Table of Contents
Advertisement
aPPenDiX B PeRiPheRal CiRCuiT BOaRDS FOR S1C6F016
Notes: • When developing an S1C63003 application, the connector pins shown below should not be
connected to the target board.
40-pin CN1-1: No. 27–30 (P30–P33), No. 33–36 (P40–P43)
50-pin CN2-1: No. 15–20 (SEG10–SEG15), No. 23–30 (SEG16–SEG23),
50-pin LC1-1: No. 19–50 (SEG10–SEG41)
50-pin LC1-2: No. 1–2 (SEG42–SEG43)
• When developing an S1C63004 application, the connector pins shown below should not be
connected to the target board.
40-pin CN1-1: No. 33–36 (P40–P43)
50-pin CN2-1: No. 27–30 (SEG20–SEG23), No. 33–40 (SEG24–SEG31),
50-pin LC1-1: No. 29–48 (SEG20–SEG39)
• When developing an S1C63008 application, the connector pins shown below should not be
connected to the target board.
50-pin CN2-1: No. 39–40 (SEG30–SEG31), No. 43–46 (SEG32–SEG35)
50-pin LC1-1: No. 39–44 (SEG30–SEG35)
B.3
Downloading to S5u1C63000P6
Note: The S1C630 Series circuit data is available only for the S5U1C63000P6, and it cannot be down-
loaded to the previous S5U1C63000P1 board.
Downloading Circuit Data – when new iCe (S5u1C63000h2/S5u1C63000h6) is used
The S5U1C63000P6 board comes with the FPGA that contains factory inspection data, therefore the circuit data
for the model to be used should be downloaded. The following explains the downloading procedure.
(1) Remove the ICE (S5U1C63000H2/S5U1C63000H6) top cover and then set the DIP switch "IOSEL2" on the
S5U1C63000P6 board to the "E" position.
(2) Connect the ICE to the host PC. Then turn the host PC and ICE on.
(3) Invoke the debugger included in the assembler package (ver. 5 or later for the S5U1C63000H2, ver. 9 or later
for the S5U1C63000H6). For how to use the ICE and debugger, refer to the manuals supplied with the ICE
and assembler package.
(4) Download the circuit data file (.mot) corresponding to the model by entering the following commands in the
command window.
>XFER
>XFWR
<file name>
>XFCP
<file name>
* The downloading takes about 15 minutes in the S5U1C63000H2 or about 3 minutes in the
S5U1C63000H6.
aP-B-8
Table B.
2.4 S5U1C6F016P2 CN1 connector pin assignment
10-pin CN1 connector
No.
1 V
(= 3.3 V)
DD
2 V
(= 3.3 V)
DD
3 P50
4 P51
5 P52
6 P53
7 Cannot be connected
8 Cannot be connected
9 V
SS
10 V
SS
No. 33–40 (SEG24–SEG31), No. 43–46 (SEG32–SEG35)
No. 43–46 (SEG32–SEG35)
(erase all)
(download the specified file)*
(compare the specified file and downloaded data)
Seiko epson Corporation
Pin name
S1C63003/004/008/016 TeChniCal Manual
(Rev. 1.1)
Advertisement
Table of Contents
