Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - QUALITY OF SERVICE CONFIGURATION GUIDE 2010-09-22 Configuration Manual page 203

Copyright © 2010, Juniper Networks, Inc.
Chapter 20: Configuring QoS for Gigabit Ethernet Interfaces and VLAN Subinterfaces
DEBUG 06/17/2007 14:50:19 radiusSendAttributes: ACCESS-REQUEST attributes
(default)
DEBUG 06/17/2007 14:50:19 radiusSendAttributes:
vlan@test
DEBUG 06/17/2007 14:50:19 radiusSendAttributes:
GigabitEthernet 2/1.100:100:0004194348
DE BUG 06/17/2007 14:50:19 radiusSendAttributes:
<value withheld>
DEBUG 06/17/2007 14:50:19 radiusSendAttributes:
#ananke#E21#100
DEBUG 06/17/2007 14:50:19 radiusSendAttributes:
15
DEBUG 06/17/2007 14:50:19 radiusSendAttributes:
553648228
DEBUG 06/17/2007 14:50:19 radiusSendAttributes:
GigabitEthernet 2/1.100:100
DEBUG 06/17/2007 14:50:19 radiusSendAttributes:
172.26.27.50
DEBUG 06/17/2007 14:50:19 radiusSendAttributes:
ananke
DEBUG 06/17/2007 14:50:19 radiusAttributes: USER ATTRIBUTES: (vlan@test)
DEBUG 06/17/2007 14:50:19 radiusAttributes:
DEBUG 06/17/2007 14:50:19 radiusAttributes: total eap message attr length = 0
DEBUG 06/17/2007 14:50:19 radiusAttributes:
DEBUG 06/17/2007 14:50:19 radiusAttributes:
attr: test
DEBUG 06/17/2007 14:50:19 radiusAttributes:
attr: 1
DEBUG 06/17/2007 14:50:19 radiusAttributes:
test
DEBUG 06/17/2007 14:50:19 radiusAttributes:
attr: 1
DEBUG 06/17/2007 14:50:19 radiusAttributes:
DEBUG 06/17/2007 14:50:19 radiusAttributes:
Verify that the interface was created in the default virtual router.
6.
host1:server# show ip interface brief
Interface
-------------------- -------------------
null0
loopback0
GigabitEthernet6/0.100 Unnumbered
Verify that the framed route is installed.
7.
host1:server# show ip route
Prefix/Length Type
------------------ --------- --------------- ---------- -----------------------
10.1.0.0/24 Connect
40.40.41.0/30 Access 0.0.0.0
TIP: When you initially create the user record for dynamic IP interfaces
using VSA [22], you might not know the next hop. In this case, specify the
value 0.0.0.0 for the next hop. The E Series router then assigns the
subinterface associated with the user as the next hop in the routing table.
Verify that the correct QoS profile is attached to the VLAN subinterface.
8.
acct-session-id attr added: erx
calling-station-id attr added:
class attr: (binary data)
framed route attr: 40.40.41.0/30 0.0.0.0
ingress policy name (vsa)
ingress policy stats (vsa)
egress policy name (vsa) attr:
egress policy stats (vsa)
qos profile name (vsa) attr: test
virtual router name (vsa) attr: server
IP-Address Status
---------- ---------- -------------
255.255.255.255/32 up
10.1.0.1/24 up
up up
Next Hop Dst/Met
10.1.0.1 0/0
3/2 GigabitEthernet6/0/0.100
username attr added:
user-password attr added:
nas-port-type attr added:
nas-port attr added:
nas-port-id attr added:
nas-ip-address attr added:
nas-identifier attr added:
Protocol Description
up
up
Interface
loopback0
173