1. Manuals
  2. Brands
  3. ALLIANCE Manuals
  4. Washer
  5. AA9231
  6. Service

ALLIANCE AA9231 Service

Automatic washer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Automatic
Washers
Refer to Page 6 for Model Numbers
W001C
Part No. 32283R2
www.comlaundry.com
April 2004

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AA9231 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ALLIANCE AA9231

Summary of Contents for ALLIANCE AA9231

  • Page 1 Automatic Washers Refer to Page 6 for Model Numbers W001C Part No. 32283R2 www.comlaundry.com April 2004...

  • Page 3: Table Of Contents

    All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 4 Electronic Control Nos. 31306 or 31309 Cycle Sequence (Three Cycle).......93 Electronic Control Nos. 31305 or 31308 Cycle Sequence (Four Cycle) ........94 Electronic Control Nos. 31304P or 31307 Cycle Sequence (Five Cycle).........95 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 5: Section 1 - Safety Information

    • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the product is properly grounded and to reduce the risk of fire, electric shock, serious injury or death. W006R2 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 6: Locating An Authorized Servicer

    Locating an Authorized Servicer Alliance Laundry Systems is not responsible for personal injury or property damage resulting from improper service. Review all service information before beginning repairs. Warranty service must be performed by an authorized technician, using authorized factory parts. If service is required after the warranty expires, Alliance Laundry Systems also recommends contacting an authorized technician and using authorized factory parts.

  • Page 7: Section 2 - Introduction

    When calling or writing about your product, be sure to mention model and serial numbers. Model and serial numbers are located on nameplate(s) as shown. Nameplate W162S 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 8: Model Identification

    NA5521 NA4522 NA3520 AA3110 NA7521 NA6520 NA5520 NA4521 NA3512 NA2510 NA7321 NA6332 NA5331 NA4520 NA3511 NA2310 AA7231 NA6331 NA5330 NA4321 NA3510 NA2110 AA7131 NA6321 NA5321 NA4320 NA3320 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 9: Section 3 - Troubleshooting

    • Refer to appropriate wiring diagram. †Inoperative electronic control. • Refer to Section 8 to check out the electronic control operation. * Mechanical Timer Models only † Electronic Control Models only 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 10: No Warm Water

    • Refer to appropriate wiring diagram and reattach wire. Broken, loose or incorrect wiring. • Refer to appropriate wiring diagram. * Mechanical Timer Models only † Electronic Control Models only © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 11: No Agitation

    • Repair or replace transmission assembly. †Inoperative electronic control. • Refer to Section 8 to check out the electronic control operation. * Mechanical Timer Models only † Electronic Control Models only 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 12: Slow Spin Or No Spin

    • Refer to appropriate wiring diagram. †Inoperative electronic control. • Refer to Section 8 to check out the electronic control operation. * Mechanical Timer Models only † Electronic Control Models only © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 13: Drive Motor Overload Protector Cycles Repeatedly

    • Replace with correct screws or tighten. Base damaged (washer was dropped). • Replace base assembly. Balance ring not positioned properly on • Refer to Paragraph 45. transmission assembly. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 14: Water Leaking From Outer Tub

    • Replace gasket. Obstruction in drain causing water to come over top • Remove obstruction. of outer drain tub cover. Tub-to-pump hose leaking at clamp. • Tighten clamp. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 15: Section 4 - Grounding

    If a voltage reading is measured 115 ± 12 other than that illustrated, the qualified electrician should correct the problem. 115 ± 12 Round Grounding Prong W011G Figure 1 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 16: Power Cord To Cabinet Top, Cabinet Top To Control Hood Mounting Bracket, Pressure Switch Mounting Bracket And Ground Tab On Graphic Panel

    BRACKET, PRESSURE SWITCH MOUNTING BRACKET AND GROUND TAB ON GRAPHIC PANEL Power Cord Ground Wires Ground Mechanical Timer Models Wires Power Cord Ground Wires Ground Wires Electronic Control Models Figure 2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 17: Main Wire Harness To Top Left Rear Corner Gusset Of Cabinet

    16. MAIN WIRE HARNESS TO TOP LEFT REAR CORNER GUSSET OF CABINET Ground Wires Ground Wires Mixing Valve Guard Through Serial No. R1339649XG Starting Serial No. R1339650XG Figure 3 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 18: Motor To Mounting Bracket To Base (If Present)

    W003 17. MOTOR TO MOUNTING BRACKET TO BASE (if present). Ground Wire Ground Wire to Base (Discontinued starting Serial No. 42P74967) Figure 4 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 19: Section 5 - Service Procedures

    End Cap (Right) Graphic Panel Screw W419P Clip GRAPHIC PANEL, CONTROL HOOD AND CONTROLS (Models AA9131, NA8631, NA8531, NA8331, NA6532, NA6531, NA6530, NA6332 and NA6331) Figure 5 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 20 Electronic Knob Control Assembly End Cap (Right) Graphic Panel Screw W419P Clip GRAPHIC PANEL, CONTROL HOOD AND CONTROLS (Models AA7131, NA5531, NA5530, NA5331 and NA5330) Figure 6 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...
  • Page 21 (Models NA5721, AA5121, NA4621, NA4522, NA4521, NA4520, NA4321, NA4320, AA4111, AA4110, NA3612, NA3520, NA3512, NA3511, NA3510, NA3320, NA3312, NA3311, NA3310, AA3111, AA3110, NA2510 and NA2310) Figure 7 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 22 Assembly Graphic Screw Panel Screw Eaton Timer End Cap Screw (Right) Timer Knob Timer Knob W436P Skirt GRAPHIC PANEL, CONTROL HOOD AND CONTROLS (Model NA2110) Figure 8 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 23: Timer

    Refer to the control hood mounting bracket, and that the Figure 9. two screws are torqued down between 12 to 18 inch pounds (14 to 21 cm-kg). 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 24: Temperature Switch

    Refer to Figure 5, 6, 7 or 8. a. Remove six screws (3 on top and 3 at lower front) holding hood assembly to control hood Figure 11 rear panel and cabinet top. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 25: Agitator

    If hooks are placed between the fin area, damage to agitator may occur. c. Using a rocking motion (back and forth) carefully lift agitator off drive bell. Indent Figure 13 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 26 NOTE: Soapy water will aid in the assembly of the IMPORTANT: If large nut is turned clockwise when pulling drive bell, you will twist off the 1/4 seal onto the hub. inch bolt. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 27: Front Panel

    Figure 16 to lock under bottom edge of drive bell. NOTE: Do not push agitator onto drive bell any further than necessary. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 28: Pump Belt

    Remove belt from motor pulley and pull belt out through front of motor mount. IMPORTANT: Drive belt MUST be replaced with belt No. 28808 (special clutch-type belt) for proper washer operation. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...
  • Page 29 Retighten the four attaching screws. Refer to Figure 18. Drive Pulley Wire harness must be installed ahead of spring. Drive Belt Motor Attaching Helper Screws Spring Idler Spring Figure 18 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 30: Motor And Mounting Bracket

    NOTE: Refer to Figure 20 for motor and mounting d. If present, remove screw holding ground wire bracket assembly sequence. to washer base. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 31: Idler Lever And Pulley

    NOTE: Refer to Figure 20 for idler lever and pulley assembly sequence. c. Apply No. 03637 Lubricant to the area of idler lever making contact with motor mounting bracket. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 32 Shaft Ground Clip Clip (Clips to the motor Idler mounting bracket) Pulley Felt Washers Nylatron Washer Belt (Agitate and Spin) Retainer W416P Ring Belt (Pump) Figure 20 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 33: Motor Drive Pulley Or Pump Pulley

    Hose Inlet Hose to Pump Assembly Clamps Hose Drain Hose Recirculating Hose Pump Return Hose Clamp Mounting Bracket Pump Attaching Screws WA102-SV WA101-SV Figure 21 Figure 22 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 34: Cabinet Top Assembly

    NOTE: Cabinet top is self-supporting, however, a small chain may be used for additional support. Refer to Figure 24. Figure 24 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...
  • Page 35 Refer cabinet top. to Figure 23. e. Tape loading door closed. f. Lift front of cabinet top slightly and pull forward to disengage from rear hold-down brackets. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 36: Door And Out-Of-Balance Switch And Bracket Assembly

    Switch Shield Attaching Screw Switch Lever Bracket Lid Switch Guard Spring (starting Serial No. R1339650XG and continuing through R1566483YG) Cabinet Attaching Screw W438P Attaching Screws Figure 25 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 37: Mixing Valve Assembly

    Pull mixing valve out toward front of washer far enough to permit disconnecting water inlet hoses from mixing valve. Refer to Figure 26. d. Disconnect wires from mixing valve solenoids. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 38 Refer to Figure 27. Starting with this hole, place each spring clip in its respective hole and snap in place. Refer to Figure 27 for proper clip installation. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 39: Water Seal And Hub Assembly

    Then carefully push the filter down into Assembly the washtub until all the pins snap into their respective holes. Figure 30 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 40 DO NOT replace only one of the two seals. j. Remove large hex nut using a No. 306P4 Hex Wrench. Refer to Figure 30. k. Remove spline insert from transmission tube. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...
  • Page 41 Then place the hex nut on the with bronze portion of the seal. Refer to transmission tube (with the larger inside bevel Figure 32. on the nut toward the spline insert). Tighten the 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 42 Slowly rotate the agitator until the fingers on the underside of agitator line up with the large m. Reinstall filler hose on backflow preventer. slots on drive bell. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 43: Outer Tub

    Lubricate the gasket with liquid soap to aid in assembly. Cover must be placed on outer tub so notch on top edge of outer tub cover is 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 44 Refer to Figure 33. motor mounting bracket, idler lever extends out through rear of bracket. When removing or Notch Hose Centering Spring Centering Spring Figure 33 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...
  • Page 45 Remove screws and lockwashers holding each support leg to outer tub. Refer to Figure 34. Then lift transmission, balance ring and pivot dome off tub. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 46: Drive Pulley And Helix

    NOTE: After installing belt, adjust belt. Refer to Paragraph 51. Pivot Drive Dome Pulley Brake Assembly Lower Bearing Transmission Housing Assembly Plate Screw and Balance Lockwasher Ring Figure 34 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...
  • Page 47 NOTE: When reinstalling motor and mounting Lubricate helix ramps also. Refer to Figure 36. bracket, positioning tab on right side of mounting 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 48: Brake Assembly

    NOTE: Refer to Figure 36 for assembly sequence. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 49: Lower Bearing Housing

    IMPORTANT: Use care when releasing the idler have to be drained to prevent spillage on the floor. lever tension. If the idler spring or helper spring is overstretched, washer operation will be affected. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 50 IMPORTANT: When installing lower bearing housing, apply No. 27604P Anti-Seize compound to the area of transmission tube that will be contacting bearing. Refer to Figure 37. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 51: Transmission Assembly

    DO NOT lift up on lint filter as you could This will prevent the possibility of idler lever or damage it. Grasp top flange of washtub and remove pulley damage. from outer tub. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 52 IMPORTANT: When reinstalling spring, be sure it noise, wear or no spin. is inserted into groove in large spline of transmission tube. Use spring tool, No. 242P4, when installing spring. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...
  • Page 53 Seals and h. Remove special screw, lockwasher and flat bearings are not available separately. washer holding drive pinion to input shaft. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 54 Shaft Gear (Input) Identification Groove Agitator Pinion Dowel Rack Slide Dowel Screw Transmission Cover Assembly Loctite (Use as a sealant between Transmission Case and Cover.) Figure 38 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...
  • Page 55 To prevent seal damage, insert input shaft into be contacting upper and lower bearings. cover starting at outer end of cover tube. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 56: Balance Ring

    Refer to Figure 34. c. Lift complete pivot dome (with drive pulley, brake assembly, lower bearing housing, transmission assembly, and balance ring attached) off outer tub. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 57: Snubber Pads

    NOTE: Springs must be hooked into the center of with fluffed side against the base dome and the three notches. Refer to Figure 42. make sure pads are equally spaced. Refer to Figure 40. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 58 Reconnect washer power cord and open water supply valves. NOTE: Washer must be run through a complete cycle to make sure it is operating properly. Centering Spring Figure 42 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...
  • Page 59 W003 Drive Pulley Helper Spring Drive Belt Back Hole Idler Hook Lever Idler Lever Spring Spring Here Figure 43 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 60 Section 5 Service Procedures Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 61: Section 6 - Adjustments

    (to prevent damage to washer components). DO NOT slide washer across floor once the leveling legs have been extended, as legs and base could become damaged. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 62: Pressure Switch

    Slide Pressure Switch it will go, then tighten the four screws. This mounting bracket adjustment is necessary to ensure Figure 45 the proper belt drive action. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 63: Belt (Pump)

    After belt tension is obtained, tighten the three pump mounting bracket screws. Motor Pump 1/2" Pulley Pulley (12.7 mm) Pump Belt Figure 47 Pump Attaching Screws Figure 46 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 64: Out-Of-Balance Switch Trigger

    Example: If the springs are placed in the upper notch then the trigger must be moved to the extreme right for proper trigger operation. Cover Trigger Screw Figure 48 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 65: Section 7 - Test Procedures

    Continuity (K & G) OPEN Blue to Red OPEN Continuity (K & F) Red to Yellow Continuity (F & L) OPEN Brown to Yellow OPEN Continuity (G & L) 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 66 Section 7 Test Procedures Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 67: Section 8 - Service Procedures Unique To The Electronic Control Model Washers

    To reduce the risk of an electric shock, washer. serious injury, death or fire, DO NOT use an W028 extension cord or an adapter to connect washer to electrical power source. W169 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 68: Grounding Instructions

    Check with a qualified electrician or service person if you are in doubt as to whether the dryer is properly grounded. W038 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...
  • Page 69 AA9131, NA8631 and NA8531 No longer available NA8331 31307 NA6532, NA6531, NA6530 31305 NA6332, NA6331 31308 AA7131, AN5531, NA5530 No longer available NA5331, NA5330 31309 Figure 52 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 70: Washer Operation

    Washer will not start until the GO pad is pressed. The washer will stop (pause) for a brief period of time before the wash and rinse spins. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 71: Automatic Preprogrammed Cycles

    Temperature Time Time Regular Normal Warm Perm Press Normal Warm Delicates Normal Warm Knit Normal Warm Soak Normal Warm 30 (Soak) 10 (Agitate & Spin) Figure 53 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 72: Status Lights

    RESET The RESET pad functions the same as the STOP pad. Pressing it once stops the washer, pressing it two times in succession cancels the cycle. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 73: Customizing Preprogrammed Cycles

    HEAVY pad and a number will appear in the display area. Press HEAVY again and the time will increase by one minute. Refer to Figure 54. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 74 MEMORY SAVE pad. The old memory cycle will be deleted and the new cycle will be memorized in its place. NOTE: The SIGNAL and DELAYED START cannot be saved in memory. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...
  • Page 75 DELAYED Will Be START option. It will also cancel the entire cycle. NOTE: Rinse the dispenser thoroughly after it has been used to dispense detergent. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 76: Troubleshooting Electronic Control

    1. This test routine will only light LEDs pertaining to hardware model selected. 2. When last step in table is finished, routine sequence will repeat. 3. Each output is on for two seconds. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...
  • Page 77 White (P1) Cold Water Valve Gray (P8) Ground Green (P9) Loading Door Motor Switch Blue (COM) Pink/Blue (N.O.) CONNECTION RELAY AND TRANSFORMER DIAGRAM (ELECTRONIC CONTROL) Figure 55 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 78 Agitate Agitate Agitate Warm Rinse Agitate Soak Hold Agitate Knits Agitate Delicates Agitate Perm Press Agitate Regular Agitate Spin Spin Spin * None (All off) Figure 56 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 79: Failure Symptoms

    1. Is loading door closed? 2. Loading door switch operating properly? 3. Is washer plugged into properly polarized outlet and washer effectively grounded? Refer to Paragraph 55. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 80: Symptom: Flashing Display

    “P1” (neutral) with the loading Inspect loading door switch. door closed, and zero Volts between “N.O.” and “P1” with the loading door open. Recheck troubleshooting sequence. If problem persists, replace control. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 81: Symptom: Indicator Leds (I.e. Wash, Rinse, Spin, Unbalanced) Do Not Light

    Correct wiring wiring? Recheck troubleshooting sequence. If problem persists, replace control. * For precision, this measurement must be taken with a digital multi-meter set on 200 Ohm scale. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 82: Symptom: Tripped Circuit Breaker Or Blown Fuse

    Recheck troubleshooting sequence. If problem persists, replace control. * For precision, this measurement must be taken with a digital multi-meter set on 200 Ohm scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 83: Symptom: Washer Will Not Fill Or Wrong Temperature Fill

    Use water fill and only cold water relay “K5 ” will be ADVANCE pad to advance cycle to SPIN if energized for cold water fill. necessary. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 84: Symptom: Washer Will Not Agitate Properly

    Replace control. and “P1” (neutral) on control? Motor Relay K2 Zero Volts between “P3” (START/SPIN) and Replace control. “P1” (neutral) on control? Problem not related to electronic control. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 85: Symptom: Washer Will Not Spin Properly

    (START/SPIN) and “P1” (neutral) on control? Motor Relay K1 Zero Volts between terminals “P2” Replace control. (START/AGITATE) and “P1” (neutral) on control? Problem is not related to electronic control. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 86: Control Replacement

    When removing wires from the control, hold down on the board near the appropriate terminal and disconnect the wires using a pliers. Do not pull on wires. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 87: Electronic Control Board Replacement Report

    Both copies of this form must be completed and returned with the control board. Warranty is void if control board is returned improperly packed or damaged. Form No. 8027R1 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 88 Section 8 Service Procedures Unique to the Electronic Control Model Washers Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 89: Timer No. 31238 Cycle Sequence

    360.00 *ON SINGLE SPEED MODEL WASHERS, ALL SPEEDS ARE FAST. KEY: H = HOT W = WARM C = COLD TIMER NO. 31238 CYCLE SEQUENCE (TWO CYCLE) 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 90: Timer No. 31239 Cycle Sequence (Three Cycle)

    360.00 *ON SINGLE SPEED MODEL WASHERS, ALL SPEEDS ARE FAST. KEY: H = HOT W = WARM C = COLD TIMER NO. 31239 CYCLE SEQUENCE (THREE CYCLE) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 91: Timer No. 31240 Cycle Sequence

    *ON SINGLE SPEED MODEL WASHERS, ALL SPEEDS ARE FAST. †SOAK IS “INFINITE.” PREWASH IS 24:37 PLUS FILL. KEY: H = HOT W = WARM C = COLD TIMER NO. 31240 CYCLE SEQUENCE (FIVE CYCLE) 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 92: Timer No. 32039 Cycle Sequence

    5.96 *ON SINGLE SPEED MODEL WASHERS, ALL SPEEDS ARE FAST. KEY: H = HOT W = WARM C = COLD TIMER NO. 32039 CYCLE SEQUENCE (FOUR CYCLE) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 93: Timer No. 32039 Cycle Sequence

    5.96 *ON SINGLE SPEED MODEL WASHERS, ALL SPEEDS ARE FAST. KEY: H = HOT W = WARM C = COLD TIMER NO. 32039 CYCLE SEQUENCE (FOUR CYCLE) 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 94: Timer No. 32228 Cycle Sequence

    *ON SINGLE SPEED MODEL WASHERS, ALL SPEEDS ARE FAST. †SOAK IS “INFINITE”. PREWASH IS 34:37 PLUS FILL. KEY: H = HOT W = WARM C = COLD TIMER NO. 32228 CYCLE SEQUENCE (FIVE CYCLE) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 95: Electronic Control Nos. 31306 Or 31309 Cycle Sequence (Three Cycle)

    5:00 †TIME WILL VARY DEPENDING ON SELECTION. KEY: H = HOT W = WARM C = COLD ELECTRONIC CONTROL NOS. 31306 OR 31309 CYCLE SEQUENCE (THREE CYCLE) 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 96: Electronic Control Nos. 31305 Or 31308 Cycle Sequence (Four Cycle)

    ** THIS TIME WILL BE 3:00 WHEN EXTRA RINSE IS SELECTED. SPIN 5:00 KEY: H = HOT W = WARM C = COLD ELECTRONIC CONTROL NOS. 31305 OR 31308 CYCLE SEQUENCE (FOUR CYCLE) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 97: Electronic Control Nos. 31304P Or 31307 Cycle Sequence (Five Cycle)

    † 0 to 9 hours FILL H,W,C Variable AGITATE 5:00 PAUSE (SOAK) † 15:00 - 85:00 SPIN 4:00 ELECTRONIC CONTROL NOS. 31304P OR 31307 CYCLE SEQUENCE (FIVE CYCLE) 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 98 Section 9 Cycle Sequence Charts Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 99: Section 10 - Internal Wiring Of Washer Motor Switch

    (High Speed) (High Speed) 4 Pole Auxiliary 4 Pole Auxiliary (Start Winding) (Start Winding) External Wires External Wires Emerson General Electric 27658P MOTOR ASSEMBLY (1 SPEED MOTORS) 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 100 (High Speed) (High Speed) 4 Pole Auxiliary 4 Pole Auxiliary (Start Winding) (Start Winding) External Wires External Wires General Electric Emerson 27179P MOTOR ASSEMBLY (2 SPEED MOTORS) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 101: Section 11 - Wiring Diagrams

    W030 WIRING DIAGRAMS AND SCHEMATICS FOUND ON THE FOLLOWING PAGES ARE FOR MODELS COVERED IN THIS MANUAL. 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 102: Models Aa9131, Na8631, Na8531, Na8331

    W030 MODELS AA9131, NA8631, NA8531, NA8331, AA7131, NA6532, NA6531, NA6530, NA6332, NA6331, NA5531, NA5530, NA5531 AND NA5330 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 103: Models Na7521 And Na7321

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NA7521 AND NA7321 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 104: Models Na6621, Na6522, Na6521, Na6520, Ng6321 And Aa6121

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NA6621, NA6522, NA6521, NA6520, NG6321 AND AA6121 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 105: Model Na5721

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODEL NA5721 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 106: Models Na5521, Na5520, Na5321 And Na5320

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NA5521, NA5520, NA5321 AND NA5320 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 107: Models Na4521, Na4520, Na4321 And Na4320 (Through Serial No. 43R19503) And Na3520 And Na3320

    W030 MODELS NA4521, NA4520, NA4321 AND NA4320 (THROUGH SERIAL NO. 43R19503) AND NA3520 AND NA3320 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 108: Models Na4521, Na4520, Na4321 And Na4320 (Starting Serial No. 43R19504) And Aa5121, Na4621, Na4522, Na3520 And Na3320

    W030 MODELS NA4521, NA4520, NA4321 AND NA4320 (STARTING SERIAL NO. 43R19504) AND AA5121, NA4621, NA4522, NA3520 AND NA3320 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 109: Models Aa4111, Aa4110, Na3612, Na3512, Na3511, Na3510, Na3312, Na3311, Na3310, Aa3111 And Aa3110

    W030 MODELS AA4111, AA4110, NA3612, NA3512, NA3511, NA3510, NA3312, NA3311, NA3310, AA3111 AND AA3110 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 110: Models Na2510 And Na2310

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NA2510 AND NA2310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

  • Page 111: Model Na2110

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODEL NA2110 32283 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 112 Section 11 Wiring Diagrams Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32283...

This manual is also suitable for:

Na8631Na8531Na7521Na7321Aa7231Aa7131 ... Show all

Table of Contents