Anyone using this product in such an application without express written consent of an officer of Transition Networks does so at their own risk, and agrees to fully indemnify Transition Networks for any damages that may result from such use or sale.
(SM24TAT2DPA) in the “Search” box at our website at https://www.transition.com. For Transition Networks Drivers, Firmware, Manual, etc. go to the Product Support webpage (no logon required). For Transition Networks Application Notes, Brochures, Data Sheets, Specifications, etc. go to the Support Library (no registration required). 33702 Rev. A https://www.transition.com...
This manual describes hardware installation and basic troubleshooting for these managed switches. Front Panel The SM24TAT2DPA switch front panel has system and port LEDs for installation and troubleshooting and the Mode/Reset button. The SM24TAT2DPA front panel is shown and described below.
Page 6
Transition Networks SM24TAT2DPA Install Guide Mode LEDs The Mode LEDs indicate the mode of all RJ45/SFP ports on the switch. You can press the Mode/Reset button sequentially to switch between the two different modes (Link/Activity/Speed mode and PoE mode). Color...
Transition Networks SM24TAT2DPA Install Guide The port has no active network cable connected, or it is not established a link to connected device. Otherwise, the port may have been disabled through the switch user interface. When PoE Mode LED Lit...
Transition Networks SM24TAT2DPA Install Guide Back Panel The SM24TAT2DPA back panel is shown below. 33702 Rev. A https://www.transition.com Page 8 of 23...
After firmware upgrade, switch automatically moves configuration to latest firmware version. Warning: this case must be grounded. No DC input may be grounded. The SM24TAT2DPA is compliant with 802.3at in Environment A when using an isolated power supply. For 802.3at Environment B applications, use mid-span injector (s), e.g.
Transition Networks SM24TAT2DPA Install Guide Mounting the Switch in a 19-inch Rack Step1. Attach the mounting brackets to both sides of the chassis with screws. Figure 4 Attaching mounting brackets to the switch Step2. Place the switch on a rack shelf in the rack. Push the switch in until the oval holes in the brackets align with the mounting holes in the rack posts.
Transition Networks SM24TAT2DPA Install Guide Mounting the Switch on Desk or Shelf Step1. Verify that the workbench is sturdy and reliably grounded. Step2. The rubber feet are included in the accessory kit. Attach the four adhesive rubber feet to the bottom of the switch.
Stop bit—1 Data bits—8 Flow control—none The default username is “admin” and password is “admin”. Refer to the SM24TAT2DPA CLI Reference for Command Line Interface (CLI) command information. 33702 Rev. A https://www.transition.com Page 13 of 23...
3. Initial Configuration via Web GUI After you power up the switch for the first time, you can configure the switch using a web browser. For more information about managing the switch, see the SM24TAT2DPA Web User Guide. To begin with the initial configuration stage, you must reconfigure your PC’s IP address and subnet mask so as to make sure the PC can communicate with the switch.
Page 15
The factory default Username of the switch is admin. The factory default Password of the switch is admin. For information on managing the switch via the Web UI, see the SM24TAT2DPA Web User Guide. For a detailed description of the management features, refer to the full Web User Guide 33702 Rev.
Transition Networks SM24TAT2DPA Install Guide 4. Troubleshooting Troubleshooting Chart The following table lists Issues, Causes, and Actions to resolve possible problems. Table 4 Troubleshooting Chart Issue Cause Action 1. Check if correct power cord is connected firmly to the switch and to the AC outlet socket.
Transition Networks SM24TAT2DPA Install Guide Software Specifications Layer 2 Switching Standard Spanning Tree 802.1d Rapid Spanning Tree (RSTP) 802.1w Spanning Tree Protocol (STP) Multiple Spanning Tree (MSTP) 802.1s Link Aggregation Control Protocol (LACP) IEEE 802.3ad Up to 13 groups Trunking...
Page 19
Transition Networks SM24TAT2DPA Install Guide Locks MAC addresses to ports, and limits the number of learned Port Security MAC address Prevents illegal IP address from accessing to specific port in the IP Source Guard switch RADIUS/ TACACS+ Supports RADIUS and TACACS+ authentication. Switch is a client...
Page 20
Transition Networks SM24TAT2DPA Install Guide networks. It gives complete visibility into the use of networks enabling performance optimization, accounting/billing for usage, and defense against security threats Used by network devices for advertising their identities, IEEE 802.1ab (LLDP) capabilities, and neighbors on an IEEE 802ab local area network...
If the repair is greater than $200.00, an estimate is issued to the customer for authorization of repair. If no authorization is obtained, or the product is deemed not repairable, Transition Networks will retain the $200.00 service 33702 Rev. A https://www.transition.com...
Transition Networks reserves the right to charge a $50 fee for all testing and shipping incurred, if after testing, a return is classified as “No Problem Found.”...
Need help?
Do you have a question about the SM24TAT2DPA and is the answer not in the manual?
Questions and answers