YOKOGAWA TA220 User Manual page 100

10.2 Commands
Command
INPut Group
:INPut?
:INPut:DATA?
:INPut:DATA:COUPling
:INPut:DATA:IMPedance
:INPut:DATA:POLarity
:INPut:DATA:TRIGger?
:INPut:DATA:TRIGger:LEVel
:INPut:DATA:TRIGger:MODE
:INPut:EQ?
:INPut:EQ:STATus
:INPut:EQ:BOOSt
:INPut:EQ:AGC
:INPut:EQ:DCCLamp
:INPut:EQ:PLLHold
:INPut:HISPeed:STATe
:INPut:PLL:STATus?
LVOut Group
:LVOut?
:LVOut:STATe
:LVOut:MODE
:LVOut:CYCLe
:LVOut:LEVel:RANGe
:LVOut:JUDGe:LEVel
:LVOut:JUDGe:RESult?
MEASure Group
:MEASure?
:MEASure:FUNCtion
:MEASure:SPEed?
MEMory Group
:MEMory?
:MEMory:BYTeorder
:MEMory:CLEar
:MEMory:DATaselect
:MEMory:END
:MEMory:FORMat
:MEMory:SEND?
:MEMory:STARt
RECall Group
:RECall
SAMPle Group
:SAMPle?
:SAMPle:ARMing?
:SAMPle:ARMing:DELay?
:SAMPle:ARMing:DELay:TIME
:SAMPle:ARMing:SLOPe
10-10
Function
Queries all settings related to signal input.
Queries all settings related to signal input (excluding the equalizer).
Sets the input coupling or queries the current setting.
Sets the input impedance or queries the current setting.
Sets the polarity of the data signal or queries the current setting.
Queries all settings related to the trigger.
Sets the trigger level (slice level) or queries the current setting.
Sets the trigger mode or queries the current setting.
Queries all settings related to the equalizer.
Sets the equalizer status or queries the current setting.
Sets the boost amount of the equalizer or queries the current setting.
Turns the equalizer's AGC function ON and OFF or queries the current setting.
Turns the equalizer's DC clamp function ON and OFF or queries the current
setting.
Turns the equalizer's PLL hold function ON and OFF or queries the current
setting.
Sets the D-to-C high speed calculation function or queries the current setting.
Queries PLL lock status.
Queries all settings related to level measurement.
Turns level measurement ON or OFF or queries the current setting.
Sets the level measurement output mode or queries the current setting.
Sets the level measurement output filter average coefficient or queries the
current setting.
Sets the upper and lower limit of the level measurement output range or
queries the current setting.
Sets the upper and lower limit of the level measurement output determination
level or queries the current setting.
Queries the level measurement output determination results.
Queries all settings related to measurement conditions.
Sets the measurement function or queries the current setting.
Queries the measurement speed.
Queries all settings related the external transmission of the measured data.
Sets the transmission order of binary data or queries the current setting.
Clears measured data.
Sets the data to be transmitted or queries the current setting.
Sets the position of the data to be transmitted or queries the current setting.
Sets format of the data to send or queries the current setting.
Executes the transmission of the measured data specified by
MEMory:DATaselect.
Sets the transmission start position of the data to be transmitted or queries
the current setting.
Recalling setting information
Queries all settings related to sampling.
Queries all settings related to arming.
Queries all settings related to the arming delay.
Sets the arming delay time or queries the current setting.
Sets the arming slope or queries the current setting.
Page
10-21
10-21
10-21
10-21
10-21
10-21
10-21
10-21
10-21
10-21
10-22
10-22
10-22
10-22
10-22
10-22
10-23
10-23
10-23
10-23
10-23
10-24
10-24
10-24
10-24
10-24
10-25
10-25
10-25
10-25
10-25
10-25
10-26
10-26
10-26
10-27
10-27
10-28
10-28
10-28
IM 704610-01E