KidKraft Cedar Summit Canyon Ridge Installation And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. KidKraft Manuals
  4. Play Sets & Playground Equipment
  5. Cedar Summit Canyon Ridge
  6. Installation and operating instructions manual

KidKraft Cedar Summit Canyon Ridge Installation And Operating Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

C A N Y O N R I D G E – F 2 5 7 1 5
INSTALLATION AND OPERATING INSTRUCTIONS
30'-9"
18'-9"
CANYON RIDGE h: 11FT
10 - 12 Hrs
10 - 12 Hrs
2-4 Hrs
2 - 4 Hrs
FOR FORT & SWING
FOR FORT & SWING
TUBE SLIDE
TWO PERSON
ASSEMBLY
WARNING
Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE -30' 9" x 27'1" (9.37 x 8.23 m) area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6' 7" (2.01 m)
27' -1"
11'-10"
CAPACITY - 12 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as multi-unit residences, schools, churches,
nurseries, day cares or parks.
Cedar Summit by KidKraft
4630 Olin Road
Dallas, TX 75244, United States
customersupport@kidkraft
Online Parts Replacement:
Cedarsummitplay . c om/parts-center-warranty-claim
Customer Service:
1(800) 933-0771 or (972) 385-0100
KidKraft Netherlands BV
Olympisch Stadion 29
1076DE Amsterdam, The Netherlands
Europe Customer Service: +31 (0)20 305 8620
europecustomerservice@kidkraft . c om
EU Online Parts Replacement: parts . k idkraft . e u
To reduce the risk of serious injury or death, you must read and
follow these instructions. Keep and refer to these instructions
often and give them to any future owner of this play set.

Table of Contents

Warnings And Safe Play Instructions . . . . . . . . . . pg . 2
Protective Surfacing Guidelines . . . . . . . . . . . . . . . pg . 3
Instructions For Proper Maintenance . . . . . . . . . pg . 4
About Our Wood – Limited Warranty . . . . . . . . . pg . 5
Keys To Assembly Success . . . . . . . . . . . . . . . . . . . . pg . 6
Part ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg . 8
Step-By-Step Instructions . . . . . . . . . . . . . . . . . . .pg . 19
Installation of I . D . / Warning Plaque . . . . . .Final Step
9405715
10 - 12 Hrs
FOR FORT & SWING
TWO PERSON
ASSEMBLY
Rev 12/14/2017

Advertisement

Table of Contents
loading

Related Manuals for KidKraft Cedar Summit Canyon Ridge

Summary of Contents for KidKraft Cedar Summit Canyon Ridge

  • Page 1 ASSEMBLY ASSEMBLY Table of Contents Cedar Summit by KidKraft 4630 Olin Road Warnings and Safe Play Instructions . . . . . . . . . . pg . 2 Dallas, TX 75244, United States Protective Surfacing Guidelines .
  • Page 2 Warnings and Safe Play Instructions CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using this play system.
  • Page 3 Protective Surfacing - Reducing Risk of Serious Head Injury From Falls One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM F1292.
  • Page 4 Instructions for Proper Maintenance Your Cedar Summit Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important that you, the owner, properly maintain it.
  • Page 5 Such use may lead to product failure and potential injury. Any and all public use will void this warranty. Cedar Summit by KidKraft disclaims all other representations and warranties of any kind, express or implied province to province. This warranty excludes all consequential damages, however, some states do not allow the...
  • Page 6 Keys to Assembly Success Tools Required • Tape Measure • #1, #3 Phillips or Robertson • Open End Wrench • 3/16” Hex Key • Carpenters Level bit or Screwdriver (1/2”, 7/16” & 9/16”) • 8’ Step Ladder • Carpenters Square •...
  • Page 7 Your Key To Quick Assembly SORTING WOOD PARTS INTO EACH ASSEMBLY STEP WILL SAVE TIME! Step Step Step SAVE TIME - TIP #1: Open each box with wood parts and look for the Key Number stamped on the end of the wood part (see chart below). Sort each wood part into the different assembly steps.
  • Page 10 Part Identification (Reduced Size) (1) 135 - Bell Top RT 5/8 x 3-3/8 x 11-1/4" FSC - Box 2 4609101 (1) 134 - Bell Top 5/8 x 3-3/8 x 11-1/4" FSC - Box 2 - 4609102 (1) 023 - 1 x 4 x 21" - Ladder Gap FSC - Box 2 - 4598958 (4) 230 - 1 x 4 x 29"...
  • Page 11 Part Identification (Reduced Size) (2) 201 - 1 x 2 x 34-1/8" - Upright Crowsnest FSC - Box 3 - 4599072 (2) 212 - 3/4 x 3-1/4 x 14-3/4" - Crowsnest Side FSC - Box 2 - 4599042 (2) 210 - 3/4 x 5-1/4 x 14-3/4" - Crowsnest Bottom Side FSC - Box 3- 4599037 (2) 404 - 15/16 x 3 x 19-1/4"...
  • Page 12 Part Identification (Reduced Size) (1) 092 - 5/4 x 4 x 24½" - Support Diagonal FSC - Box 2 - 4599111 (1) 192 - 5/4 x 4 x 34" - Crowsnest Back FSC - Box 2 - 4599036 (2) 411 - Swing Side Upright 1-1/4 x 2-1/2 x 16-1/2" FSC - Box 3 - 4599112 (2) 400 - TB Support 1¼...
  • Page 13 Part Identification (Reduced Size) (2) 450 - Mid Roof End 1¼ x 4 x 6" FSC - Box 3 - 4599119 (2) 402 - Left Upright 1¼ x 4¼ x 16½" FSC - Box 3 - 4599107 (2) 136 - Bell Support 1½ x 1½ x 10-5/8" FSC - Box 2 - 4609100 (1) 130 - 2 x 2 x 39-5/8"...
  • Page 14 Part Identification (Reduced Size) 1x - Dormer Roof Set FSC 370 Right - 371 Left Dormer (4598068) - Box 3 (1) 391 (1) 392 Front Small Roof 1¼ x 29 3/16 x 21-7/8" Back Small Roof 1-1/4 x 28-15/16 x 21-7/8" FSC - Box 3 - 47599098 FSC - Box 3 - 47599091 (1) 350...
  • Page 15 Part Identification (Reduced Size) (1) 040 - 1-1/4 x 37 x 92" (1) 051 - 1-1/4 x 43 x 92" (1) 050 - 1-1/4 x 37 x 92" Slide End Panel FSC Front Wall Panel FSC SW Wall Panel FSC Box 2 - 47599078 Box 3 - 47598981 Box 3 - 47599007...
  • Page 16 Hardware Identification (Actual Size) Wafe Bolt 5/16 x 2-1/8" Wafer Bolt 5/16 x 3" (6) WB9 - - (53613324) (7) WB7 - - (53613330) Wafer Bolt 5/16 x 2-3/8" (1) WB8 - - (53613326) 1/4 x 1-3/8" (4) WL3 - Wafer Lag - (52613216) Wafer Bolt 5/16 x 2-5/8"...
  • Page 17 Hardware Identification (Actual Size) (13) TN1 - 1/4" T - Nut (54503200) (1) LW2 - 5/16" Lock Washer - (51303300) (9) FW0 - 3/16" Flat Washer - (51103100) (22) LW1 - 1/4" Lock Washer - (51303200) (18) FW1 - 1/4" Flat Washer - (51103200) (21) TN2 - 5/16"...
  • Page 18 Part Identification (Reduced Part Size) 1x - Cedar Summit Plaque 1x - TNR3 Tube Support (9320358) (9200258) 1x - Telescope w/ Mount 1x - TNR3 Post Mount (3320161) (9200257) 1x - Plastic Formed Washer (18 Pk) (3290000) 1x - KK ID Plaque (9320357) (9320370) 1x - Rocks (9pk) (3320093)
  • Page 19 Europe Customer Service: +31 (0)20 305 8620 Online Parts Replacement: europecustomerservice@kidkraft.com Cedarsummitplay.com/parts-center- EU Online Parts Replacement: parts.kidkraft.eu warranty-claim Customer Service: 1(800) 933-0771 or (972) 385-0100 Read the assembly manual completely, paying special attention to ANSI warnings; notes; and safety/maintenance information.
  • Page 20 Step 2: Access Ladder / Rockwall Assembly Part 1 A: Place (020) Left Access on one side of 4 (022) Treads and (021) Right Access on the other side with the grooves facing in. (fig. 2.1) B: Fit each (022) Tread into grooves on both (020) and (021) Access rails, make sure the top edge of the (022) Treads are flush to the front of the Access rails.
  • Page 21 Step 2: Access Ladder / Rockwall Assembly Part 2 D: Place (023) Ladder Gap on each access rail so there is a 2-3/8” gap between (023) Ladder Gap and the top (022) Tread. Attach using 4 (S20) #8 x 1-3/8” Wood Screws. (fig. 2.3) E: Place (024) Rock Rail on the ground next to (020) Left Access so it matches the orientation of the two access rails as shown in fig.
  • Page 22 Step 3: Rockwall Assembly Part 1 A: Place (031) Access Board flush to the top of the Access Ladder/Rockwall Assembly and (030) Access Rock Bottom at the bottom of the assembly as shown in fig. 3.1. Then place (032) Board Rock A and (033) Board Rock B as shown in fig.
  • Page 23 Step 3: Rockwall Assembly Part 2 C: Alternating colours and shapes, attach 1 rock to each rock board using 1 (PB2) 1/4 x 1-1/4” Pan Bolt (with lock washer, flat washer and barrel nut) and 1 (S10) #8 x 1” Pan Screw per rock. (fig. 3.2 and 3.3) The Pan Screw is placed in the hole beneath the Pan Bolt.
  • Page 24 Step 4: Slide Wall Assembly A: Place (041) Narrow Back Panel against the left side of (040) Slide End Panel noticing panel orientation. The tops and bottoms of the panels should be flush and panels square. Pre-drill with a 3/16” drill bit, then fasten (041) Narrow Back Panel to (040) Slide End Panel with 4 (WL5) 1/4 x 2-1/2”...
  • Page 25 Step 5: Swing Wall Assembly A: Place (051) Front Wall Panel against the left side of (050) SW Wall Panel noticing panel orientation. The tops and bottoms of the panels should be flush and panels square. Pre-drill with a 3/16” drill bit, then fasten (051) Front Wall Panel to (050) SW Wall Panel with 4 (WL5) 1/4 x 2-1/2”...
  • Page 26 Step 6: Join Swing and Slide Wall Assemblies Part 1 A: With at least two helpers lift the Slide Wall Assembly and Swing Wall Assembly so the (041) Narrow Back Panel and (042) Narrow Front Panel meet with (052) Back Wall Panel and (051) Front Wall Panel and are tight together as shown in fig.
  • Page 27 Step 6: Join Swing and Slide Wall Assemblies Part 2 C: From inside the assembly, tight to both (040) Slide End Wall and (050) SW Wall Panel, halfway up the assembly, 5/8” below the panel, loosely attach 1 (061) Side Joist to (041) Narrow Back Panel and (052) Back Wall Panel with 3 (WB10) 5/16 x 2-5/8”...
  • Page 28 Step 6: Join Swing and Slide Wall Assemblies Part 3 E: From inside the assembly, place 1 (062) Tie centred between (041) Narrow Back Panel and (052) Back Wall Panel so it is flush to the tops of the panels and the angled ends face out then attach with 2 (H10) 1/4 x 2-1/4” Hex Bolts (with lock washer, flat washer and t-nut) and 2 (S11) #8 x 2”...
  • Page 29 Step 6: Join Swing and Slide Wall Assemblies Part 4 G: On the inside of the assembly attach (041) Narrow Back Panel to (052) Back Wall Panel using 2 Flat Panel Brackets in the places shown with 4 (S8) #12 x 3/4” Pan Screws per bracket. (fig. 6.8 and 6.9) H: Repeat Step G to attach (042) Narrow Front Panel to (051) Front Wall Panel.
  • Page 30 Step 7: Floor Assembly Part 1 A: Place 1 (070) Floor Board tight to (040) Slide End Panel and 1 tight to (050) SW Wall Panel then attach each to the (061) Side Joists with 4 (S20) #8 x 1-3/8” Wood Screws per board. (fig.
  • Page 31 Step 7: Floor Assembly Part 2 C: Measure the distance from the Back Wall to the Front Wall from the inside of the panels to make sure it equals 35-3/4”. Maintain this measurement when installing the floor boards. Starting at the Slide Wall place 3 (070) Floor Boards tight to the previously attached (070) Floor Board, followed by 1 (072) Floor Board then 8 more (070) Floor Boards.
  • Page 32 Step 8: Attach Wall Tops A: In the opening of (050) SW Wall Panel, from the inside, attach (080) SW Wall Top, tight to the corner of the panels with overhang facing in with 1 (S11) #8 x 2” Wood Screw at each end as shown in fig. 8.1 and 8.2. B: Attach (080) SW Wall Top to slat in (050) SW Wall Panel with 1 Corner Bracket using 3 (S37) #7 x 5/8”...
  • Page 33 Step 9: Attach Diagonals Part 1 A: Loosely attach (090) SW Ground to (091) Diagonal with 1 (WB9) 5/16 x 2-1/8” Wafer Bolt (with flat washer and t-nut) then place (091) Diagonal tight and flush to the front of (040) Slide End Panel. (090) SW Ground to be flush to the bottom of (040) Slide End Panel.
  • Page 34 Step 9: Attach Diagonals Part 2 D: Loosely attach (092) Support Diagonal to (093) Diagonal with 1 (WB9) 5/16 x 2-1/8” Wafer Bolt (with flat washer and t-nut) then place (093) Diagonal tight and flush to the front of (050) SW Wall Panel. (092) Support Diagonal to be flush to the bottom of (050) SW Wall Panel.
  • Page 35 Step 10: Attach Access Ladder/Rockwall Assembly Part 1 A: Place Access Ladder/Rockwall Assembly from Step 3 against (052) Back Wall Panel, flush to the outside edge and flush to the top of the floor boards then attach with 4 (S11) #8 x 2” Wood Screws. (fig. 10.1 and 10.2) Fig.
  • Page 36 Step 10: Attach Access Ladder/Rockwall Assembly Part 2 B: Place (031) Access Board from Step 3, Part 1 against (020) Left Access and (024) Rock Rail and flush to the top then attach with 4 (S20) #8 x 1-3/8” Wood Screws. (fig. 10.3 and 10.4) Fig.
  • Page 37 Step 10: Attach Access Ladder/Rockwall Assembly Part 3 C: Place (100) RW-AL Ground Brace flush to the end and bottom of (024) Rock Rail. Make sure the other end of the board is flush to the bottom of (050) SW Wall Panel then attach to (024) Rock Rail with 2 (S11) #8 x 2” Wood Screws.
  • Page 38 Step 11: Attach Steel Hand Grips to Fort A: Measure 6” from the top of (025) RW/AL Support on (052) Back Wall Panel in the 2 places shown below, pre-drill with a 1/8” drill bit then attach 2 Steel Hand Grips with 2 (WL3) 1/4 x 1-3/8” Wafer Lag (with flat washer) per Steel Hand Grip.
  • Page 39 Step 12: Door Panel Assembly Part 1 A: On the inside of (120) Door Window Panel measure 15” up from the bottom and attach Catch Plate flush to the edge using 2 (S38) #7 x 1-1/8” Pan Screws. (fig. 12.1 and 12.2) B: On the inside of (120) Door Window Panel measure 22”...
  • Page 40 Step 12: Door Panel Assembly Part 2 C: On the outside of the (120) Door Window Panel attach the second Door Handle at approximately the same place as the one on the inside. Use 2 (S37) #7 x 5/8” Pan Screws. (fig. 12.3) D: Attach 2 Door Hinges on the outside of the (120) Door Window Panel on the opposite side from the Door Handle.
  • Page 41 Step 12: Door Panel Assembly Part 3 E: In the opening for the door, measure 3/4” from the top of (042) Narrow Front Panel bottom and maximum 5/8” from right side of the opening which would be the Door Hinge side and attach the remaining side of the hinges to (042) Narrow Front Panel using 3 (S37) #7 x 5/8”...
  • Page 42 Step 12: Door Panel Assembly Part 4 F: In the notched out opening of (121) Door Stop attach the Magnetic Catch using 2 (S38) #7 x 1-1/8” Pan Screws. (fig. 12.7) Important: Use a hand held screw driver and DO NOT over tighten. G: On the inside of the assembly, attach (121) Door Stop to (042) Narrow Front Panel with 3 (S11) #8 x 2”...
  • Page 43 Step 13: Front Wall Assembly Part 1 A: Place (130) Table Support flush to the notched out ends of (131) Table Top and attach with 4 (S7) #12 x 2” Pan Screws as shown in fig. 13.1. B: Place Table Top Assembly tight in the opening of (051) Front Wall Panel and attach (130) Table Support to (051) Front Wall Panel with 2 (S3) #8 x 2-1/2”...
  • Page 44 Step 13: Front Wall Assembly Part 2 C: From the inside of the assembly attach (131) Table Top to slats in (051) Front Wall Panel with 2 Flat Brackets using 3 (S0) #8 x 7/8” Truss Screws per bracket. (fig. 13.4 and 13.5) Fig.
  • Page 45 Step 13: Front Wall Assembly Part 3 D: Place (134) Bell Top on top of (136) Bell Support so the angled and back edges are flush then attach with 3 (S20) #8 x 1-3/8” Wood Screws. Repeat by attaching (135) Bell Top RT to top of (136) Bell Support. Rounded ends of (134) Bell Top and (135) Bell Top RT are at the bottom.
  • Page 46 Step 14: Swing Beam Assembly Part 1 A: Attach 6 Heavy Duty Swing Hangers to (140) Engineered SW Beam using 2 (G13) 5/16 x 6-1/8” Hex Bolt (with 2 flat washers, plastic formed washer and lock nut) per swing hanger, as shown in fig. 14.1 and 14.2. B: Attach 1 Spring Loaded Quick Link to each Heavy Duty Swing Hanger.
  • Page 47 Step 14: Swing Beam Assembly Part 2 E: On the Fort End of (140) Engineered SW Beam attach 2 Heavy Flat Brackets with 2 (G21) 5/16 x 3-3/4” Hex Bolts (with 2 flat washers and 1 lock nut). (fig. 14.6 and 14.7) F: Place (141) SW Mount in between both Heavy Flat Brackets and place 1 Heavy L-Bracket against (140) Engineered SW Beam and (141) SW Mount.
  • Page 48 Step 15: Swing Post Assembly Part 1 Heavy L-Bracket Note: Keep all bolts from Step 15 series loose Fig. 15.1 until start of Step 17 Bottom View A: Place (150) SW Block Angle on top of (151) Block SW and attach 2 Heavy L-Brackets on top of (150) SW Block Angle feeding 2 (G17) 3/8 x 6”...
  • Page 49 Step 15: Swing Post Assembly Part 2 D: Place Swing End of (140) Engineered SW Beam in between Heavy L-Brackets assembled in Step A making sure holes are lined up then attach Swing Post Assembly to Swing Beam Assembly using 1 (G20) 3/8 x 4” Hex Bolt (with 2 flat washers and lock nut) through Heavy L-Bracket.
  • Page 50 Step 15: Swing Post Assembly Part 3 F: Place (141) SW Mount flush to the top of (050) SW Wall Panel. Attach with 1 (G5) 5/16 x 4-1/2” Hex Bolt (with lock washer, flat washer and t-nut) in the bottom hole from outside the assembly and 1 (G5) 5/16 x 4-1/2” Hex Bolt (with 2 x flat washer and 1 lock nut) in the top hole from inside the assembly.
  • Page 51 Step 16: Attach Cross Support Pre-drill all holes using a 3/16” drill bit before installing the lag screws. Fig. 16.1 A: To adjust for uneven ground, raise or lower the (160) Support Cross on the (152) SW Post. Make sure the Support Cross is level prior to attaching with the lag screws.
  • Page 52 Step 17: Final Swing Post Assembly Pre-drill all holes using a 3/16” drill bit before installing the lag screws. Note: Tighten all bolts from Step 15 series before installing lag screws. A: Attach 1 (LS9) 5/16 x 4-3/4” Lag Screw (with flat washer) into each (152) SW Post, as shown in fig. 17.1. B: Attach 1 (LS9) 5/16 x 4-3/4”...
  • Page 53 Step 18: Install Ground Stakes MOVE FORT TO FINAL LOCATION PRIOR TO STAKING FINAL LOCATION MUST BE LEVEL GROUND A: In the 5 places shown in fig. 18.1 drive the Rebar Ground Stakes 13” into the ground against (091) Diagonal, (093) Diagonal, (024) Rock Rail and both (152) SW Posts.
  • Page 54 Step 19: Lower Crowsnest Assembly Part 1 A: Attach 1 (190) Crowsnest Gusset to 1 (191) Crowsnest Joist so the bottoms and ends are flush with 1 (S7) #12 x 2” Pan Screw. Repeat to make a second set with the (191) Crowsnest Joist on the opposite side from the first.
  • Page 55 Step 19: Lower Crowsnest Assembly Part 2 B: Place (192) Crowsnest Back against the ends of (191) Crowsnest Joists so the tops are flush then attach with 4 (S3) #8 x 2-1/2” Wood Screws. (fig. 19.3 and 19.4) Fig. 19.3 Flush Flush Fig.
  • Page 56 Step 20: Upper Crowsnest Assembly Part 1 A: Loosely attach (200) Crowsnest Top to 2 (201) Upright Crowsnest using 2 (WB9) 5/16 x 2-1/8” Wafer Bolts (with flat washer and t-nut). The distance between uprights must be 25-1/2”. (fig. 20.1) B: Loosely attach (202) Crowsnest Front to each (201) Upright Crowsnest using 2 (WB9) 5/16 x 2-1/8”...
  • Page 57 Step 20: Upper Crowsnest Assembly Part 2 D: Attach 1 (203) Crowsnest Short flush to the top of (200) Crowsnest Top using 6 (S11) #8 x 2” Wood Screws as shown in fig. 20.2. E: Attach 1 (204) Crowsnest Spacer flush to the outside of each (201) Upright Crowsnest using 3 (S11) #8 x 2” Wood Screws per board as shown in fig.
  • Page 58 Step 21: Crowsnest Assembly Part 1 A: Attach 1 (210) Crowsnest Bottom Side flush to the inside edge of the panel posts on (040) Slide End Panel and tight to the top of the floor support on (040) Slide End Panel using 3 (S11) #8 x 2” Wood Screws per side.
  • Page 59 Step 21: Crowsnest Assembly Part 2 B: Place the Lower Crowsnest Assembly from Step 19 centred in the opening of (040) Slide End Panel, in between (210) Crowsnest Bottom Sides, tight to the top of the floor boards then attach with 2 (S11) #8 x 2” Wood Screws per side.
  • Page 60 Step 21: Crowsnest Assembly Part 3 C: Attach 1 (211) Short Crowsnest Joist tight to (192) Crowsnest Back and flush to the bottom of each (210) Crowsnest Bottom Side using 3 (S20) #8 x 1-3/8” Wood Screws per board as shown in fig. 21.5. Screws to be installed from outside the assembly.
  • Page 61 Step 21: Crowsnest Assembly Part 4 E: Place Upper Crowsnest Assembly from Step 20 in between (210) Crowsnest Bottom Sides so (202) Crowsnest Front is flush to the bottom and front of each (210) Crowsnest Bottom Side and to the tops of (190) Crowsnest Gussets and (191) Crowsnest Joists.
  • Page 62 Step 21: Crowsnest Assembly Part 5 F: Attach (202) Crowsnest Front flush to the top of each (190) Crowsnest Gusset and each (191) Crowsnest Joist with 8 (S4) #8 x 3” Wood Screws. (fig. 21.8) G: Place 1 (212) Crowsnest Side flush to the top and front of (200) Crowsnest Top make sure each board is level then attach with 2 (S3) #8 x 2-1/2”...
  • Page 63 Step 21: Crowsnest Assembly Part 6 H: From inside the assembly attach (040) Slide End Panel to each (190) Crowsnest Gusset with 2 (S4) #8 x 3” Wood Screws per gusset. (fig. 21.9 and 21.10) I: Double check that each (212) Crowsnest Side is level then attach to (040) Slide End Panel flush to the inside of the panel post with 2 (S3) #8 x 2-1/2”...
  • Page 64 Step 22: Crowsnest Floor Assembly A: Lay down (220) Crowsnest Gap Board flush to front of (202) Crowsnest Front and (221) Crowsnest Floor flush to back of (192) Crowsnest Back. In between the gap and floor boards place another (221) Crowsnest Floor.
  • Page 65 Step 23: Crowsnest Wall Assembly A: Tight to each (201) Upright Crowsnest and tight to the floor and gap boards attach 1 (230) Cedar Wall to each (210) Crowsnest Bottom Side and (212) Crowsnest Side with 4 (S1) #8 x 1-1/8” Wood Screws per board. (fig. 23.1) B: Measure 2-1/4”...
  • Page 66 For a Helpful Hints video on Step 24: Slide Section Assemblies assembling this tube slide Part 1 please visit http://bit.ly/2ACggzj Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess. (fig. 24.3) A: Fit 2 TNR2 Slide Elbows together and attach with 8 (PB1) 1/4 x 3/4”...
  • Page 67 Step 24: Slide Section Assemblies Part 2 Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess. (fig. 24.3) D: Attach TNR2 Slide Exit Top and the remaining TNR2 Slide Elbow together using 8 (PB1) 1/4 x 3/4”...
  • Page 68 Step 25: Attach Flange Assembly to Fort A: With a helper place the Flange Assembly flush to the Crowsnest on the fort as shown in fig. 25.1 and 25.5, then pre-drill 1/8” pilot holes in the bottom 4 mounting locations on (220) Crowsnest Gap Board (approximate spots where circles are on figure), making sure the pre-drilled holes are a minimum of 1”...
  • Page 69 Step 26: Attach Elbow Assembly to Flange Assembly Part 1 Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess. Keep all bolts loose until further step.
  • Page 70 Step 26: Attach Elbow Assembly to Flange Assembly Part 2 Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go Fig. 26.5 through the side with the hexagonal recess. Keep all bolts loose until further step.
  • Page 71 Step 27: Attach Elbow Assembly to Elbow Assembly Part 1 Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through Fig. 27.1 the side with the hexagonal recess. Keep all bolts loose until further step.
  • Page 72 DO NOT USE DO NOT USE USE IMAGE Step 27: Attach Elbow Assembly to Elbow Assembly USE IMAGE Part 2 Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess. Keep all bolts loose until further step.
  • Page 73 Step 28: TNR Brace Assembly A: Attach (281) TNR Upright to (280) TNR Ground Brace with 1 (H8) 1/4 x 4-1/4” Hex Bolt (with lock washer, flat washer and t-nut) in the top hole. Make sure both boards are square then attach with 1 (S11) #8 x 2”...
  • Page 74 Step 29: Attach Elbow Assemblies and TNR2 Slide Support Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess. Keep all bolts loose until further step.
  • Page 75 Step 30: Attach TNR Brace Assembly A: Use (281) TNR Upright as a guide to judge the proper bolt location, remove the bottom pan bolt and nut. The bolt will no longer be needed, but keep the lock nut. (fig. 30.1 and 30.2) B: Attach the top of the TNR3 Post Mount to TNR2 Slide Clamp Ring using 1 (PB2) 1/4 x 1-1/4”...
  • Page 76 Step 31: Attach TNR3 Slide Exit to Exit Elbow Assembly A: Insert flange of Exit Elbow Assembly (slide elbow) into the slots on TNR3 Short Exit. (fig. 31.1) B: Rotate Slide Exit and use Quadrex Driver as a guide pin so the holes are aligned and attach with 5 (PB1) 1/4 x 3/4”...
  • Page 77 Step 32: Attach Exit End Assembly to Fort Note: When installing Pan Bolts make sure to Fig. 32.1 Top Slide Bolt Holes Elbow look at holes so bolts go through the side with the Assembly round recess and the lock nuts go through the side with the hexagonal recess.
  • Page 78 Step 33: Attach Ground Stake to TNR Upright A: In the spot shown in fig. 33.1 drive 1 Rebar Ground Stake 13” into the ground against the (280) TNR Ground Brace. Be careful not to hit the washer while hammering stake into the ground as this could cause the washer to break off.
  • Page 79 Step 34: Roof Support Assemblies A: Attach 1 (340) Roof Support to a second (340) Roof Support at peak using 1 (S4) #8 x 3” Wood Screw. Repeat this twice so there are 2 Roof Support Assemblies. (fig. 34.1) B: Attach 1 (341) Roof Support Small to a second (341) Roof Support Small at peak using 1 (S4) #8 x 3” Wood Screw.
  • Page 80 Step 35: Large Roof Assembly Part 1 A: Place (350) Front Roof Panel against (351) Back Roof Panel so the tops form a peak then tight to the inside edge of the outside slats attach 1 Narrow Angle Bracket per slat with 2 (S0) #8 x 7/8” Truss Screws per bracket. (fig.
  • Page 81 Step 35: Large Roof Assembly Part 2 C: Place 1 Roof Support Assembly against one side so the peaks meet and the ends of the roof supports are flush with the ends of the roof panels. Attach with 8 (S11) #8 x 2” Wood Screws. (fig. 35.4) D: Attach the second Roof Support Assembly on the opposite side, peaks to meet and ends are flush with 8 (S11) #8 x 2”...
  • Page 82 Step 36: Attach MOD 3 Pane Gable A: On each side of the Large Roof Assembly attach 2 MOD 3 Pane Gables to the inside of the (340) Roof Supports with 4 (S0) #8 x 7/8” Truss Screws per gable. (fig. 36.1 and 36.2) MOD 3 Pane Gable Fig.
  • Page 83 Step 37: Gable Dormer Assembly A: Place (370) Gable Dormer RT tight to (371) Gable Dormer LT then place MOD 3 Pane Gable tight against the dormers and attach with 4 (S0) #8 x 7/8” Truss Screws. (fig. 37.1) B: Attach (370) Gable Dormer RT and (371) Gable Dormer LT with 1 Narrow Angle Bracket using 2 (S0) #8 x 7/8”...
  • Page 84 Step 38: Attach Gable Dormer to Large Roof A: On the outside of the Large Roof Assembly on (350) Front Roof Panel, on the 4th siding down, place (380) Dormer Cleat centred on the panel (over the middle inside slat) then attach with 2 (S11) #8 x 2” Wood Screws. Make sure the screws go into the siding and the slats.
  • Page 85 Step 39: Small Roof Assembly Part 1 A: Attach 1 (390) Mid Roof Support to a second (390) Mid Roof Support at peak using 1 (S4) #8 x 3” Wood Screw. Notice pilot holes are at the bottom of the boards. (fig. 39.1) Fig.
  • Page 86 Step 39: Small Roof Assembly Part 2 B: Place (391) Front Small Roof against (392) Back Small Roof so the tops form a peak then tight to the inside edge of the outside slats attach 1 Narrow Angle Bracket per slat with 2 (S0) #8 x 7/8” Truss Screws per bracket. (fig.
  • Page 87 Step 39: Small Roof Assembly Part 3 D: Place Small Roof Support Assembly against opposite side of the Small Roof Assembly so the peaks meet and the ends of the roof supports are flush with the ends of the roof panels. Attach with 6 (S11) #8 x 2” Wood Screws.
  • Page 88 Step 40: Transom Assembly Part 1 A: With the notches facing down tap 3 1/4” T-nuts into (400) TB Support then fit (401) Right Upright, (402) Left Upright and (403) Centre Upright into the grooves so the ends and tops are flush. Attach with 3 (H9) 1/4 x 1-1/4” Hex Bolts (with lock washer and flat washer).
  • Page 89 Step 40: Transom Assembly Part 2 B: Place 2 MOD 5 Pane Windows in the openings and attach to (401) Right Upright, (402) Left Upright and (403) Centre Upright with 4 (S0) #8 x 7/8” Truss Screws per window. (fig. 40.2) C: Attach (404) Wall Tie flush to the top of (400) TB Support and to (403) Centre Upright with 4 (S11) #8 x 2”...
  • Page 90 Step 41: Swing Top Assembly A: Attach (410) Swing Top to 2 (411) Swing Side Uprights with 2 (H3) 1/4 x 2-1/2” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 41.1) Fig. 41.1 1/4” Lock Washer 1/4” Flat Washer 1/4”...
  • Page 91 Step 42: Attach Wall Supports A: Tight to the floor boards and tight in each corner of the (050) SW Wall Panel attach 2 (420) Wall Supports to (050) SW Wall Panel with 3 (S3) #8 x 2-1/2” Wood Screws per support. (fig. 42.1) Fig.
  • Page 92 Step 43: Attach Swing Top Assembly A: Tight to the top of (050) SW Wall Panel and flush to the outside of each (420) Wall Support place Swing Top Assembly then attach (420) Wall Supports to (411) Swing Side Uprights with 2 (S3) #8 x 2-1/2” Wood Screws per support.
  • Page 93 Step 44: Attach Transom Assembly Part 1 A: Place 1 Transom Assembly on both (051) Front Wall Panel and (052) Back Wall Panel so they are tight to (410) Swing Top and (420) Wall Supports. From the outside attach each Transom Assembly to (420) Wall Supports with 2 (S3) #8 x 2-1/2”...
  • Page 94 Step 44: Attach Transom Assembly Part 2 D: Attach the top of each MOD 5 Pane Window to each (400) TB Support with 1 (S0) #8 x 7/8” Truss Screw per window then attach bottom of windows to (051) Front Wall Panel and (052) Back Wall Panel with 2 (S0) #8 x 7/8” Truss Screws per window .
  • Page 95 Step 45: Attach Mid Roof Ends A: Flush to the tops of (041) Narrow Back Panel and (042) Narrow Front Panel and flush to the outside edge of each Transom Assembly attach 1 (450) Mid Roof End per panel with 1 (S11) #8 x 2” Wood Screw in the bottom hole and 1 (S3) #8 x 2-1/2”...
  • Page 96 Step 46: Attach Roof End Shorts A: On (040) Slide End Panel place 1 (460) Roof End Short at each end flush to the top of the panel and each overhanging by 1-7/8” then attach with 2 (S11) #8 x 2” Wood Screws into the panel and 1 (S3) #8 x 2-1/2” Wood Screw into the front and back panels.
  • Page 97 Step 47: Attach Small Roof Assembly Part 1 A: With 2 people on the ground and at least 1 person in the fort, lift Small Roof Assembly up and over the Back side of the fort. Guide the Small Roof Assembly onto the fort so the ends of the Small Roof Support Assembly sit flush to the front and ends of each (460) Roof End Short.
  • Page 98 Step 47: Attach Small Roof Assembly Part 2 C: Attach Mid Roof Support Assembly to Transom Assemblies with 2 (S3) #8 x 2-1/2” Wood Screws. (fig. 47.3) Transom Fig. 47.3 Assembly Mid Roof Support Assembly Transom Assembly Hardware #8 x 2-1/2” Wood Screw...
  • Page 99 Step 48: Attach Long Roof Ends A: Place 1 (480) Long Roof End tight to each (390) Mid Roof Support and flush to the top of the Transom Assembly. Make sure (480) Long Roof End is level and the overhang at each end measures 4-1/4”, then attach to (390) Mid Roof Supports with 1 (S3) #8 x 2-1/2”...
  • Page 100 Step 49: Attach Transom Boards A: Tight to 1 Transom Assembly and flush to the bottom of (390) Mid Roof Support attach 1 (490) Transom Board A to (390) Mid Roof Support and (480) Long Roof End with 4 (S20) #8 x 1-3/8” Wood Screws. (fig. 49.1 and 49.2) B: Tight to (490) Transom Board A and flush to the bottom of (390) Mid Roof Support attach 1 (491) Transom Board B to (390) Mid Roof Support and (480) Long Roof End with 4 (S20) #8 x 1-3/8”...
  • Page 101 Step 50: Attach Large Roof Assembly A: With 2 people on the ground and at least 1 person in the fort, lift the Large Roof Assembly up and over the Back side of the fort. Guide the Roof Assembly onto the fort so all four (340) Roof Supports sit flush to the front and outside edges of (410) Swing Top and each (480) Long Roof End.
  • Page 102 Step 51: Attach Swings A: Using 1 Threaded Quick Link per chain, join 1 Long Swing Chain to each side of the Swing Belt Seat. Make sure to close the Threaded Quick Link tightly using an adjustable wrench. (fig. 51.1 and 51.2). B: Using 1 Threaded Clip per chain, join the Short Swing Chain to the Acro Bar and Acro Handle.
  • Page 103 Step 52: Attach Telescope A: On the front, centre of the Crowsnest, attach Telescope to (200) Crowsnest Top with 2 (S20) #8 x 1-3/8” Wood Screws. (fig. 52.1 and 52.2) Fig. 52.1 Fig. 52.2 Telescope Hardware Other Parts #8 x 1-3/8” Wood Screw 1 x Telescope...
  • Page 104 Step 53: Attach Steering Wheel A: On (050) SW Wall Panel attach Steering Wheel with 1 (WB10) 5/16 x 2-5/8” Wafer Bolt (with flat washer x 2 and lock nut). The bolt is attached from the outside of the assembly. (fig. 53.1 and 53.2) Fig.
  • Page 105 Step 54: Attach Slide to Fort Note: Pre-drill all holes using a 1/8” drill bit before installing the pan screws. A: Place Slide centred in the opening of the (051) Front Wall Panel. Slide must be tight to the outside of (051) Front Wall Panel.
  • Page 106 Step 55: Assemble and Attach Bell A: Centred under the peak of the Bell Support Assembly attach Horseshoe Mount to (042) Narrow Front Panel with 4 (S0) #8 x 7/8” Truss Screws. (fig. 55.1, 55.2 and 55.3) B: Thread the Steel Clapper Line through the Bolt. Slide Bell under overhang of Horseshoe Mount then insert Bolt up through Bell and Horseshoe Mount then secure with Nut.
  • Page 107 Step 56: Assemble and Attach BBQ Kitchen Part 1 A: On (051) Front Wall place BBQ Base on (131) Table Top. Use BBQ Cooktop as a guide so there is enough room for BBQ Cooktop and 1” gap to the edge of the wall to the left of BBQ Base. Attach BBQ Base to (131) Table Top with 4 (S0) #8 x 7/8”...
  • Page 108 Step 56: Assemble and Attach BBQ Kitchen Part 2 C: Slide BBQ Cooktop tight beside BBQ Base on the left and BBQ Sink Set tight on the right. Attach both BBQ Cooktop and BBQ Sink Set to (131) Tabel Top with 2 (S0) #8 x 7/8” Truss Screws each. (fig. 56.5, 56.6, 56.7 and 56.8) D: Place Faucet and 2 Sink Knobs in opening of Sink and attach Sink Knobs with included hardware.
  • Page 109 Step 57: Attach Utensil Shelves Part 1 A: From outside the assembly in the top of the opening of (051) Front Wall Panel, 1” in from the panel, attach 1 Utensil Shelf with 2 (S0) #8 x 7/8” Truss Screws as shown in fig. 57.1, 57.2 and 57.3. B: Attach Sign to the Utensil Shelf.
  • Page 110 Step 57: Attach Utensil Shelves Part 2 C: From outside the assembly, centred below the BBQ Kitchen attach 1 Utensil Shelf to (130) Table Support with 2 (S0) #8 x 7/8” Truss Screws as shown in fig. 57.4 and 57.5. D: Attach Pan, Tongs and Spatula to the Utensil Shelf.
  • Page 111 Step 58: Attach Flags A: Insert 1 Flag into slots on 1 Flag Pole to complete 1 Deluxe Flying Flag as shown in fig. 58.1. Create 2 Deluxe Flying Flags. B: Place 1 Deluxe Flying Flag on either side of the Telescope and attach to (200) Crowsnest Top with 2 (S0) #8 x 7/8”...
  • Page 112 4 (S37) #7 x 5/8” Pan Screws as shown below. I.D. Plaque - KK Other Parts Hardware #7 x 5/8” Pan Screw 1 x I.D. Plaque - KidKraft...
  • Page 113 NOTES...
  • Page 114 Would you recommend the purchase of our products to friends and family? Comments: MAIL TO: Fill out your registration card online at KidKraft www.cedarsummitplay.com/ 4630 Olin Road registration Dallas, TX 75244 United States Cedar Summit by KidKraft would like to say Attention: Customer Service Thank You for your time and feedback.

Table of Contents