B: Application; B1: Operation Mode Selection - YASKAWA CR700 Technical Manual

10.5

b: Application

b1: Operation Mode Selection

◆
No.
Name
(Hex.)
b1-01 Frequency Reference
Selection 1
(0180)
b1-02 Run Command Selection
1
(0181)
b1-03 Stopping Method
Selection
(0182)
b1-04 Reverse Operation
Selection
(0183)
b1-05 Operation Below
Minimum Freq
(0184)
b1-06 Digital Input Reading
(0185)
b1-14 Phase Order Selection
(01C3)
b1-15 Frequency Reference
Selection 2
(01C4)
b1-16 Run Command Selection
2
(01C5)
b1-17 Run Command at Power
Up
(01C6)
YASKAWA SIEPC71061723A YASKAWA AC Drive CR700 Technical Manual
Description
V/f CL-V/f OLV CLV AOLV
Sets the input method for the frequency reference.
0 : Keypad
1 : Analog Input
2 : Memobus/Modbus Communications
3 : Option PCB
V/f CL-V/f OLV CLV AOLV
Sets the input method for the Run command.
0 : Keypad
1 : Analog Input
2 : Memobus/Modbus Communications
3 : Option PCB
V/f CL-V/f OLV CLV AOLV
Sets the method to stop the motor after removing a Run command or entering a Stop
command.
Note:
When A1-02 = 3, 4 [Control Method Selection = CLV, AOLV], the setting range is
0, 1, 3.
0 : Ramp to Stop
1 : Coast to Stop
2 : DC Injection Braking to Stop
3 : Coast to Stop with Timer
V/f CL-V/f OLV CLV AOLV
Sets the reverse operation function.
0 : Reverse Enabled
1 : Reverse Disabled
V/f CL-V/f OLV CLV AOLV
Sets the operation to perform when the frequency reference falls below the value set in
E1-09 [Minimum Output Frequency].
0 : Operate at Frequency Reference
1 : Coast to Stop
2 : Operate at Minimum Frequency
3 : Operate at Zero Speed
V/f CL-V/f OLV CLV AOLV
Sets the number of times that the drive reads the sequence input command to prevent
malfunction because of electrical interference.
0 : Single Scan
1 : Double Scan
V/f CL-V/f OLV CLV AOLV
Sets the phase order for output terminals U/T1, V/T2, and W/T3. This parameter can
align the Forward Run command from the drive and the forward direction of the motor
without changing wiring.
0 : Standard
1 : Switch Phase Order
V/f CL-V/f OLV CLV AOLV
Sets the input method for frequency reference 2.
0 : Keypad
1 : Analog Input
2 : Memobus/Modbus Communications
3 : Option PCB
V/f CL-V/f OLV CLV AOLV
Sets the input method for Run Command 2 when the user switches the control circuit
terminals ON/OFF to change the Run command source.
0 : Keypad
1 : Analog Input
2 : Memobus/Modbus Communications
3 : Option PCB
V/f CL-V/f OLV CLV AOLV
Sets drive response when the CPU changes from de-energized to energized and there is
an active Run command. Set this parameter in applications where energizing or de-
energizing the drive enables the Run command.
0 : Disregard Existing RUN Command
1 : Accept Existing RUN Command
10.5 b: Application
Default
Ref.
(Range)
0 584
(0 - 3)
1 585
(0 - 3)
0 586
(0 - 3)
0 588
(0, 1)
0 589
(0 - 3)
1 590
(0, 1)
0 590
(0, 1)
0 590
(0 - 3)
0 592
(0 - 3)
0 592
(0, 1)
471
10