Chapter 2: Xedge Chassis Systems; Overview - General DataComm Xedge 6000 Series Hardware Installation

Table of Contents

Advertisement

Chapter 2:

Overview

This chapter describes how to rackmount the specific Xedge chassis in use, ensure adequate air
flow, and make all necessary power and ground connections. This chapter also provides instructions
for local management access to the switch via a craft port on the Xedge chassis in use.
Typically, an Xedge switch is shipped from the factory with all modules installed in the chassis
ready for hard option setup and software configuration. In some cases, modules are pre-set and pre-
configured at the factory for your network application. Consult your Site/Network Documentation
Package or your field service representative for special instructions as required.
Table 2-1
describes each Xedge chassis, with specific procedures for each in the pages that follow.
Table 1-6
lists part numbers for all Xedge compatible cabinets, cables and connection panel kits.
Xedge 6002
(Two I/O slots)
Xedge 6160
(Four I/O slots)
Xedge 6280
(Seven I/O slots)
Table 2-1
Xedge Chassis Descriptions
Xedge 6645 Shelf
Dimensions:
Height
666 mm (26.2 in)
Width
482.61mm (19 in)
Depth
422 mm (16.6 in)
I/O Slots
Switch Fabric
1 or 2 XH Modules
Local Mgmnt Intfc
2 Chassis Rear Panel Ports 2 Chassis Rear Panel Ports
Power
DC
-48VDC
AC
Max Consumption
1300 W (with 2 PSUs)
Temperature
Relative Humidity
032R440-000
Issue 17
Xedge Chassis Systems
Xedge 6640 Shelf
666 mm (26.2 in.
482.61 mm (19 in)
422 mm (16.6 in)
16
16
1 or 2 XH Modules
--
--
100/120VAC, 50/60Hz
220/240VAC, 50/60Hz
1300 W (with 2 PSUs)
Operating: 0 to 50 deg. C (32 to 122 deg. F); Storage: -40 to 70 deg. C (-40 to 150 deg. F)
Up to 95% without condensation
Xedge 6000 Hardware
Installation & Setup Guide
Xedge 6640 or Xedge 6645
(16 I/O Slots)
Xedge 6280 Shelf
Xedge 6160 Shelf
222.5 mm (8.75 in)
112 mm (4.4 in)
482.61 mm (19 in)
482.61 mm (19 in)
488.95 mm (19.25 in)
476 mm (18.75 in)
7
4
1 XS or XH Module
1 XM, XS or XH Module
2 SMM Ports
2 SMM Ports
-48VDC
-48VDC
100/120VAC, 50/60Hz
100/120VAC, 50/60Hz
220/240VAC, 50/60Hz
220/240VAC, 50/60Hz
750 W (with 2 PSUs)
350 W (with 1 PSU)
Xedge 6002 Shelf
440.9 mm (1.74 in)
482.61 mm (19 in)
482.61 mm (19 in)
2
--
1 Chassis Front Panel Port
--
100/120VAC, 50/60Hz
220/240VAC, 50/60Hz
150 W
2-1

Advertisement

Table of Contents
loading

This manual is also suitable for:

Xedge 6280Xedge 6160Xedge 6645Xedge 6002Xedge 6640

Table of Contents