Terex Genie GTH-4013 Operator's Manual page 41

OPERATING INSTRUCTIONS
C-1 PRE-OPERATION INSPECTION ............ C-2
C-2 ENTERING THE MACHINE .................... C-4
C-2.1 Entering the cab ..................................... C-4
C-2.1.1 Emergency exit-way ............................... C-4
C-2.2 Adjusting the seat .................................. C-5
C-2.3 Fastening the seat belts ......................... C-5
C-2.4 Adjusting the steering column ................ C-6
C-2.5 Adjusting the rear view mirrors .............. C-6
C-2.6 Switching on the cab interior lamp ........ C-6
C-3 DRIVING PLACE ..................................... C-7
C-3.1 Controls and instruments ....................... C-7
C-3.2 Engine controls and instruments ........... C-9
C-3.2.1 Ignition switch ........................................ C-9
C-3.2.2 Forward/reverse gear switch .................. C-9
C-3.2.3 Turn signals - windscreen wiper -
lights - horn switch ............................... C-10
C-3.2.4 Brakes .................................................. C-11
C-3.2.5 Accelerator control ............................... C-11
C-3.2.6 Gearbox controls .................................. C-12
C-3.2.7 Steering mode selection ...................... C-12
C-3.2.8 Cab/road/platform changeover switch .. C-12
C-3.2.9 Auxiliary drive controls ......................... C-13
C-3.3 Instruments and warning lights ............ C-14
C-3.3.1 Instruments .......................................... C-14
C-3.3.2 Warning lights ...................................... C-15
C-3.4 Control lever ......................................... C-16
C-3.4.1 Function selection ................................ C-17
C-3.4.2 Emergency stop ................................... C-18
C-3.4.3 Disabling the overload warning system . C-18
C-3.4.4 Lifting/lowering the boom .................... C-19
C-3.4.5 Extending/retracting the boom ............ C-20
C-3.4.6 Pitching the attachment holding frame
forward/back ........................................ C-21
C-3.4.7 Quick-coupling the attachments .......... C-22
C-3.5 Machine sway control .......................... C-23
C-3.6 Outrigger control .................................. C-24
C-3.7 Manual controls .................................... C-25
Handler with telescopic boom GTH-4013
OPERATING INSTRUCTIONS
Section
TABLE OF CONTENTS
C-4
C-4.1
C-4.1.1 Checks at the machine start-up ........... C-26
C-4.2
C-4.3
C-4.4
C-4.5
C-4.6
C-4.7
C-5
C-5.1
C-5.2
C-5.2.1 Description of the controls ................... C-32
C-5.2.2 Operation ............................................. C-32
C-5.2.2 Alarm codes and resetting ................... C-33
C-5.3
C-5.3.1 Adjusting the forks ............................... C-34
C-5.3.2 Working phases ................................... C-35
C-5.4
C-6
C-6.1
C-6.1.1 Setting the gear lever in neutral ........... C-38
C-6.1.2 Dismantling the Cardan shaft ............... C-39
C-6.2
C-6.3
C-6.4
C-6.5
C-6.5.1 Short inactivity ...................................... C-42
C-6.5.2 Machine storage................................... C-42
C-6.6
C-6.6.1 Cleaning instructions ............................ C-43
C-6.6.2 Washing instructions ............................ C-43
C-6.7
C-6.7.1 Disposal of batteries ............................ C-43
C-1
Page
Document 57.0007.0200 - 01/2006
C
SETUP .................................................. C-26
Before starting the engine .................... C-26
Starting the engine ............................... C-26
Jump-starting the engine ..................... C-27
Low temperature starting ..................... C-28
Starting the machine ............................ C-29
Use of the man-platform ...................... C-29
Stopping and parking the machine ...... C-30
USING THE HANDLER ......................... C-30
Using the load charts ........................... C-31
Load limiter........................................... C-32
Handling loads ..................................... C-34
Changing the optional attachment ....... C-36
TRANSPORTING THE MACHINE ........ C-38
Moving a disabled machine ................. C-38
Road or site transfer ............................. C-40
Lifting the machine ............................... C-41
Transporting the machine on other
vehicles ................................................ C-41
Parking and storage ............................. C-42
Cleaning and washing the machine ..... C-43
Machine disposal ................................. C-43