Juniper BGP - CONFIGURATION GUIDE V 11.1.X Configuration Manual page 738

JUNOSe 11.1.x BGP and MPLS Configuration Guide
tunnel endpoint
announcement............................................220
definition.....................................................218
tunnel metric for backup.....................................243
tunnel models for differentiated services............258
ultimate hop popping..........................................211
upstream node....................................................218
VPI/VCI and labels...............................................213
VPLS, configuring LSPs for..................................599
VPNs
BGP/MPLS....................................................382
weight.................................................................243
See also layer 2 services over MPLS; LDP; RSVP-TE
mpls commands........................................................269
mpls...........................................269, 274, 599, 665
mpls atm vci range.............................................274
mpls atm vpi range.............................................274
mpls backup-path...............................................289
mpls bandwidth..................................................275
mpls classifier-list................................................307
mpls create-dynamic-interfaces..................220, 269
mpls diff-serv phb-id traffic-class........................307
mpls disable........................................................274
mpls explicit-path...............................................280
mpls ip propagate-ttl...........................................269
mpls l2-transport load-balancing-group...............542
mpls lsp no-route retries.....................................272
mpls lsp no-route retry-time...............................272
mpls lsp retries...................................................272
mpls lsp retry-time..............................................269
mpls policy.........................................................538
mpls policy-list....................................................307
mpls reoptimize..................................................272
mpls reoptimize timers frequency......................272
mpls set-exp-bits.................................................303
mpls statistics label.............................................317
mpls statistics next-hop......................................318
mpls topology-driven-lsp.....................................270
mpls traffic-class.................................................308
mpls traffic-eng administrative-weight................275
mpls traffic-eng attribute-flags............................275
mpls traffic-eng flooding threshold.....................275
mpls traffic-eng link-management timers
periodic-flooding.............................................272
mpls tunnel-model..............................................258
mpls tunnels profile............................................277
mpls-relay...........................531, 532, 534, 537, 538
mpls-relay atm cell-packing mcpt-timers ...........526
mpls-relay atm vpi-range
....................................................................526
See also show mpls commands
MPLS echo reply packets
testing network connectivity
for egress nodes in point-to-multipoint
LSPs.........................................................237
702
Index
MPLS echo request packets
testing network connectivity
for egress nodes in point-to-multipoint
LSPs.........................................................237
MPLS echo requests
excluding P2MP Responder Identifier TLV from
responses sent from all nodes in the path to
ingress.....................................................240
including P2MP Responder Identifier TLV in
tracing the path from ingress node..............240
inclusion of sub-TLVs of P2MP Responder
Identifier TLV in
IPv4 Egress Address P2MP Responder
Identifier..................................................240
IPv4 Node Address P2MP Responder
Identifier..................................................240
IPv6 Egress Address P2MP Responder
Identifier..................................................240
IPv6 Node Address P2MP Responder
Identifier..................................................240
sent to nodes other than egress nodes in MPLS
LSPs
echo response to originator.........................238
specifying
a delay for echo responses..........................239
without P2MP Responder Identifier TLV contained
echo response to originator.........................238
MPLS echo responses
containing Echo Jitter TLV
no action performed in connectivity
verification...............................................239
controlled by Response Type filed in
requests..........................................................241
delaying sending of
preventing discarding, owing to rate
limiting....................................................239
preventing flooding at originator.................239
dependence on position of node
in point-to-multipoint LSPs..........................241
sent from a particular egress node
specified in the P2MP Responder Identifier
TLV .........................................................240
sent from all nodes in the path to ingress
with P2MP Responder Identifier TLV excluded
in requests...............................................240
MPLS L2VPN over LAG
configuration example........................................551
MPLS L2VPN over VLAN over LAG
configuration example........................................547
MPLS L2VPNs
over LAG, configuration example........................551
over VLAN over LAG, configuration
example..........................................................547
MPLS L2VPNs over LAG
on CE-side, overview..........................................521