YOKOGAWA TA220 User Manual page 101

Command
:SAMPle:ARMing:SOURce
:SAMPle:BLOCk?
:SAMPle:BLOCk:SIZE
:SAMPle:BLOCk:STATe
:SAMPle:GATE?
:SAMPle:GATE:TIME
:SAMPle:INHibit?
:SAMPle:INHibit:POLarity
:SAMPle:INHibit:STATe
SSTart Group
:SSTart
STARt Group
:STARt
STATus Group
:STATus?
:STATus:CONDition?
:STATus:EESE
:STATus:EESR?
:STATus:ERRor?
:STATus:FILTer
:STATus:QMESsage
STOP Group
:STOP
STORe Group
:STORe
SYSTem Group
:SYSTem?
:SYSTem:BRIGhtness:DOTMatrix Sets the brightness of the dot matrix LED display or queries the current setting.
UNIT Group
:UNIT?
:UNIT:TIME
:UNIT:VOLTage
Common Command Group
*CAL?
*CLS
*ESE
*ESR?
*IDN?
*OPC
*OPC?
*OPT?
*RST
*SRE
*STB?
*TRG
*TST?
*WAI
IM 704610-01E
Function
Sets the arming source or queries the current setting.
Queries all settings related to block sampling.
Sets the number of blocks for block sampling or queries the current setting.
Turns block sampling ON and OFF or queries the current setting.
Queries all settings related to the gate.
Sets the gate time or queries the current setting.
Queries all settings related to inhibit.
Sets the polarity of inhibit or queries the current setting.
Turns ON/OFF inhibit or queries the current setting.
Executes single measurement.
Starts the measurement.
Queries all settings related to the communication status.
Queries contents of the status register.
Sets the extended event enable register value or queries the current setting.
Queries contents of the extended event register, and clears the register.
Queries any error codes that occur and message information.
Sets the transition filter or queries the current setting.
Sets whether or not to attach message information to the response to the
":STATus:ERRor?" query or queries the current setting.
Stops the measurement.
Stores setup information.
Queries all settings related to system.
Queries default units of voltage, time, and frequency.
Sets the default unit of time or queries the current setting.
Sets the default unit of voltage or queries the current setting.
Performs calibration and queries the result.
Clears the standard event register, extended event register, and the error queue. 10-32
Enters/queries the standard event enable register value.
Queries the standard event register, and clears the register.
Queries the instrument type.
Sets whether or not to clear the OPC event upon the completion of the
specified overlap command.
Creates a response upon the completion of the specified overlap command.
Queries the installed options.
Initializes settings.
Enters/queries the service request enable register value.
Queries the status byte register.
Executes single measurement.
Executes the self test and queries the result.
Holds the subsequent command until the completion of the specified overlap
operation.
10.2 Commands
Page
10-28
10-28
10-28
10-28
10-28
10-28
10-28
10-29
10-29
10-29
10-29
10-30
10-30
10-30
10-30
10-30
10-30
10-30
10-30
10-30
10-31
10-31
10-31
10
10-31
10-31
10-32
10-32
10-32
10-32
10-32
10-33
10-33
10-33
10-33
10-33
10-33
10-33
10-33
10-11