Piper Malibu PA-46-310P Pilot Operating Handbook page 523

r
KING .. ~
KY 196/196E/K~.19?/191:f: .
~i
•,v, .,.
VHF COMMUNICATiqf\k TRANSCEIV,J.,o,J,1~··
SECTION Ill
OPERATION
3.1
OPERATING PROCEDURE
3.1.1 TURN ON
To turn on the un;t, rotate the VOL knob clockwise from the OFF r,osition.
A non-volatile memory stores
frequency and mode information on power down. When power is activated the USE and STANDBY windows will
display the frequenc;es displayed at oower down and the mode of oDeration will be the same as at oower
down. Frequencies stored
in
memory channels are also retained.
After act;vating power, pull the VOL knob out to overr;de the automatic squelch and rotate the VOL knob
to the des;red audio level. Push ·the VOL. knob back in to activate the automatic squelch.
NOTE
THE
KY
196/197 SHOULD BE TURNED ON ONLY AFTER ENGINE STARTUP.
THIS IS A SIMPLE PRECAUTION WHICH HELPS PROTECT THE SOLID STATE
CIRCUITRY AND EXTENDS THE OPERATING LIFE OF YOUR AVIONICS
EQUIPMENT.
3.1.2 TRANSMIT INDICATOR
Dudng COMM transmission, a l;ghted
11
T
11
will appear between the USE and STANDBY windows to indicate tliat
the transceiver is ;n the transmit mode of operation.
3.1.3 MODES OF OPERATION
A. Frequency Mode
.J . .
•
• ·;::; . . . • .~ -~ • - . - ~-. ' • 'I_. • .. , •
~
-. . ..
~
..:. • •
In the Frequency Mo~e"-,~r_- ORe~tioo ·15,r~·r·e~~~te.i'D~--~~t~
~N&e¥1t~---
-- --o,
splay- arid can ihen~be transferred into the USE window by oressing the transfer button. The
Frequency Mode may be entered either by entering the Program Mode and entering rlashes
<---)
into Channel O or alternately may be entered from the Direct Tune Mode.
To select frequencies in this mode, the MHz oortion of the frequency displayed in tlie STANDRY
window may be incremented or decremented in 1
MHz
steos by rotatinq the
MHz
'<nob either
clockwise or counterclockwise. MHz frequencies will roll over or roll under at each banrl erlqe ·
(118 or 135 MHz). The KHz portion of the frequency disolayed in the STANDRY winrlow
may ~e
incremented or decremented by rotating the 25K/MEM knob either clockwise or counterclocl<wise.
Frequency selection is in 50 KHz steps when the.25K/MEM is pushed in and is in
'-5 KHz
steos
when the 25K/MEM is pulled out. · KHz frequencies roll over from
95
to
97
to
OfJ
and rol.l uncier·
from 00 to
95
or
97
according to the position of the 25K/MEM k.nob. Frequencies are
transferred from the STANDBY to the USE window and vice versa·
by
depressing tlie transfer
button.
e.
Program Mode
The Program Mode is used to program frequencies into memory for later recall and to select
ehher. the Frequency Mode or. t_he Channel Mode of operation.
To enter the Program Mode:
1. Depress and hold the transfer button until a flashing Channel number appears in the
USE
window of the d;splay (approximately three
(3)
seconds).
2. Pull the 25K/MEM knob out and rotate it until a
11
0
11
·appears in the USE window.
3.
Push the 25K/MEM knob in and rotate it until "uuu" is displayed in the STANDRY winnow of
the display.
Rev. 3, September, 1983
IM0035-5 . Paqe 3-1