Daikin VRV III Manual page 96

ED34-862
KDBH55K160(F) — Sealing Material of Air Discharge Outlet
KDBH55K160
Blow Direction Selection and Sealing Material Mounting
(1) Blow direction selection
Depending on the installation location, select a blow direction from the table below. For the setting position number, refer to
For the selection of installation location, refer to the installation manual attached to the indoor unit's main body.
Precautions
Blow direction patterns other than those shown in the figure below cannot be selected. (Condensation may occur.)
Air outlet B1, B2
Air outlet 2
Air outlet A
Air outlet 1
Air outlet D
Pipe side
3 3
4
2 2
1 1
(2) Matching with the corner air outlets A to D that are to be blocked, stick the sealing material to the tape for fixing the sealing material.
(Stick the sealing material so that the sealing material comes to the positions shown in the schematic diagram.)
Sealing material 2
Release paper
2
Procedure 1
Remove the
release paper.
Tape for fixing the sealing material
Procedure 2
Air outlet A
Stick the sealing material to the
tape for fixing the sealing material.
With air outlets B to D , using the same procedure,
stick the sealing material to the tape for fixing the sealing material as shown in the figure.
The sealing material has a directional property. Be sure to stick the sealing material to the tape for fixing the sealing material so that the printed number of outlet to be blocked becomes visible.
Precautions
When blocking both the air outlet 1 and air outlet D , start the sticking of sealing material with the air outlet D .
(4) Matching the longitudinal air outlet numbered 1 to 4 that are to be blocked, prepare the sealing material and tape for fixing the sealing material.
Cut both the sealing material and tape for fixing the sealing material along the perforation (dotted line).
Stick the sealing material to the tape for fixing the sealing material.
(Stick so that the sealing material comes to the centre of tape for fixing the sealing material.)
Example) When blocking air outlet 2 or 3
Procedure 2
Remove the
release paper.
Release paper
Procedure 3
<Sealing material treatment>
Stick the sealing material so that it comes
to the centre of tape for fixing the sealing material.
• When blocking the air outlet 1 , the sealing material preparation is not necessary.
The sealing material has a directional property. Be sure to stick the sealing material to
Precautions
the tape for fixing the sealing material so that the printed number of outlet to be blocked becomes visible.
FXFQ-P
Dimensions
Sealing materials for long air outlets (Polyethylene foam t10): 2 pieces
Slit
Sealing materials for air outlets at the corner (Polyethylene foam t10): 1 piece for each
Tape for sealing materials
for long air outlets (Non-woven fabric t0.6): 2
Slit
Side insulation plate (NB foam t10) : 2
Antisweat material (Flocking tape): See right
Antisweat material (Flocking tape): See right
3 3
Air outlet 3
2 4 2
Air outlet C
1 1
4-way
3 3
2
2 4
Drain side
1 1
3 3
Air outlet 4
2 4
2
1 1
2-way
3 3 3
2
4 2 4 2 4
1 1 1
Sealing material 3
Tape for fixing the sealing material 8
Air outlet B1
( When the indoor unit's main )
body belongs to classes 28 to 56
8
Sealing material 5
Tape for fixing the sealing material 8
Air outlet C
Sealing material 1
Procedure 1
Cut off
3
Tape for fixing the sealing material 7
Tape for sealing materials
for air outlets at the corner (Non-woven fabric t0.6): 3
Applicable part number Q'ty and colour
4, grey
4 for each, Dark grey or black
Applicable part number Q'ty and colour
4, grey
4 for each, Dark grey or black
Field Setting .
4-way
3 3 3
4 2 2 4 2
4
1 1 1
3-way
3 3 3
4 2 2 4 2
4
1 1 1
3-way 2-way
3 3 3
2
4 2 4 2 4
1 1 1
3 3 3
4 2 4
2 4 2
1 1 1
Sealing material 4
Tape for fixing the sealing material 8
Air outlet B2
( When the indoor unit's main body )
belongs to classes 63 to 160
Sealing material 6
Tape for fixing the sealing material 9
Air outlet D
: http://splitoff.ru/tehn-doc.html
Accessories
Unit:mm
Sealing materials for horizontal blades (Polyethylene foam t10): 8 pieces
Tape for sealing materials
for air outlets at the corner (Non-woven fabric t0.6): 1
4
4
4
4
(3) Stick the sealing material that was prepared in
(2) to the air outlet of indoor unit main body.
Air outlet
Indoor unit main body
(5) Stick the sealing material that was prepared in
(4) to the air outlet of indoor unit main body.
Indoor unit main body
Air outlet 1
<Mounting to air outlet>
J : 1P177350A
2
91