Resetting The Matrix; Restoring The Factory Default Settings; Querying The Operation Mode (Standby Mode) Of The Matrix; Switching To Standby Mode - Lightware MX2-4x4-HDMI20-CA User Manual


  
9. LW3 Programmers' Reference
9.4.4. Resetting the Matrix
The matrix can be restarted – the current connections (LAN, RS-232) will be terminated.
Command and Response #reset #reboot #restart
Ý CALL·/SYS:softReset()
Ü mO·/SYS:softReset=
Example
Ý CALL /SYS:softReset()
Ü mO /SYS:softReset=
9.4.5. Restoring the Factory Default Settings
The device is restarted, current connections are terminated, and the default settings are restored. See the
complete list in Factory Default Settings
Command and Response #factory
Ý CALL·/SYS:factoryDefaults()
Ü mO·/SYS:factoryDefaults=
Example
Ý CALL /SYS:factoryDefaults()
Ü mO /SYS:factoryDefaults=
9.4.6. Querying the Operation Mode (Standby Mode) of the Matrix
In standby mode, the video transmission is disabled, the LCD is switched off, but remote connections (LAN,
RS-232) remain available.
Command and Response #standby
Ý GET·/MANAGEMENT/POWER.Operation
pr·/MANAGEMENT/POWER.Operation=<op_mode>
Ü
Parameters
Identifier Parameter description
<op_mode> Operation mode of the matrix
Example
Ý GET /MANAGEMENT/POWER.Operation
Ü pr /MANAGEMENT/POWER.Operation=NORMAL
section.
Parameter values
NORMAL: The matrix operates normal mode, the video
transmission and the other functions are enabled.
STANDBY: The video transmission is disabled, but the
device is available remotely.
Applied firmware package: v1.7.0 | LDC software: v2.5.1b5
MX2-HDMI20 series – User's Manual
9.4.7. Switching to Standby Mode
In standby mode, the video transmission is disabled, the LCD is switched off, but remote connections (LAN,
RS-232) remain available.
Command and Response #standby
Ý CALL·/MANAGEMENT/POWER:standby()
Ü mO·/MANAGEMENT/POWER:standby=
Example
Ý CALL /MANAGEMENT/POWER:standby()
Ü mO /MANAGEMENT/POWER:standby=
9.4.8. Switching to Normal Mode
When the matrix is in Standby mode, it can be switched back to Normal mode as follows:
Command and Response
Ý CALL·/MANAGEMENT/POWER:wakeUp()
Ü mO·/MANAGEMENT/POWER:wakeUp=
Example
Ý CALL /MANAGEMENT/POWER:wakeUp()
Ü mO /MANAGEMENT/POWER:wakeUp=
9.5. Switching and Crosspoint Settings
INFO: The current setting can be queried by using the
9.5.1. Query the Video Crosspoint State
Command and Response #switch #crosspoint
Ý GET·/MEDIA/XP/VIDEO.DestinationConnectionStatus
pr·/MEDIA/XP/VIDEO.DestinationConnectionStatus=<out1_state>;<out2_state>;...;<out8_state>
Ü
Parameters
The <out#_state> parameters mean the output ports (O1, O2 etc.) one after the other. The value of the
parameter shows the input port switched to the given output port.
Example
Ý GET /MEDIA/XP/VIDEO.DestinationConnectionStatus
Ü pr /MEDIA/XP/VIDEO.
DestinationConnectionStatus=I1;I1;I1;I1;I1;I1;I1;I1;I1;I1;I1;I1;I1;I1;I1;I1;I1;I1;I1;I1;I1;I1;I1;I1;
I1 input port is connected to all output ports.
80
GET command.