1. Manuals
  2. Brands
  3. ALLIANCE Manuals
  4. Washer
  5. CCN020HNF
  6. Installation operation & maintenance

ALLIANCE CCN020HNF Installation Operation & Maintenance

Hide thumbs
Table of Contents

Advertisement

Quick Links

Washer-Extractors
Cabinet Hardmount
Design 2 and 3 Models
Refer to Page 8 for Model Identification
Original Instructions
CHM1786C_SVG
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. F8429301ENR15
www.alliancelaundry.com
May 2015

Advertisement

Table of Contents
loading

Related Manuals for ALLIANCE CCN020HNF

Summary of Contents for ALLIANCE CCN020HNF

  • Page 1 Washer-Extractors Cabinet Hardmount Design 2 and 3 Models Refer to Page 8 for Model Identification Original Instructions CHM1786C_SVG Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Part No. F8429301ENR15 www.alliancelaundry.com May 2015...

  • Page 3: Table Of Contents

    Circuit Breakers and Quick Disconnects............49 © Copyright 2015, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher.
  • Page 4 Maintenance....................71 Daily......................71 Beginning of Day..................71 End of Day....................71 Weekly......................71 Monthly....................... 72 Quarterly......................73 Care of Stainless Steel................... 75 Disposal of Unit..................76 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 5: Safety Information

    NOTE: The word “NOTE” is used to communicate in- stallation, operation, maintenance or servicing informa- tion that is important but not hazard related. © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 6: Important Safety Instructions

    DO NOT bypass any safety devices or ing to the manufacturer’s instructions may result in conditions tamper with the controls. which can produce bodily injury and/or property damage. © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 7: Safety Decals

    Safety decals appear at crucial locations on the machine. Failure to maintain legible safety decals could result in injury to the oper- ator or service technician. Use manufacturer-authorized spare parts to avoid safety hazards. © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 8: Introduction

    SCU020WXV UCZ020GNF HCN020KDV ICN020KNF SCL020WEF SCN020WEV SCU020WYV UCZ020HNF HCN020KEF ICN020KNV SCL020WEV SCN020WYF SCY020JDV HCN020KEV ICN020KXF SCL020WXF SCN020WYV SCY020JEF HCN020KXF ICN020KYF SCL020WYV SCU020GNF SCY020KNF Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 9 SCN030WDF SCU030WDV UCZ030HNF HCN030HYF ICN030KEF SCL030WCF SCN030WDV SCU030WEV HCN030KCF ICN030KEV SCL030WCV SCN030WEF SCU030WXV HCN030KCV ICN030KNF SCL030WEF SCN030WEV SCU030WYV HCN030KDF ICN030KNV SCL030WEV SCN030WLV SCY030JDV Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 10 UCU040KNV HCN040HNF ICN040KYF SCL040HNV SCN040LCF SCU040LEV UCY040KNF HCN040HNV ICN040KYV SCL040JCF SCN040LCV SCU040LLF UCY040KNV HCN040HXF SCB040GNF SCL040JCV SCN040LDF SCU040LLV HCN040HYF SCB040HNF SCL040JDF SCN040LDV SCU040LXV Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 11 HCN080HYF ICN080HNV SCN080JCV SCU080HNF SCU080WDV UCU080KNV HCN080HYV ICN080KCF SCN080JDF SCU080JCF SCU080WEV UCY080KNF HCN080KCF ICN080KCV SCN080JYF SCU080JCV SCU080WXV UCY080KNV HCN080KCV ICN080KDF SCN080JYV SCU080JDF SCU080WYV Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 12: Delivery Inspection

    Figure 1 Replacement Parts If literature or replacement parts are required, contact the source from which the machine was purchased or contact Alliance Laun- dry Systems at +1 (920) 748-3950 for the name and address of the nearest authorized parts distributor.
  • Page 13 Shepard Street P.O. Box 990 Ripon, WI 54971-0990 U.S.A. www.alliancelaundry.com Phone: +1 (920) 748-3121 Ripon, Wisconsin Alliance International: +32 56 41 20 54 Wevelgem, Belgium © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 14: Specifications And Dimensions

    20.3 [515] 22 [559] 21.9 [556] 25.9 [657] Cylinder volume, ft 2.8 [79.3] 4.2 [119] 6.3 [178] 9.00 [255] 12.9 [365] 15.2 [430] Table 1  continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 15 1.28 [0.58] 2.40 [1.09] 4.65 [2.11] 4.65 [2.11] 5.49 [2.49] 10°F/lbs. [10°C/kg] HIGH 1.44 [0.65] 1.74 [0.79] 2.84 [1.29] 5.79 [2.63] 5.79 [2.63] 6.84 [3.10] Table 1  continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 16 * For B, Q and X-voltage models = 1 hp [.75 kW] and for N and P-voltage models = 2 hp [1.7 kW] ** 20 and 30 pound models can be prep for steam and a kit is available for conversion. N/A = Not Applicable Table 1 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 17: Machine Dimensions

    42.88 [1089] 34.52 [902] 35.52 [902] 37.46 [951] 39.71 [1009] 42.4 [1077] 4.7 [119] 4.7 [119] 4.14 [105] 4.51 [115] 4.87 [124] Table 2  continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 18 42.0 [1067] 43.0 [1092] 44.95 [1142] 47.2 [1199] 49.89 [1267] 1.5 [38] 1.5 [38] 1.5 [38] 1.5 [38] 1.5 [38] N/A = Not Applicable Table 2 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 19: 80 And 100 Pound Capacity Machines

    Machine Capacity Dimensions - 80 and 100 Pound Models, in. [mm] 51.82 [1316] 1.36 [35] 50.32 [1278] 39.24 [997] 48.68 [1236] 44.16 [1122] 48.16 [1223] Table 3  continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 20 17.91 [455] 16.66 [423] 41.5 [1054] 18.18 [462] 26.15 [664] 21.65 [550] 3.57 [91] 26.15 [664] 56.16 [1426] 30.35 [771] 1.5 [38] 53.57 [1361] Table 3 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 21: Mounting Bolt Hole Locations - 20 And 30 Pound Models

    Mounting Bolt Hole Locations – 20 and 30 Pound Models, in. [mm] Specification 2 [51] 2 [51] 26.37 [670] 29.38 [746] 20.88 [530] 23.89 [607] Table 4  continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 22 23.94 [608] 28.94 [735] 24.69 [627] 29.69 [754] 27.92 [709] 32.59 [828] 20.65 [524] 23.5 [597] 26.37 [670] 29.38 [746] 26 [660] 29.02 [737] Table 4 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 23: Mounting Bolt Hole Locations - 40 And 60 Pound Models

    3. Machine Width Figure 5 Mounting Bolt Hole Locations - 40 and 60 Pound Models, in. [mm] Specification 2 [51] 2 [51] Table 5  continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 24 32.5 [826] 36 [914] 33.54 [852] 36.87 [936] 37.25 [946] 40.5 [1029] 23.63 [600] 27.5 [699] 30.88 [784] 34.44 [875] 30.63 [778] 34.19 [868] Table 5 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 25: Mounting Bolt Hole Locations - 80 And 100 Pound Models

    Mounting Bolt Hole Locations – 80 and 100 Pound Models, in. [mm] Specification 41.5 [1054] 41.5 [1054] 39.62 [1006] 39.62 [1006] 31.62 [803] 31.62 [803] Table 6  continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 26 42.72 [1085] 35.43 [900] Inside 52.86 [1342] 47.16 [1197] Outside 35.43 [900] 42.72 [1085] Inside 47.16 [1197] 52.86 [1342] N/A = Not Applicable Table 6 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 27: Floor Mounting Layout - 20-60 Pound Models

    5.99 [152] edge of pad (minimum) Distance of machine base to 2.52 [64] 2.51 [64] 2.81 [71] 5.18 [131] edge of pad (minimum) Table 7 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 28 Mounted without bases (min- 5.14 [131] 5.12 [130] 4.63 [118] 4.06 [103] imum) Mounted with bases (mini- 5.5 [139] 5.5 [139] 4.88 [124] 4.44 [112] mum) Table 8 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 29 27.6 [702] 28.0 [710] 27.5 [699] (minimum) Distance from front bolt to 5.26 [134] 5.26 [134] 6.19 [157] 8.9 [226] edge of pad (minimum) Table 9 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 30: Floor Mounting Layout - 80 And 100 Pound Models

    24 [610] Distance of machine base to edge of pad (minimum) 4.98 [126] Distance of machine base to edge of pad (minimum) 8 [203] Table 10 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 31 Standard Mount Side-by-Side - 80 and 100 Pound Models, in. [mm] Description 80-100 Distance to wall (minimum) 24 [610] Adjacent unit bolt spacing (minimum) 6 [152] Table 11 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 32 Distance to wall (minimum) 24 [610] Adjacent unit bolt spacing (minimum) 10.38 [264] IMPORTANT: When close mounting, bolt machine using inside bolt holes. Table 12 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 33 Back-to-Back Mount (refer to Table 13 ) PHM810N_SVG 1. Front of Machine 2. Machine 2 3. Rear of Machine 4. Machine 1 5. Edge of Concrete Pad Figure 13 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 34 Back-to-Back Mount - 80 and 100 Pound Models, in. [mm] Description 80-100 Adjacent rear bolt spacing (minimum) 33.3 [846] Distance from front bolt to edge of pad (minimum) 8 [203] Table 13 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 35: Installation

    Thoroughness of detail must be stressed with all foundation work to ensure a stable unit installation, eliminating possibilities of ex- cessive vibration during extract. © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 36: New Foundation

    IMPORTANT: The above instructions and recommenda- tions are conservative specifications for a typical in- stallation based on consultations with a structural en- gineer. Alliance Laundry Systems stands behind all in- stallations meeting these specifications. For alternate installation specifications based on your soil type, lo-...

  • Page 37: Machine Foundation And Pad Installation

    [64 mm] into the existing floor. The reinforcing should be 12 ed, refer to Figure 20 and Table 18 . inches [305 mm] on center each way around entire perimeter. © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 38 Installation 14. Proceed to Machine Mounting and Grouting section. © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 39: Machine Installation

    1. Existing Floor 2. 3500 PSI (minimum) Concrete 3. Reinforcing Bar 4. Perimeter Reinforcing Bar 5. Compacted Fill (minimum 6 in. [152 mm]) Figure 17 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 40 Tie-in to Existing Floor, in. [mm] 40-60 40-60 (F-speed) (V-speed) Description 20-30 80-100 Required thickness of existing floor 4 [102] 4 [102] 6 [152] 6 [152] (minimum) Table 17  continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 41: Machine Mounting And Grouting

    15. Align the mounting holes on the machine with the corre- sponding holes on the elevated base frame. 16. Install a bolt, flat washer and locknut in each mounting hole. © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 42 3. Acrylic Adhesive 4. Anchor Bolt (minimum Grade 5 SAE rating) 5. Concrete 6. Drill Hole Size per Manufacturer Requirements 7. Edge of Pad Figure 19 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 43 700 [3.11] 940 [4.18] 1550 [6.89] 1670 [7.51] Static pressure, lbs.-ft [kN-m ] 96 [4.60] 99 [4.74] 100 [4.79] 106 [5.08] 137 [6.56] 147 [7.04] © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 44: Drain Connection

    All drain systems must be vented to prevent an air lock or siphon- ing. Use the supplied black rubber adapter and clamps to transition from the machine drain outlet to the 2 inches [51 mm] schedule © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 45 * Drain line must be vented to meet local plumbing codes. 1. Drain Hose 2. Drain Valve 3. Drain Tee 4. Overflow Hose 5. Vent Pipe* 6. Trap (as required by local codes) Figure 22 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 46: Water Connection Requirements

    1. Before installing hoses, flush the building’s water system at 125°F [51°C]and the recommended maximum water inlet tem- the machine connection valves for at least two (2) minutes. © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 47 Installation 2. Check filters in the machine’s inlet hoses for proper fit and Alliance Laundry Systems, LLC ranges of front loading commer- cleanliness before connecting. cial clothes washing machines have solenoid valves at the inlets. The water supply to the washing machines is supplied with an 3.

  • Page 48: Electrical Installation Requirements

    Installation on the serial plate on the rear of the machine, using copper con- ductors only. IMPORTANT: Alliance Laundry Systems warranty does not cover components that fail as a result of improper input voltage. Make sure the correct transformer jumper (208 Volt or 240 Volt) is in place.

  • Page 49: Input Power Conditioning

    Refer to North American Approval section for mod- W810 el-specific circuit breaker requirements. IMPORTANT: All quick disconnects should comply with the specifications. DO NOT use fuses instead of circuit breakers. © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 50: Connection Specifications

    For three-phase input, connect L1, L2, L3 and Ground as shown in Figure 28 . IMPORTANT: If a stinger leg is used for three-phase in- put, it MUST be connected to L3. © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 51: Phase Adder

    IMPORTANT: Do not use a phase adder on any ma- chine. Thermal Overload Protector For V-speed machines, the inverter drive provides overload pro- tection for the drive motor. © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 52: North American Approval

    Voltage Cycle Phase Wire Amps F and V-Speed Models (unless otherwise noted) X (F-speed) 200–208 50/60 220-240 X (V-speed) 200-208 50/60 220-240 Table 26  continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 53 X (F-speed) 200–208 50/60 220-240 X (V-speed) 200–208 50/60 220-240 Standard 200-208 50/60 Electric 220-240 10.0 Heat Standard 440-480 50/60 Electric Heat Table 27  continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 54 440-480 50/60 Electric Heat Standard 380-415 50/60 Electric Heat NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310. Table 28 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 55 Electric 10.0 Heat Standard 380-415 50/60 Electric 10.0 Heat NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310. Table 29 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 56 Electric 10.0 Heat Standard 380-415 50/60 Electric 10.0 Heat NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310. Table 30 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 57: Ce Approval

    X (F-speed) 200–208 50/60 220-240 X (V-speed) 200–208 50/60 10/6 220-240 Standard 200-208 50/60 Electric Heat 220-240 Standard 380–415 50/60 Electric Heat Table 32  continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 58 Electric Heat P (V-Speed) Standard 380-415 50/60 Electric Heat NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310. Table 33 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 59 Phase Wire Amps F-Speed Models Standard 440-480 50/60 Electric Heat 200–208 50/60 12/8 16/10 220-240 Standard 200–208 50/60 Electric Heat 220-240 16.0 Table 35  continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 60 Amps F and V-Speed Models Standard 440-480 50/60 Electric Heat 200–208 50/60 17/11 20/16 220-240 Standard 200–208 50/60 Electric Heat 220-240 16.0 Table 36  continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 61: Specifications

    Cycle Phase Wire Amps Standard 380-415 50/60 Electric Heat NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310. Table 36 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 62: Steam Requirements (Steam Heat Option Only)

    Wear eye and hand protection when handling chemi- NOTE: Using the Internal 24VAC 300 Milliamp Control cals; always avoid direct contact with raw chemicals. Transformer is recommended by Alliance Laundry Sys- Read the manufacturer’s directions for accidental tems. contact before handling chemicals. Ensure an eye-...
  • Page 63 STEP 2: Insert Wire Wire Size 28-16AWG 0.08-1.5mm 8.5mm Strip Length CHM2336N_SVG 1. Relay Com 2. Red Jumper Wire 3. 24 VAC 4. Transformer Figure 31 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 64: Chemical Injection Using External Ac Power Source

    IMPORTANT: The external power must supply power of 240VAC or less and be protected at 3 Amps or less. © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 65: External Supply Signals

    Refer to Figure 34 for Internal Supply Connection or Figure 35 for Ex- W699 ternal AC Connection. © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 66 2. K1 Contact 3. Supply 1 Signal Figure 34 = Neutral = Power PHM824N_SVG 1. ES1 Power supply 2. K1 Contact 3. Supply 1 Signal Figure 35 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 67: Connection Of External Liquid Supplies

    NOTE: Do not attempt to make chemical injection sup- ply pump electrical connections to points other than those provided specifically for that purpose by the fac- tory. © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 68: Start Up

    1. If rotation is not counterclockwise, disconnect power to ma- chine. 2. Have a qualified electrician reverse any two motor leads at the inverter terminal block. © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 69: Operation

    CHM2244N_SVG mains the chosen wash cycle. Figure 40 11. When cycle is complete, display shows “00”. © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 70 CHM2228N_SVG 1. Liquid Detergent 2. Powder Detergent b. BLEACH CHM2229N_SVG CHM2230N_SVG 3. Liquid Bleach 4. Powder Bleach c. SOFTENER CHM2231N_SVG 5. Liquid Softener Table 39 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 71: Maintenance

    2. Inspect water inlet valve hose connections on the back of the machine for leaks. 3. Inspect steam hose connections for leaks (where applicable). © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 72: Monthly

    Proper belt tension is obtained when belt can be de- flected from normal position (refer to Figure 42 ) when moderate pressure of is applied to the point mid- way between pulleys. © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 73: Quarterly

    3. Tighten anchor bolts as specified in the Machine Mounting and Grouting section, if necessary. 4. Verify that the drain motor shield is in place and secure, if so equipped. © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...
  • Page 74 10. Verify the insulation is intact on all external wires and that all connections are secure. If bare wire is evident, call a service technician. 11. Clean inverter drive cooling fan blades (where applicable). © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 75: Care Of Stainless Steel

    Locate the pump and tubing below the machines’s injection point to prevent siphoning of chemicals into the machine. © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

  • Page 76: Disposal Of Unit

    MIX1N_SVG Figure 44 © Copyright, Alliance Laundry Systems LLC - Part No. F8429301ENR15 DO NOT COPY or TRANSMIT...

This manual is also suitable for:

Hcd020ldfHcd020ldvCcn020hnvHcl020gnfCcn020knfHcl020hdf ... Show all

Table of Contents