Do you have a question about the AWN43RSN115CW01 and is the answer not in the manual?
Questions and answers
Darlene Fegatilli
March 17, 2025
Does my washer have a filter I can clean without a lot of tools?
1 comments:
Mr. Anderson
May 14, 2025
Yes, the ALLIANCE AWN43RSN115CW01 washer has a filter that can be accessed and replaced. According to the installation instructions, you can unplug the washer, move it away from the wall, and locate the filter compartment at the lower portion of the machine. The filter cover can be removed using a flat-head screwdriver, allowing for maintenance or replacement.
This answer is automatically generated
Elizabeth McDougall
March 6, 2025
Washer will not spin
1 comments:
Mr. Anderson
March 6, 2025
The ALLIANCE AWN43RSN115CW01 washer may not be spinning due to the following reasons:
1. Unbalanced Load – The machine has sensed an unbalanced load. Re-balance the load, ensuring large items are distributed evenly. Adding towels on the opposite side can help balance the load.
2. Excessive Suds or Slow Draining – Too much detergent or slow drainage can leave excess water in the tub, preventing proper spinning.
3. Fatal Unbalance Error – This could be due to broken or disconnected wires to the unbalance switch, a stuck switch, a broken spring, or the machine being unlevel, causing the tub to lean on the unbalance switch.
4. Communication Error – A broken wire or poor connection at the H2 connector between the FEC and drive board can cause issues.
5. Board ID Error – If an incorrect replacement control was installed, the washer may not function properly.
6. Board Shorted Error – A stuck or welded relay (K1) on the drive board may prevent spinning. Tapping the relay might help, but replacing the drive board may be necessary.
7. Unleveled Washer – If the washer is not level, adjust the leveling legs.
8. Broken Balance Ring or Friction Ring – If these components are damaged, they may need replacement.
9. Weak or Spongy Floor – If the washer is installed on an unstable surface, relocating it to a more solid floor may be necessary.
This answer is automatically generated
Mike Krajna
February 22, 2025
bypass lid lock
1 comments:
Mr. Anderson
February 22, 2025
The manual does not provide instructions on bypassing the lid lock. However, it mentions troubleshooting steps for lid lock errors. If the lid lock is malfunctioning, check for broken wiring, misalignment, or moisture affecting the lock. Allow it to dry if wet and ensure proper lid alignment. For safety and proper operation, it is recommended to follow manufacturer guidelines and not attempt to bypass safety mechanisms.
Need help?
Do you have a question about the AWN43RSN115CW01 and is the answer not in the manual?
Questions and answers
Does my washer have a filter I can clean without a lot of tools?
Yes, the ALLIANCE AWN43RSN115CW01 washer has a filter that can be accessed and replaced. According to the installation instructions, you can unplug the washer, move it away from the wall, and locate the filter compartment at the lower portion of the machine. The filter cover can be removed using a flat-head screwdriver, allowing for maintenance or replacement.
This answer is automatically generated
Washer will not spin
The ALLIANCE AWN43RSN115CW01 washer may not be spinning due to the following reasons:
1. Unbalanced Load – The machine has sensed an unbalanced load. Re-balance the load, ensuring large items are distributed evenly. Adding towels on the opposite side can help balance the load.
2. Excessive Suds or Slow Draining – Too much detergent or slow drainage can leave excess water in the tub, preventing proper spinning.
3. Fatal Unbalance Error – This could be due to broken or disconnected wires to the unbalance switch, a stuck switch, a broken spring, or the machine being unlevel, causing the tub to lean on the unbalance switch.
4. Communication Error – A broken wire or poor connection at the H2 connector between the FEC and drive board can cause issues.
5. Board ID Error – If an incorrect replacement control was installed, the washer may not function properly.
6. Board Shorted Error – A stuck or welded relay (K1) on the drive board may prevent spinning. Tapping the relay might help, but replacing the drive board may be necessary.
7. Unleveled Washer – If the washer is not level, adjust the leveling legs.
8. Broken Balance Ring or Friction Ring – If these components are damaged, they may need replacement.
9. Weak or Spongy Floor – If the washer is installed on an unstable surface, relocating it to a more solid floor may be necessary.
This answer is automatically generated
bypass lid lock
The manual does not provide instructions on bypassing the lid lock. However, it mentions troubleshooting steps for lid lock errors. If the lid lock is malfunctioning, check for broken wiring, misalignment, or moisture affecting the lock. Allow it to dry if wet and ensure proper lid alignment. For safety and proper operation, it is recommended to follow manufacturer guidelines and not attempt to bypass safety mechanisms.
This answer is automatically generated