ILX Lightwave LDX-3200 Series User Manual page 47

NAME PARAMETERS
LAS:ENAB:COND 1
LAS:ENAB:COND? NONE
LAS:ENAB:EVE 1
LAS:ENAB:EVE? NONE
LAS:ENAB:OUTOFF 1
LAS:ENAB:OUTOFF? NONE
LAS:EVENT? NONE
LAS:LDI 1
LAS:LDI? NONE
LAS:INC 0, 1 or 2
LAS:LDV 1
LAS:LDV? NONE
LAS:LIM:I1 1
LAS:LIM:I1? NONE
LAS:LIM:I2 1
LAS:LIM:I2? NONE
LAS:LIM:I5 1
LAS:LIM:I5? NONE
LAS:LIM:MDP 1
LAS:LIM:MDP? NONE
LAS:LIM:V 1
LAS:LIM:V? NONE
LAS:MDI 1
LAS:MDI? NONE
LAS:MDLN 1
LAS:MDLN? NONE
LAS:MDP 1
LAS:MDP? NONE
LAS:MODE? NONE
LAS:MODE:IHBW NONE
LAS:MODE:ILBW NONE
LAS:MODE:MDP NONE
LAS:OUT 1
LAS:OUT? NONE
LAS:RAN 1
LAS:RAN? NONE
LAS:SET:LDI? NONE
LAS:SET:MDI? NONE
Table 4.1 LDX-3200 Series Device-Dependent Commands (Cont.)
COMMAND REFERENCE
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
LDX-3200 SERIES DEVICE-DEPENDENT COMMANDS
FUNCTION
Sets the enable register for LASER conditions.
Returns the value of the LAS conditions enable register.
Sets the enable register for LAS events.
Returns the value of the LAS event enable register.
Sets the enable register for LAS conditions which turn the LAS output off.
Returns the value of the LAS outoff enable register.
Returns the value of the LAS event register.
Used to set the LASER constant current source set point value.
Used to return the constant current source measured value
Used to increment the LASER set point value by one or more steps.
Used to set the laser voltage value for calibration.
Used to return the measured laser voltage value
Used to set the LASER current source limit (high range for LDX-3210).
Used to return the LASER current source limit (high range for LDX-
3210).
Used to set the LASER current source limit (low range for LDX-3220).
Used to return the LASER current source limit (low range for LDX-
3220).
Used to set the LASER current source limit (high range for LDX-3220,
low range for LDX-3210).
Used to return the LASER current source limit (high range for LDX-
3220, low range for LDX-3210).
Used to set the constant optical power (from monitor PD) limit value.
Used to return the optical power (from monitor PD) limit value.
Used to set the LASER compliance voltage limit value.
Used to return the LASER compliance voltage limit value.
Used to set the constant optical power set point, if PD responsivity is 0.
Used to return the monitor PD current measured value.
Used to enable/disable the front panel modulation input.
Used to return the status of the front panel modulation input.
Used to set the constant optical power set point.
Returns the actual monitor PD power value.
Returns the mode, I (current), IHBW (high bandwidth) or P (optical
power).
Sets the mode to constant current, high bandwidth.
Sets the mode to constant current (low bandwidth) mode.
Sets the mode to constant optical power mode.
Used to enable/disable the current source output.
Returns the current source output status.
Sets the laser current output range.
Returns the laser current output range.
Returns the laser constant I (current) set point.
Returns the laser constant optical power set point.
PAGE 2
CHPT 4