Table of Contents
Advertisement
1
NOTES:
1.
VERIFY THAT PULLEY SPINS AND SLIDES FREELY ON DOWEL PIN.
2.
APPLY LOCTITE (C07246) TO DOWEL PIN, PRESS INTO PLACE, DO NOT ALLOW LOCTITE TO CONTACT BEARING.
3.
THREAD CABLE THROUGH POST, CREATE A KNOT TO RETAIN AXIALLY, PULL KNOT INTO POST.
4.
USING COMPRESSION FITTING, CREATE 1-INCH LOOP IN END OF CABLE. CRIMP FERRULE TO CREATE LOOP. TEST CRIMP WITH 1000g
WEIGHTS. OVERALL ASSEMBLED CABLE LENGTH TO BE APPROXIMATELY 10-INCHES.
5.
APPLY LOCTITE (C07246)TO CENTERING PIN. PRESS INTO PLACE UNTIL SHOULDERING.
D
6.
APPLY EPOXY (C11805)TO SET SCREW. SCREW INTO THE END OF THE POST WITH 0.13-INCH EXTENDING FROM END. DO NOT ALLOW EPOXY
TO FILL THE EXPOSED THREADS.
7.
PLACE ALL COMPONENTS AND WEIGHT CERTIFICATES IN A BOX. LABEL WITH PART NUMBER AND ASSEMBLY NAME.
C
B
A
1
2
3
8
7
6
KNOT
3
2
2
3
4
J
1
4
5
ITEM
1
2
3
4
5
6
7
8
9
H
10
BREAK EDGES, DEBURR
THIS DOCUMENT AND THE DRAWINGS AND
TECHNICAL DATA CONTAINED HEREON ARE THE
UON DIMS ARE IN INCHES
PROPERTY OF CHANDLER ENGINEERING COMPANY
LLC. REPRODUCTION OR DISSEMINATION IN ANY
1 PLC
0.030
2 PLC
FORM EXCEPT AS EXPRESSLY AUTHORIZED BY THE
3 PLC
0.005
ANGL
OWNER IS FORBIDDEN. THE HOLDER AGREES TO
SURFACE FINISH 63 RMS
RETURN THE DOCUMENT TO THE OWNER ON
DEMAND. COPYRIGHT BY CHANDLER ENGINEERING
THIRD ANGLE PROJECTION
COMPANY LLC
4
5
t
DESCRIPTION
ECN T7159; DELETE C16183 1000 WEIGHT,
ADD P-1351-CERT AND P-1352-CERT
G
WEIGHT AND HANGER. LENGTHEN CABLE
TO 10-IN. LENGTHEN 5265MX-0055
ECN T7642; DELETE P-1351-CERT AND P-
H
1352-CERT. ADD C17538-CERT AND C17539-
CERT
ECN T8566; CLARIFIED FASTENING OF SET
J
SCREW USING EPOXY
PART NUMBER
DESCRIPTION
5265MX-0055
HOUSING, CALIBRATOR
R-0695
FTG,COMPRESSION,0.024 GA
R-0696
CABLE,SST,0.024,2018-SN,NYL CT
C15559
PIN,DOWEL,SS,0.125X1.125L
C15558
PULLEY,IDLER,0.500X0.125
5265MX-0064
PIN, CALIBRATOR CENTERING
5265MX-0057
POST, CALIBRATOR
H-6008
SCREW,SKHSS,SS,6-32X0.250,CUP
C17538
WEIGHT,SET,BAL,SLTD,METRIC,SS,CERT
C17539
HANGER,WEIGHT,50GRM,CERT
CHANDLER ENGINEERING
DRAWN: JJM
1/20/2014
MFG: JBG
1/20/2014
0.010
ENGR: JJM
1/20/2014
CALIBRATOR ASSEMBLY, 5265MX
1/2
TYPE:
PN: 5265MX-0056
STRUCT:
PROJ: 5265MX
5
6
DATE
APPROVED
3/29/2016
JJM
4/6/2017
JJM
D
6/10/2019
JJM
C
B
QTY
1
1
0.83
1
1
1
1
A
1
1
1
REV J
SIZE B
SHEET 1 OF 1
6
TITLE BLOCK REV 3
Advertisement
Table of Contents
