Relative Humidity; Vibration; Shock; Degree Of Protection - B&R Automation PC 2200 User Manual

Technical data

2.2.3.2 Relative humidity

The following table shows the minimum and maximum relative humidity (non-condensing) of the individual com-
ponents that are relevant for limiting the humidity of the complete system. Always use the lowest and the highest
common value for the determination.
Component Model number
System unit 5APC2200.ALxx-000
5CFAST.xxxx-00
5CFAST.032G-10 ≥ Rev. G0
5CFAST.064G-10 ≥ Rev. E0
5CFAST.128G-10 ≥ Rev. E0
CFast card
5CFAST.256G-10
5CFAST.032G-10 ≤ Rev. F0
5CFAST.064G-10 ≤ Rev. D0
5CFAST.128G-10 ≤ Rev. D0
5ACCLI01.SDL0-000
Monitor/Panel option
5ACCLI03.SDL4-000
5ACCIF01.FPCC-000
5ACCIF01.FPCS-000
5ACCIF01.FPLK-000
5ACCIF01.FPLS-000
5ACCIF01.FPLS-001
Interface option
5ACCIF01.FPSC-000
5ACCIF01.FPSC-001
5ACCIF01.FSS0-000
5ACCIF01.ICAN-000
5ACCIF03.CETH-000
Table 12: System units, monitor/panel options, IF options, CFast cards - Relative humidity
The values listed correspond to the relative humidity (non-condensing) at an ambient temperature of 30°C. For
more detailed information about the specified relative humidity as a function of temperature, see the technical data
of the individual components.

2.2.3.3 Vibration

The following table provides an overview of the maximum vibration values of the complete system. Limitations are
possible due to individual components.
Automation PC
With CFast card
With CFast card and cable strain relief clip
1) Testing is performed per EN 60068-2-6.
2) The specification refers to a device in its original packaging.

2.2.3.4 Shock

The following table provides an overview of the maximum shock values of the complete system. Limitations are
possible due to individual components.
Automation PC
With CFast card
1) Testing is performed per EN 60068-2-27.
2) The specification refers to a device in its original packaging.

2.2.3.5 Degree of protection

Under the following conditions, the Automation PC 2200 offers IP20 protection per EN 60529:
• Correct installation of the Automation PC 2200 (see
• Installation of all covers or components on interfaces and slots
• Compliance with all ambient conditions
30
Operation
5 to 90%
Max. 85% at 85°C
Max. 85% at 85°C
Max. 85% at 85°C
Max. 85% at 85°C
Max. 85% at 85°C
10 to 95%
10 to 95%
10 to 95%
5 to 90%
5 to 90%
5 to 90%
5 to 90%
5 to 90%
5 to 90%
5 to 90%
5 to 90%
5 to 90%
5 to 90%
5 to 90%
5 to 90%
Operation
1)
Continuous Periodic
2 to 9 Hz: 2 to 9 Hz:
1.75 mm amplitude 3.5 mm amplitude
9 to 200 Hz: 0.5 g 9 to 200 Hz: 1 g
2 to 9 Hz: 2 to 9 Hz:
3.5 mm amplitude 7.0 mm amplitude
9 to 200 Hz: 1 g 9 to 200 Hz: 2 g
Table 13: Vibration
Operation
1)
15 g, 11 ms
Table 14: Shock
Automation PC 2200 User's manual V 1.05 Translation of the original documentation
Storage
5 to 95%
Max. 85% at 85°C
Max. 85% at 85°C
Max. 85% at 85°C
Max. 85% at 85°C
Max. 85% at 85°C
10 to 95%
10 to 95%
10 to 95%
5 to 95%
5 to 95%
5 to 95%
5 to 95%
5 to 95%
5 to 95%
5 to 95%
5 to 95%
5 to 95%
5 to 95%
5 to 95%
5 to 95%
Storage
1)2)
2 to 8 Hz: 7.5 mm amplitude
8 to 200 Hz: 2 g
200 to 500 Hz: 4 g
2 to 8 Hz: 7.5 mm amplitude
8 to 200 Hz: 2 g
200 to 500 Hz: 4 g
Storage
1)2)
30 g, 6 ms
"Installation" on page 122)
Transport
5 to 95%
Max. 85% at 85°C
Max. 85% at 85°C
Max. 85% at 85°C
Max. 85% at 85°C
Max. 85% at 85°C
10 to 95%
10 to 95%
10 to 95%
5 to 95%
5 to 95%
5 to 95%
5 to 95%
5 to 95%
5 to 95%
5 to 95%
5 to 95%
5 to 95%
5 to 95%
5 to 95%
5 to 95%
Transport
1)2)
2 to 8 Hz: 7.5 mm amplitude
8 to 200 Hz: 2 g
200 to 500 Hz: 4 g
2 to 8 Hz: 7.5 mm amplitude
8 to 200 Hz: 2 g
200 to 500 Hz: 4 g
Transport
1)2)
30 g, 6 ms