands. For a full list of SIS commands and variables see the Quantum Ultra Series User Guide, available at
www.extron.com.
Command
Input Selection
Select input
View current input
Window Presets
Recall window preset
Recall preset with audio
Window Border Style (These commands apply to Quantum Ultra and Quantum Ultra II only.)
Set window border style
View window border style
Audio
Select audio source
IP Configuration (These commands apply only to the LAN A port. A Commit and Reboot command is required for changes to persist.)
Set DHCP on and off
View DHCP setting
Set IP address
View IP address
Rebooting the System
Commit and reboot
X!
KEY: = Input (assigned by VCS): 0001 – 9999. Response is four digits with leading zeros.
0001 – 0999 = physical video connections on all Quantum chassis in the system.
1000 – 9999 = Sources defined in the system and not connected to an input card (Picture, RSS, VNC, Text, or Clock).
X#
Canvas: 01 – 10. Response is two digits with a leading zero.
=
X%
Window: 001 – 999. Response is three digits with leading zeros.
=
X1)
= On or off: 0 = off (disabled), 1 = on (enabled).
X2%
Window preset: 001 – 128. Response is three digits with leading zeros.
=
X7%
Window border style preset: 000 – 127. 000 = no border. Response is three digits with leading zeros.
=
X11$
IP address in the format nnn.nnn.nnn.nnn. Default is 192.168.254.254.
=
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and
related topics, see the
13
© 2017-2021 Extron — All rights reserved. All trademarks mentioned are the property of their respective owners.
ASCII Command Response
(Host to Processor) (Processor to Host)
X# X% X!
* * ! Grp
X# X% X!
* !
X# X2%
1* * . 1Rpr
3* X# * X2% . 3 Rpr X# * X2%
E X# X% X7%
B * * WNDW } Wndw B
X# * X% X7%
E
B WNDW }
X! X# $ Grp
*
E X1)
DH } Idh
E X1)
DH }
E X11$
CI }
Ipi•
E X11$
CI }
E 1BOOT } Boot1 ]
Extron Safety and Regulatory Compliance Guide
5 on the previous page), select a slot for the
6
) if you want to apply the preset to all displays in the system.
Additional Description
X# X% X!
•Win •In ] Select input
] View current input
X# X2%
]
* Recall window preset
] Recall window preset
audio tie.
X# X% X7%
* * ] Set the border style of window
X7%
to
] View border style
X#• In X!• Aud ]
Select audio from input
X1) Enable or disable DHCP.
]
]
View DHCP setting
X11$
]
Set the IP address for the unit to
] View IP address
Commit changes and reboot Quantum Ultra.
on the Extron website.
X! X%
for window on Canvas
X! X%
in window on Canvas
X2% X#
on Canvas
X2% X#
to canvas
X%
, on Canvas
.
X7% X%
for window on Canvas
X! X#
for canvas
X1)
. Default is 0 (off).
X11$
.
X11$
.
www.extron.com
X#
.
X#
.
.
including
X#
,
X#
.
.
68-2760-50
Rev. G 12 21