Lightware MX2-4x4-HDMI20-CA User Manual page 99


  
9. LW3 Programmers' Reference
Setting the Conversion Mode
Ý SET·/MEDIA/PORTS/VIDEO/ <in>/SETTINGS.Conversion=<conversion_mode>
Restart Link Training
Ý CALL·/MEDIA/PORTS/VIDEO/ <in>/SETTINGS:dpLinkTrain()
Audio Input Port Settings
Audio Mode Setting
SET·/MEDIA/PORTS/VIDEO/<in>/ANALOGAUDIO.AudioMode=<audio_mode>
Ý
Analog Audio Input Level Settings
Setting the Balance (the Exact Value)
SET·/MEDIA/PORTS/VIDEO/<in>/ANALOGAUDIO.Balance=<bal_value>
Ý
Setting the Balance (by a Step Value)
Ý CALL·/MEDIA/PORTS/VIDEO/<in>/ANALOGAUDIO:stepBalance(<step_value>)
Setting the Mute State
SET·/MEDIA/PORTS/VIDEO/<in>/ANALOGAUDIO.Mute=<mute_state>
Ý
Setting the Gain
SET·/MEDIA/PORTS/VIDEO/<in>/ANALOGAUDIO.Gain=<gain_value>
Ý
Video Output Port Settings (HDMI and Displayport)
Querying the Status of the Output Ports
Ý GET·/MEDIA/XP/VIDEO.DestinationPortStatus
Muting an Output
Ý CALL·/MEDIA/XP/VIDEO:muteDestination(<out>)
Unmuting an Output
Ý CALL·/MEDIA/XP/VIDEO:unmuteDestination(<out>)
Locking an Output
Ý CALL·/MEDIA/XP/VIDEO:lockDestination(<out>)
Unlocking an Output
Ý CALL·/MEDIA/XP/VIDEO:unlockDestination(<out>)
Setting the HDCP Mode (Output Port)
SET·/MEDIA/PORTS/VIDEO/<On>/SETTINGS.HdcpMode=<HDCP_mode>
Ý
Setting the Audio Mode
SET·/MEDIA/PORTS/VIDEO/<out>/EMBEDDEDAUDIO.AudioMode=<audio_mode>
Ý
MX2-HDMI20 series – User's Manual
Sending an OSD String
SET·/MEDIA/PORTS/<out>/CEC.OsdString=<text>
Ý
Ý CALL·/MEDIA/PORTS/VIDEO/<out>/CEC:send(set_osd)
Sending a CEC Command in Text Format
Ý CALL·/MEDIA/PORTS/VIDEO/<out>/CEC:send(<command>)
Sending a CEC Command in Hexadecimal Format
Ý CALL·/MEDIA/PORTS/VIDEO/<out>/CEC:sendHex(<hex_command>)
HDMI Output Settings
Setting the Signal Type (HDMI mode)
SET·/MEDIA/PORTS/VIDEO/<out>/SETTINGS.ForcedSignalType=<sig_type>
Ý
Scrambling
SET·/MEDIA/PORTS/VIDEO/<out>/SETTINGS.ForcedScrambling=<scr_mode>
Ý
Setting the Signal Conversion Mode
SET·/MEDIA/PORTS/VIDEO/<out>/SETTINGS.Conversion=<conv_mode>
Ý
Displayport Output Settings
Enable DP Power
SET·/MEDIA/PORTS/VIDEO/<out>/SETTINGS.EnablePower=<enable_power>
Ý
Enable Forced Link Training
SET·/MEDIA/PORTS/VIDEO/<out>/SETTINGS.DpForcedMode=<forced_mode>
Ý
Set the Forced Lane Number
SET·/MEDIA/PORTS/VIDEO/<out>/SETTINGS.DpForcedLaneCount=<lane>
Ý
Set the Forced Link Data Rate
SET·/MEDIA/PORTS/VIDEO/<out>/SETTINGS.DpForcedLinkRate=<data_rate>
Ý
Setting the Swing / pre-emphasis
Ý SET·/MEDIA/PORTS/VIDEO/<out>/SETTINGS.DpForcedLaneLevel=<voltage_level>;<preemph_level>;
Restart Link Training
Ý CALL·/MEDIA/PORTS/VIDEO/<out>/SETTINGS:dpLinkTrain()
Applied firmware package: v1.7.0 | LDC software: v2.5.1b5
99