Da16600 Evb Ver 4.0; Table 21: Da16600 Evb Switch Description - Renesas FreeRTOS DA16200 User Manual

UM-WI-056
DA16200 DA16600 FreeRTOS Getting Started Guide
DA16600 EVB includes several switches, see description f or each switch below.

Table 21: DA16600 EVB Switch Description

Switch Pin Relevant pin
SW3 1 DA16200
2
SW4 1 DA14531
2
3
4
SW5 1 DA16200
2
SW6 1 DA14531
2
SW7 1 DA16200
2
3
4
SW8 1 DA16200
2
SW9 1 DA16200
2 DA14531
SW10 1 DA14531
2
The current consumption can be measured at jumpers P1 and P2 with current measuring equipment.
See Section 6.5 f or details on the test setup.
When DA16600 EVK Pro is used f or measuring current consumption, remove jumpers P1 and P2
and set pins 1 and 2 of SW9 to the ON position.
To measure the current consumption of DA16200, remove the jumper on P2 and turn ON pin1 of
SW9. To measure the current consumption of DA14531, remove the jumper on P1 and turn ON pin2
of SW9. The current consumption of the DA16200 and the DA14531 can be measured
simultaneously.
For more inf ormation on the DA16600 EVB, see the DA16600 DEVKT Electric Schematic Ref . [10].
A.4

DA16600 EVB Ver 4.0

Figure 66 shows the hardware conf iguration of the DA16600 EVB.
User Manual
CFR0012
UART0_RXD Connects FT232H to UART0_RXD
UART0_TXD Connects FT232H to UART0_TXD
P0_8 Connects FT2232H to P0_8 (UART_RXD)
P0_9 Connects FT2232H to P0_9 (UART_TXD)
P0_2 Enables Keil toolchain debug of DA14531
(SWCLK)
P0_10 Enables Keil toolchain debug of DA14531
(SWDIO)
GPIOC6 Connects FT2232H to UART2_TXD
GPIOC7 Connects FT2232H to UART2_RXD
P0_5 Connect FT2232H to P0_5 (1-wire UART)
Connect FT2232H to P0_5 (1-wire UART)
GPIOA6 Not available on DA16600 EVB V5.0
GPIOA7
GPIOA8
GPIOA9
GPIOA6 WPS
GPIOA7 Factory Reset
Measuring Enables to measure current consumption
current of DA16200 with EVK Pro.
consumption
Need to remove jumper P2.
Measuring Enables to measure current consumption
current of DA14531 with EVK Pro.
consumption
Need to remove jumper P1.
P0_6 Manual control of the internal RF SPDT.
Pin1 OFF & Pin2 OFF: internally controlled.
Pin1 ON & Pin2 OFF: DA14531 RF path ON
Pin1 OFF & Pin2 ON: DA16200 RF path ON
Revision 1.8
80 of 106
ON
NC
External pin-out
(J2/J3) only
External pin-out
(J2/J3) only
External pin-out
(J2/J3) only
External pin-out
(J2/J3) only
External pin-out
(J2/J3) only
Normal operation /
Need to connect
P2
Normal operation /
Need to connect
P1
© 2023 Renesas Electronics
OFF Default
ON
OFF
ON
OFF
OFF
ON
OFF
OFF
Aug. 18, 2023