Quick Start - Extron electronics ISS 506 User Manual

ISS 506 Integration Seamless Switcher, continued
Step 5 — Serial ports
a. If desired, connect a control system or
computer to the rear panel RS-232/RS-422
port.
Pin RS-232 Function
1 — Not used
2 TX Transmit
3 RX Receive
RS232/422
4 — Not used
5 Gnd Signal
ground
6 — Not used
7 — Not used
8 — Not used
9 — Not used
b. If desired, connect a control system or
computer to the front panel Configuration
(RS-232) port. The optional 9-pin D
to 2.5 mm mini jack TRS RS-232 cable,
part #70-335-01, can be used for this
connection.
Step 6 — LAN (Ethernet) port
If desired, connect a network WAN
or LAN hub, a control system, or a
computer to the Ethernet RJ-45 port. See
chapter 2, "Installation", for details.
• Network connection — Wire as a patch
(straight) cable.
• Computer or control system connection —
Wire the interface cable as a crossover cable.
Step 7 — Power
Plug the switcher into a grounded AC source.
Front Panel Operations
Select an input
Press and release the desired input selection
button. The button lights and the selected input
displays on the program or preview monitor.
Switch the preview output to the
program output
1. If you want an effect to accompany the
switch, press one of the Effects buttons.
Wipe — The image in the preview output
"unrolls" over the top of the program output.
Dissolve — The previous program output
fades out and the image from the preview
output fades into the program output.
PIP — The image in the preview output
appears in the program output as a picture-
in-picture window.
QS-2 ISS 506 Integration Seamless Switcher • Quick Start
Quick Start —
Title — The image in the preview output
appears on top of the program output as a
title.
Press either the Cut or the Take button.
2.
Cut — If Wipe or Dissolve is selected,
RS-422 Function
— Not used
TX– Transmit (–)
RX– Receive (–)
— Not used
Gnd Signal
ground
— Not used
RX+ Receive (+)
Take — If Wipe or Dissolve is selected,
TX+ Transmit (+)
— Not used
Recall and key a saved bitmapped image
1. Press and hold the Next button. Press and
release the desired logo button. Release the
Next button.
2. Rotate either Adjust knob to select black
screen or a saved logo. Press the Next
button.
3. Rotate the two Adjust knobs to position the
logo as desired on the screen. Press the Next
button.
4. Rotate either adjust knob to select (< >) the
desired method (RGB or level) for keying out
(removing) the unwanted logo material.
5. If you selected RGB as the keying method,
rotate the adjust
to key.
6. Rotate the adjust
unwanted material.
Adjust the audio output
Rotate the Volume knob to increase or decrease
the loudness of the audio output on the Variable
Audio output connector only.
Recall presets
N
Repeatedly press and release the input button to
cycle through the saved presets (up to three) for
that input.
the preview output switches to the
program output with no effect.
If PIP or Title is selected, the preview
output appears on top of the program
output as a PIP window or title, with
no effect.
the preview output switches to
the program output with the effect
selected in step 1.
If PIP is selected, the preview
output appears on top of the
program output as a PIP window,
with a user-selected effect (see "PIP
Configuration submenu") in chapter 3.
If Title is selected, the preview
output appears on top of the
program output as a title, with no
effect.
[
to select the color plane
{ knob to key out the
You must save presets using the menu
system before you can recall them.