Asus DS300j G2 Series User Manual page 46

M M M s – M
Aking AintenAnce ode ettings AnuAlly under
You make these settings for one controller at a time.
To make maintenance mode settings:
1. At the command prompt, type net -a mod -m -c 1 -s " followed by:
• primaryip= and the IP address ,
• primaryipmask= and the subnet mask ,
• primarydns= and the DNS server IP address ,
• gateway= and the Gateway server IP address
" and press Enter .
Example:
administrator@cli> net -a mod -m -c 1 "primaryip=10.0.0.101, primaryipmask=2
55.255.255.0,primarydns=10.0.0.11,gateway=10.0.0.1"
After a moment, the comand prompt reappears, indicating that your setting was successful.
administrator@cli>
2. To verify the settings changes, at the command prompt, type net -a list -m and press Enter . The
following information displays:
administrator@cli> net -a list -m
----------------------------------------------------------------------------
CtrlId: 1 Port: 1
ProtocolFamily: IPv4(Enabled) DHCP: Disabled
IP: 10.0.0.2
IPMask: 255.0.0.0
MAC: 00:01:55:30:65:E9
DNS: 0.0.0.0
0.0.0.0
Gateway:
CtrlId: 1 Port: 1
ProtocolFamily: IPv6(Disabled)
IP: 2001::2
IPMask: ffff::
MAC: 00:01:55:30:65:E9
DNS: ::
Gateway: ::
CtrlId: 2 Port: 1
ProtocolFamily: IPv4(Enabled) DHCP: Disabled
IP: 10.0.0.3
IPMask: 0.0.0.0
MAC: 00:01:55:30:65:E9
DNS: 0.0.0.0
Gateway: 0.0.0.0
CtrlId: 2 Port: 1
ProtocolFamily: IPv6(Disabled)
IP: 2001::3
IPMask: ffff::
MAC: 00:01:55:30:65:D7
DNS: ::
Gateway: ::
40
iP 4
v
DHCP: Disabled
DHCP: Disabled
3. Repeat steps 1 and 2 above but change -c 1 (controller 1) to -c 2 (controller 2).
M M M s – M
Aking AintenAnce ode ettings AnuAlly under
You make these settings for one controller at a time.
To make maintenance mode settings:
1. At the command prompt, type net -a enable -f ipv6 -m -c 1 and press Enter to enable IPv6.
After a moment, the comand prompt reappears, indicating that your setting was successful.
administrator@cli>
2. At the command prompt, type net -a mod -m -c 1 -s " followed by:
• primaryip= and the IP address ,
• primaryipmask= and the subnet mask ,
• primarydns= and the DNS server IP address ,
• gateway= and the Gateway server IP address
" and press Enter .
Example:
administrator@cli> iscsi -a mod -t portal -s
"primaryip=2001:0db8:85a3:0000:0000:8a2e:0370:7336, primaryipmask=2001:0db8:
fedc:ba98:7654:3210:0246:8acf,
primarydns=2001:0db8:85a3:0000:0000:8a2e:0370:7001,
gateway=2001:0db8:85a3:0000:0000:8a2e:0370:7002"
After a moment, the comand prompt reappears, indicating that your setting was successful.
administrator@cli>
DS300f G2 Series User Manual
iP 6
v