Transition Networks SM TAT4X Series Web User Manual page 105

Managed gigabit ethernet poe+ switch
Hide thumbs Also See for SM TAT4X Series:
Table of Contents

Advertisement

Transition Networks 
SMAC Source MAC address: xx‐xx‐xx‐xx‐xx‐xx or 'Any'.   
Tag: Value of Tag field can be 'Untagged', 'Tagged', 'C‐Tagged', 'S‐Tagged' or 'Any'. 
VID: Valid value of VLAN ID can be any value in the range 1‐4095 or 'Any'; you can enter either a specific value or 
a range of VIDs. 
PCP: Valid value PCP are specific (0, 1, 2, 3, 4, 5, 6, 7) or range (0‐1, 2‐3, 4‐5, 6‐7, 0‐3, 4‐7) or 'Any'. 
DEI: Valid value of DEI can be '0', '1' or 'Any'. 
Inner Tag: Value of Inner Tag field can be 'Untagged', 'Tagged', 'C‐Tagged', 'S‐Tagged' or 'Any'.   
Inner VID: Valid value of Inner VLAN ID can be any value in the range 1‐4095 or 'Any'; user can enter either a 
specific value or a range of VIDs. 
Inner PCP: Valid value of Inner PCP are specific (0, 1, 2, 3, 4, 5, 6, 7) or range (0‐1, 2‐3, 4‐5, 6‐7, 0‐3, 4‐7) or 'Any'. 
Inner DEI: Valid value of Inner DEI can be '0', '1' or 'Any'. 
Frame Type: Frame Type can have any of the following values: Any, EtherType, LLC, SNAP, IPv4, or IPv6 as 
described below: 
1. Any: Allow all types of frames. 
2. EtherType: Ether Type Valid Ether Type can be 0x600‐0xFFFF excluding 0x800(IPv4) and 0x86DD(IPv6) or 'Any'. 
3. LLC: Can be any of the following: 
DSAP Address: Valid DSAP(Destination Service Access Point) can vary from 0x00 to 0xFF or 'Any'. 
SSAP Address: Valid SSAP(Source Service Access Point) can vary from 0x00 to 0xFF or 'Any'. 
Control: Valid Control field can vary from 0x00 to 0xFF or 'Any'. 
4. SNAP: PID Valid PID(a.k.a Ether Type) can be 0x0000‐0xFFFF or 'Any'. 
5. IPv4: Can be any of the following: 
Protocol: IP protocol number: (0‐255, 'TCP' or 'UDP') or 'Any'. 
Source IP: Specific Source IP address in value/mask format or 'Any'. IP and Mask are in the format x.y.z.w 
where x, y, z, and w are decimal numbers between 0 and 255. When Mask is converted to a 32‐bit binary 
string and read from left to right, all bits following the first zero must also be zero.   
Destination IP: Specific Destination IP address in value/mask format or 'Any'. 
IP Fragment: IPv4 frame fragmented option: 'Yes', 'No' or 'Any'. 
DSCP: Diffserv Code Point value (DSCP): It can be a specific value, range of values or 'Any'. DSCP values 
are in the range 0‐63 including BE, CS1‐CS7, EF or AF11‐AF43. 
Sport: Source TCP/UDP port:(0‐65535) or 'Any', specific or port range applicable for IP protocol UDP/TCP. 
Dport: Destination TCP/UDP port:(0‐65535) or 'Any', specific or port range applicable for IP protocol 
UDP/TCP. 
6. IPv6: Can be any of the following: 
Protocol: IP protocol number: (0‐255, 'TCP' or 'UDP') or 'Any'. 
Source IP: 32 LS bits of IPv6 source address in value/mask format or 'Any'.   
Destination: IP Specific Destination IP address in value/mask format or 'Any'. 
DSCP: Diffserv Code Point value (DSCP): It can be a specific value, range of values or 'Any'. DSCP values 
are in the range 0‐63 including BE, CS1‐CS7, EF or AF11‐AF43. 
Sport: Source TCP/UDP port:(0‐65535) or 'Any', specific or port range applicable for IP protocol UDP/TCP. 
Dport: Destination TCP/UDP port:(0‐65535) or 'Any', specific or port range applicable for IP protocol 
UDP/TCP. 
33786 Rev. A
 
https://www.transition.com
SMxxTAT4Xx Web User Guide 
Page 105 of 340

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SM TAT4X Series and is the answer not in the manual?

This manual is also suitable for:

Sm48tat4xa-rpSm24tat4xb

Table of Contents