ALLIANCE AA9231 Service page 42

Section 5 Service Procedures
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
nut using a torque wrench or the No. 306P4 Hex
Wrench.
IMPORTANT: Torque hex nut down between 40 to
70 foot pounds (54.23 to 94.91 Nm). If torque
wrench is not available, tap hex wrench with a
hammer until hub turns or until nut will no longer
tighten.
i. Through Serial No. R1438801XN – Apply a
small amount of non-staining petroleum jelly
(such as Vaseline) to each of the sealing
surfaces where washtub gasket will contact hub
and the bottom of washtub. Carefully place the
new washtub gasket (supplied in kit) on hub.
NOTE: Be sure all traces of the old gasket are
removed from the bottom of the washtub.
Starting Serial No. R1438802XN – Place the
lint filter on hub.
j. Install washtub by grasping the top flange of the
washtub and carefully lowering washtub down
onto the gasket or lint filter and hub.
IMPORTANT: Before setting tub into place, be sure
holes in washtub line up with holes in gasket or lint
filter and hub.
k. Secure washtub to hub using four screws
previously removed.
IMPORTANT: Porcelain Washtub Models — Use
care when tightening cap screws to avoid chipping
porcelain on the washtub.
l. Carefully place the new outer tub cover gasket
(supplied in kit) around top rim of outer tub.
NOTE: When installing outer tub cover, lubricate
the cover gasket with liquid soap to aid assembly.
Cover must be placed on outer tub so notch on top
edge of outer tub cover is directly over left front clip
hole in tub. Refer to Figure 27. Starting with this
hole, place each spring clip in its respective hole and
snap into place. Refer to Figure 27 for proper clip
installation.
m. Reinstall filler hose on backflow preventer.
40
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
WARNING
NOTE:
When reinstalling filler hose, white line on hose
must be aligned with center line of backflow preventer.
Figure 26
Refer to
prevent the hose from rubbing on the flange of the tub
Figure 27
cover. Refer to
hose to obtain the proper clearance.
TO INSTALL DRIVE BELL AND NO. 39508P
SEAL KIT
a. Place the new seal head (supplied in kit) onto
hub then carefully push seal head into position
using the large end of 293P4 seal tool. Make
sure the seal is pressed down against the
shoulder on the hub.
NOTE: Soapy water will aid in the assembly of the
seal onto the hub.
b. Install the new seal seat (supplied in kit) into
the drive bell using small end of 293P4 seal
tool.
c. Position drive bell over transmission shaft.
Rotate drive bell until splines in drive bell line
up with splines on transmission shaft.
d. Place the No. 294P4 Bell Tool over top of bell.
Screw bolt into transmission shaft until it
bottoms out.
NOTE: It is not necessary to clamp the tool jaws on
the drive bell during this operation.
e. Use an adjustable wrench and turn large nut on
tool CLOCKWISE to force drive bell down
onto transmission shaft until bell bottoms out
on shaft.
f. Turn bolt out of transmission shaft and remove
tool.
g. Install the new screw and o-ring washer
(supplied in kit) in top of drive bell.
NOTE: Torque the new screw down between 45 to
55 inch pounds (5 to 6.2 Nm). Over torque will
mushroom the plastic bell.
h. Place the agitator on top of the drive bell.
Slowly rotate the agitator until the fingers on
the underside of agitator line up with the large
slots on drive bell.
. A 1/8 inch clearance is necessary to
. Loosen hose clamp and move
W003
32283