1. Manuals
  2. Brands
  3. KidKraft Manuals
  4. Play Sets & Playground Equipment
  5. Cedar Summit Timber Trail Playhouse
  6. Installation and operating instructions manual

KidKraft Cedar Summit Timber Trail Playhouse Installation And Operating Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
TIMBER TRAIL PLAYHOUSE FSC - P280099
INSTALLATION AND OPERATING INSTRUCTIONS
WARNING
OBSTACLE FREE SAFETY ZONE - 19' 9" x 17' 9" (6.02 x 5.41m)
CAPACITY - 4 Users Maximum, Ages 2 to 10. Weight Limit 110 lbs. (49.9 kg) per bench.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks.
WARNING. Only for domestic use.
5.41m
17' 9"
10 - 12 Hrs
10 - 12 Hrs
2-4 Hrs
1.5 - 2 Hrs
FOR FORT & SWING
FOR FORT & SWING
TWO PERSON
ASSEMBLY
9400099
Rev 07/25/2019
To reduce the risk of serious injury or death, you must read and follow these instructions.
Keep and refer to these instructions often and give them to any future owner of this play set.
Manufacturer contact information provided below.
6.02m
19' 9"
2.02m
6' 7.5"
FOR OUTDOOR FAMILY
DOMESTIC USE ONLY
Cedar Summit by KidKraft
4630 Olin Road
Dallas, TX 75244, United States
customersupport@kidkraft
Online Parts Replacement:
Cedarsummitplay . c om/parts-center-warranty-claim
Customer Service:
1(800) 933-0771 or (972) 385-0100
KidKraft Netherlands BV
Olympisch Stadion 29
1076DE Amsterdam, The Netherlands
Europe Customer Service: +31 (0)20 305 8620
europecustomerservice@kidkraft . c om
EU Online Parts Replacement: parts . k idkraft . e u

Table of Contents

Keys to Assembly Success . . . . . . . . . . . . . . . . . . .pg . 3
About Our Wood - Limited Warranty . . . . . . . .pg . 4
Battery Instruction and Warranty . . . . . . . . . . .pg . 5
Keys to Quick Assembly . . . . . . . . . . . . . . . . . . . . .pg . 6
Part ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .pg . 7
Step-By-Step Instructions . . . . . . . . . . . . . . . . . pg . 15
Installation of ID/Warning Plaque . . . . . . . . . pg . 69

Advertisement

Table of Contents
loading

Related Manuals for KidKraft Cedar Summit Timber Trail Playhouse

Summary of Contents for KidKraft Cedar Summit Timber Trail Playhouse

  • Page 1: Table Of Contents

    DOMESTIC USE ONLY Table of Contents ASSEMBLY Cedar Summit by KidKraft 4630 Olin Road Warnings and Safe Play Instructions . . . . . . . .pg . 2 Dallas, TX 75244, United States Instructions for Proper Maintenance .

  • Page 2: Warnings And Safe Play Instructions

    Warnings and Safe Play Instructions CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using this play system.

  • Page 3: Keys To Assembly Success

    Keys to Assembly Success Tools Required • Carpenters Level • Standard or Cordless Drill • Safety Glasses • Claw Hammer • Carpenters Square • Pencil • Adult Helpers • Tape Measure Part Identification Key Key Number: The first two digits 2X 012 Post 2 x 4 x 83”...

  • Page 4: About Our Wood - Limited Warranty

    Such use may lead to product failure and potential injury. Any and all public use will void this warranty. Cedar Summit by KidKraft disclaims all other representations and warranties of any kind, express or implied province to province. This warranty excludes all consequential damages, however, some states do not allow the...

  • Page 5: Battery Instruction And Warranty

    Battery Instruction and Warranty This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

  • Page 6: Keys To Quick Assembly

    Your Key To Quick Assembly SORTING WOOD PARTS INTO EACH ASSEMBLY STEP WILL SAVE TIME! Step Step Step SAVE TIME - TIP #1: Open box with wood parts and look for the Key Number stamped on the end of the wood part (see chart below). Sort each wood part into the different assembly steps.

  • Page 7: Part Id

    Part Identification (Reduced Part Size) 3pc. - 241 - 31.8 x 50.8 x 108.8mm - Small Post FSC - Box 1 - 48088077 1 1/4" x 2" x 4-5/16" 1pc. - 051 - 23.8 x 63.5 x 127mm - Door Stop FSC - Box 1 - 48087437 15/16 x 2-1/2 x 5"...
  • Page 8 Part Identification (Reduced Part Size) 4pc. - 141 - 25.4 x 69.9 x 727.4 mm - Windows support FSC - Box 1 - 48086337 1" x 2 3/4" x 28 5/8" 4pc. - 272 - 15.9x76.2x1069.8 mm - Box Side Panel FSC - Box 1 - 48088237 5/8"...
  • Page 9 Part Identification (Reduced Part Size) 1pc. - 192 1pc. - 193 Roof Panel LM FSC Roof Panel RM FSC Box 1 - 478082577 Box 1 - 478082677 28.6 x 654.1 x 871.1mm 28.6 x 654.1 x 871.1mm 1 1/8" x 25 3/4" x 34 5/16" 1 1/8"...
  • Page 10 Part Identification (Reduced Part Size) 1pc. - 162 - Right Small Door FSC 1pc. - 161 - Left Small Door FSC Box 1 - 478083005 Box 1 - 478082905 25.4 x 214.3 x 421.4mm 25.4 x 214.3 x 421.4mm 1" X 8 7/16" X 16 19/32" 1"...
  • Page 11 Part Identification (Reduced Part Size) 478081937 478081437 1pc. - 021 - Folded Panel Assembly FSC 478081837 Box 1 - 478085537 478081637 478081737 478081537 If you need to order parts, please order below part # S39 - 52013903 478081937 - Open Wall Right FSC - 1pc. 478081837 - Open Wall Left FSC - 1pc.
  • Page 12 Hardware Identification (Actual Size) 2pc. TN2 - 5/16" T- Nut (54503300) 2pc. 5/16 x 1" FW2 - 5/16" Flat Washer - (51103300) 2pc. WB1 - Wafer Bolt - (53613310) #8 x 7/8" 165pc. S0 - Truss Screw - (52933505) #8 x 1/2" 2pc.
  • Page 13 Part Identification (Reduced Part Size) 1x - Timber Trail Bracket (3200099) 1x - Bay Window Assembly Top Set (3320097) 1x - Narrow Angle Bracket (8pk) 1x - Jamb Mount (4pk) (3207832) (3207802) 1x - Magnetic Catch Kit (3200716) 1x - Bay Window Assembly Bottom Set (3320099) 1x - Door Handle (4pk) (3207711) - Larger Gas Burner...
  • Page 14 Part Identification (Reduced Part Size) 3x - MOD 8 Side Lite White (9330519) 2x - Big Triangle Window (9330518) 1x - Roof Water Sink (2pk) (3337851) 1x - New MOD4 Side Lite (2pk) (3330522) 2x - Flower Pot (9330333) 2x - Toybox End (9330334) - Mail Slot (9330509) 1x - Doorbell II, Door Trim Set (White)

  • Page 15: Step-By-Step Instructions

    Europe Customer Service: +31 (0)20 305 8620 Online Parts Replacement: europecustomerservice@kidkraft.com Cedarsummitplay.com/parts-center- EU Online Parts Replacement: parts.kidkraft.eu warranty-claim Customer Service: 1(800) 933-0771 or (972) 385-0100 Read the assembly manual completely, paying special attention to ANSI warnings; notes; and safety/maintenance information.
  • Page 16 Step 2: Frame Assembly Part 1 A: Place (021) Panel Assembly in the upright position and unfold all panels, making sure that the window openings are at the top. B: Check to make sure that the assembly is square then install 6 (S3) #8 x 2-1/2” Wood Screws in the Front Wall and Back Wall panels.
  • Page 17 Step 2: Frame Assembly Part 2 C: Place 1 (022) Side Tie along the bottom of each Side Wall so they are level and flush to the bottom of the (021) Panel Assembly. Attach using 4 (S15) #8 x 1-3/4” Wood Screws per board. (fig. 2.3, 2.4, 2.5) Fig.
  • Page 18 Step 3: Terrace Frame Assembly Part 1 A: Stand (031) Terrace Panel Assembly so that it’s in the upright position. Unfold the panels, making sure that the larger openings are at the top, check to make sure that the assembly is square. Install 3 (S3) #8 x 2-1/2” Wood Screws into each corner of the assembly as shown in figure 3.1 and 3.2.
  • Page 19 Step 3: Terrace Frame Assembly Part 2 B: Position (031) Terrace Panel Assembly against the open Side Wall so that it lines up with the inside of the Front and Back Wall Panels as shown in figure 3.4. C: Attach from the inside of (021) Panel Assembly using 3 (S3) #8 x 2-1/2” Wood Screws per side. (fig. 3.3, 3.4, 3.5, 3.6) Fig.
  • Page 20 Step 4: Attach Door Panel Accessories Part 1 A: On the left panel of (041) Door, measure 1” from the top and bottom then place 1 Door Hinge on each end. Attach using 3 (S37) #7 x 5/8” Pan Screws per hinge. (fig. 4.1, 4.2) B: On the right panel of (041) Door, measure 21-3/4”...
  • Page 21 Step 4: Attach Door Panel Accessories Part 2 D: On the back of (041) Door, measure 21-3/4” up from the bottom and attach Door Handle using 2 (S37) #7 x 5/8” Pan Screws so that it’s opposite to the front Door Handle. (fig. 4.6, 4.7) E: Measure 17-3/8”...
  • Page 22 Step 5: Attached Door Assembly to Frame Part 1 A: Place (041) Door in the front opening of (021) Panel assembly, making sure that there is a 5/8” space between the frame and the bottom of the door. Attach each hinge to (021) Panel Assembly using 3 (S37) #7 x 5/8” Pan Screws.
  • Page 23 Step 5: Attach Door Assembly to Frame Part 2 B: In the notched out opening of (051) Door Stop attach the Magnetic Catch using 2 (S38) #7 x 1-1/8” Pan Screws. (fig.5.4) Important: Use a hand held screw driver and DO NOT over tighten. C: On the inside of the assembly, attach (051) Door Stop to (021) Panel Assembly with 2 (S15) #8 x 1-3/4”...
  • Page 24 Step 6: Attach Windows A: From inside the assembly, place 1 MOD 8 Side Lite in each of the front window openings in (021) Panel Assembly. Attach each window using 8 (S0) #8 x 7/8” Truss Screws. (fig. 6.1, 6.2) Fig.
  • Page 25 Step 7: Attach Roof Supports Part 1 A: Using the notched out ends of the boards, fit (071) Open Panel Beam and (072) Roof Support together and attach using 1 (WB1) Wafer Bolts (with flat washer and t-nut). (fig 7.1) B: Repeat Step A to make a second roof support assembly.
  • Page 26 Step 7: Attach Roof Supports Part 2 C: On the open End Wall of (021) Panel Assembly, place a roof support assembly on each side with the (072) Roof Supports to the insides. Make sure that support assemblies are flush to the edge of the Front and Back Walls and attach using 2 (S4) #8 x 3”...
  • Page 27 Step 7: Attached Roof Supports Part 3 F: Place 1 (076) Terrace Top Short on each short side of (031) Terrace Panel Assembly making sure they are flush to the edges. Attach using 2 (S4) #8 x 3” Wood Screws per board. (fig. 7.3) G: Place (075) Terrace Top Long between the 2 (076) Terrace Top Shorts.
  • Page 28 Step 7: Attach Roof Supports Part 4 H: From inside the (021) Panel Assembly, install 2 (S3) #8 x 2-1/2” Wood Screws into each top corner of the open End Wall, attaching the (071) Open Panel Beams to the (076) Terrace Top Shorts. (fig. 7.4 & 7.5). Fig.
  • Page 29 Step 8: Attach Low Posts Part 1 A: On the Back Wall of (031) Terrace Assembly space 3 (081) Low Posts. Measure to ensure there is a distance of 2-3/4” between each post and attach using 4 (S20) #8 x 1-3/8” Wood Screws per board. (fig. 8.1 & 8.2) Fig.
  • Page 30 Step 8: Attach Low Posts Part 2 B: On the Side Wall of (031) Terrace Panel Assembly, space 8 (081) Low Posts making sure there is a measurement of 2-5/8” between each post. Attach using 4 (S20) #8 x 1-3/8” Wood Screws per board. (fig. 8.3, 8.4, 8.5) Fig.
  • Page 31 Step 9: Attach Bench Posts A: On the Back Wall of (021) Panel Assembly attach 8 (091) Chair Posts to the assembly with 4 (S20) #8 x 1-3/8” Wood Screws per board, making sure there is a measurement of 2-5/8” between each board. (fig. 9.1, 9.2, 9.3) Fig.
  • Page 32 Step 10: Attach Bench Support Part 1 A: From inside the (021) Panel Assembly, on the outside End Wall place 1 (101) Counter Post Bottom across the assembly making sure there is a measurement of 12-3/8” from the bottom of the panel to the top of (101) Counter Post Bottom.
  • Page 33 Step 10: Attach Bench Support Part 2 B: From the inside of (021) Panel Assembly, place (102) Chair Support against the back section of the inner Side Wall making sure there is a measurement of 12-3/8” from the bottom of the panel to the top of the board. Check to make sure the board is level, then attach using 4 (S15) #8 x 1-3/4”...
  • Page 34 Step 11: Attach Bench Assembly Part 1 A: Place 2 (111) Chair Bottoms across the assembly so they are resting on the (102) Chair Support and the (101) Counter Post Bottom. (fig. 11.1, 11.2, 11.3) B: Make sure that the (111) Chair Bottoms are flush to the ends of (102) Chair Support as shown in figure 11.2 and that there is a measurement of 11-5/32”...
  • Page 35 Step 11: Attach Bench Assembly Part 2 D: Evenly space 10 (112) Chair Tops across the (111) Chair Bottoms and attach each board using 4 (S20) #8 x 1-3/8” Wood Screws. (fig. 11.4, 11.5) Fig. 11.4 x 4 per board Fig.
  • Page 36 Step 12: Bay Window Assembly Part 1 A: Place all faucets, knobs, stove bases and burners into place as shown in fig. 12.1, fig. 12.4 and fig. 12.5. From under the Bottom Sections secure each item using a “c” clip. (Fig. 12.2 and Fig. 12.3) Two Handle Hot &...
  • Page 37 Step 12: Bay Window Assembly Part 2 B: Place kitchen assembly in the bay window opening as shown in fig. 12.7. Attach using 2 (S0) #8 x 7/8” Truss Screws. (fig. 12.6, 12.7) Fig. 12.7 x 1 per side Fig. 12.6 Outdoor Sink Bottom Sections Hardware...
  • Page 38 Step 12: Bay Window Assembly Part 3 C: In the 2 outside openings of the Bay Window Assembly Top Set place 1 (122) Bay Window Wide making sure that there is a gap measuring greater than 1/2” between the wall and the (122) Bay Window Wide. Install using 1 (S0) #8 x 7/8”...
  • Page 39 Step 12: Bay Window Assembly Part 4 E: With a helper, insert Outdoor Sink Top Assembly into the Bottom Sections as shown in fig. 12.12 and attach from underneath using 6 (S0) #8 x 7/8” Truss Screws. (Fig. 12.13) F: From inside the assembly install 4 (S0) #8 x 7/8” Truss Screws to secure the top of the assembly to the frame. (fig.12.14, 12.15) Fig.
  • Page 40 Step 12: Bay Window Assembly Part 5 G: Making sure to note the hole orientation, install 3 (123) Bay Window Supports to (101) Counter Post Bottom using 6 (S15) #8 x 1 -3/4” Wood Screws, checking to make sure that they are flush to the bottom of (101) Counter Post Bottom.
  • Page 41 Step 12: Bay Window Assembly Part 6 H: Place the Window Support Assembly so that the (101) Counter Post Bottom is against the side wall and the Kitchen Supports are underneath the Outdoor Sink Bottom Sections to support it. Make sure that all areas are level and attach the (101) Counter Post Bottom to the wall using 6 (S15) #8 x 1 -3/4”...
  • Page 42 Step 12: Bay Window Assembly Part 7 J: From inside the assembly hang Pot, Pan and Spatula from the hooks on the Bay Window Assembly Top Set (Fig.12.23) Fig. 12.23 Bay Window Assembly Top Set Spatula Other Parts 1 x Pan 1 x Pot 1 x Spatula...
  • Page 43 Step 13: Kitchen Platform Assembly Part 1 A: Place 3 (132) BBQ Uprights between 2 (131) BBQ Bottoms. Check to make sure the ends are flush and the assembly is square, then attach using 12 (S3) #8 x 2-1/2” Wood Screws. (fig. 13.1) Fig.
  • Page 44 Step 13: Kitchen Platform Assembly Part 2 B: From inside the Terrace position Platform Assembly along the back wall, making sure that it is 5/8” down from the (031) Terrace Panel Assembly. Check that the Platform Assembly is level and attach using 2 (S15) #8 x 1-3/4”...
  • Page 45 Step 13: Kitchen Platform Assembly Part 3 C: Place 1 (133) BBQ Support under each side of the Platform Support Assembly so that they’re flush to (132) BBQ Uprights and to the outside edges of (031) Terrace Panel Assembly. Attach using 2 (S3) #8 x 2-1/2” Wood Screws per board.
  • Page 46 Step 13: Kitchen Platform Assembly Part 4 D: Place 3 (134) BBQ Tops across the top of the Platform Assembly as shown in fig. 13.6. Attach using 6 (S1) #8 x 1-1/8” Wood Screws per board. (fig. 13.6) Fig. 13.6 x 6 per board Wood Parts...
  • Page 47 Step 14: Triangle Window Frame Assembly A: Place 2 (141) Window Supports together as shown in fig.14.1, making sure that the sharper angle is at the top. (Fig. 14.1) B: Making sure that the corners are flush, place (142) Window Bottom beneath the (141) Window Supports to create the Triangle Window Frame Assembly.
  • Page 48 Step 15: Attach Triangle Window Frame A: Place a Triangle Window Frame Assembly over each (074) Main Beam, making sure that they are flush to the edges as shown in fig.15.2. Attach using 4 (S24) #10 x 4” Wood Screws per assembly. (fig. 15.1, 15.2) Fig.
  • Page 49 Step 16: Attach Gate Panel Accessories Part 1 A: On the front of the (161) Small Door Left and the (162) Right Small Door measure 9-5/8” up from the ground and place Door handles in the location shown in fig. 16.1. Attach using 2 (S37) #7 x 5/8” Pan Screws per handle.
  • Page 50 Step 16: Attach Gate Panel Accessories Part 2 B: Measure 1-5/8” down from the top outside edges of the Gate Panels and attach Door Hinges using 3 (S37) #7 x 5/8” Pan Screws per hinge. (fig. 16.2 & 16.3) C: Place lower Door Hinges so they are flush to the bottom of the Gate Panels and attach using 3 (S37) #7 x 5/8”...
  • Page 51 Step 16: Attach Gate Panel Accessories Part 3 D: On the back of (161) Small Door Left and (162) Right Small Door place 1 Catch Plate on the inside of each panel so that it’s flush to the bottom. Attach each Catch Plate using 2 (S37) #7 x 5/8” Pan Screws. (fig. 16.4, 16.5) Fig.
  • Page 52 Step 17: Attach Gate Panel to Assembly Part 1 A: In the front opening of (031) Terrace Panel Assembly, measure 5/8” up from the bottom of the panel and attach (161) Small Door Left and (162) Right Small Door to (031) Terrace Panel Assembly using 3 (S37) #7 x 5/8”...
  • Page 53 Step 17: Attach Gate Panel to Assembly Part 2 B: In the notched out openings on (171) Door Stop Bottom install Door Catches using 2 (S38) #7 x 1-1/8” Pan Screws per Door Catch. (fig. 17.3) Fig. 17.3 Door Catch Other Parts Hardware Wood Parts...
  • Page 54 Step 17: Attach Gate Panel to Assembly Part 3 C: From inside (031) Terrace Panel Assembly, place (171) Door Stop Bottom along the bottom of the front panel so that it’s flush to the bottom and in position to meet the Catch Plates. Attach using 3 (S15) #8 x 1-3/4” Wood Screws.
  • Page 55 Step 18: Roof End Assembly A: With a helper, place 2 (181) Low Window Supports together so they form a peak over the (075) Terrace Top Long, making sure they are flush to the edges of the assembly. Attach using 3 (S3) #8 x 2-1/2” Wood Screws. (fig.
  • Page 56 Step 19: Roof Assembly Part 1 A: Position (192) Roof Panel LM and (193) Roof Panel RM with the slats facing up. Place panels together at the narrow ends making sure they’re flush. (fig. 19.2) B: Measure 2” up from the bottom of the panels then center and install 1 Jamb Mount using 4 (S0) #8 x 7/8” Truss Screws.
  • Page 57 Step 19: Roof Assembly Part 2 D: With a helper, place roof panel assemblies together so they create a peak as shown in fig. 19.4. Center 2 Narrow Angle Brackets over the slats and attach using 2 (S0) #8 x 7/8” Truss Screws per bracket. (fig. 19.4, 19.5) E: Flush 2 Narrow Angle Brackets to the edge of the slats and attach using 2 (S0) #8 x 7/8”...
  • Page 58 Step 20: Attach Roof to Frame Part 1 A: With a helper, lift the roof assembly over the (141) Window Supports and attach using 4 (S3) #8 x 2-1/2” Wood Screws per side. (fig. 20.1) x 4 per side Fig. 20.1 Hardware #8 x 2-1/2”...
  • Page 59 Step 20: Attach Roof to Frame Part 2 A: Place (201) Roof Panel LF and (202) Roof Panel RF over the (181) Low Window Supports so they meet at the peak and are tight to the large roof assembly.(fig.20.2 & 20.4) B: Attach panels to (181) Low Window Supports using 2 (S3) #8 x 2-1/2”...
  • Page 60 Step 21: Attach Clock Chalk Sign A: Install Clock Chalk Signs in both side openings of the left Side Wall, reversing sides as desired. Attach from the inside using 6 (S0) #8 x 7/8” Truss Screws per side. (fig. 21.2, 21.2) Fig.
  • Page 61 Step 22: Attach MOD 4 Side Lite A: From the inside of (021) Panel Assembly, place 2 MOD 4 Side Lites in the openings on the left Side Wall. Attach using 8 (S0) #8 x 7/8” Truss Screws per window. (fig. 22.1, 22.2) MOD 4 Fig.
  • Page 62 Step 23: Attach Triangle Windows Part 1 A: From inside (021) Panel Assembly place 1 Big Triangle Window in the opening on the Front and attach using 9 (S0) #8 x 7/8” Truss Screws. (fig. 23.1, 23.2 & 23.3) B: Repeat to install Big Triangle Window in the Back opening. Fig.
  • Page 63 Step 23: Attach Triangle Windows Part 2 C: In the upper opening under the Terrace Roof install 1 Side Frame Triangle Window from the inside using 12 (S0) #8 x 7/8” Truss Screws. (fig. 23.4, 23.5, 23.6) Fig. 23.4 Fig. 23.5 S0 x 12 Side Frame Triangle...
  • Page 64 Step 24: Canopy Assembly Part 1 A: Place 1 (241) Small Post over each support piece on the (242) Small Roof making sure they are flush. Attach using 6 (S11) #8 x 2” Wood Screws. (fig. 24.1) Fig.24.1 Flush Flush Flush Hardware Wood Parts...
  • Page 65 Step 24: Canopy Assembly Part 2 B: Place Canopy Assembly under the Big Triangle Window on the Front Wall. Attach assembly to (142) Window Bottom from the outside using 3 (S11) #8 x 2” Wood Screws, making sure to install screws on an angle. (fig. 24.2 &...
  • Page 66 Step 25: Attach BBQ A: Center BBQ over the Kitchen Platform Assembly and attach to the center (134) BBQ Top using 2 (S0) #8 x 7/8” Truss Screws per side. (fig. 25.1, 25.2) Fig. 25.1 BBQ Kitchen Set Fig. 25.2 x 2 per side Hardware...
  • Page 67 Step 26: Attach Doorbell A: From inside the assembly insert Door Bell into the hole in the Front Wall and attach with 2 (S38) #7 x 1-1/8” Pan Screws. (fig. 26.1, 26.2) B: On the outside of the assembly place Doorbell Trim over the hole in the Front Wall, then attach with 2 (S37) #7 x 5/8”...
  • Page 68 Step 27: Toybox Assembly A: Place 2 Toybox Ends upside down so the handles are at the bottom. Place 2 (272) Box Side Panels on each side between the Toybox Ends and fit 3 (271) Box Bottoms into the top. Attach using 4 (S13) #6 x 5/8” Pan Screws (with #8 washer) per board.

  • Page 69: Installation Of Id/Warning Plaque

    Step 28: Attach Flower Pot to Assembly A: Center 1 Flower Pot under each front window and attach using 2 (S0) #8 x 7/8” Truss Screws per side. (fig. 28.1, 28.2) Fig. 28.1 Flower Pot Fig. 28.2 x 2 per pot Hardware Other Parts #8 x 7/8”...
  • Page 70 Final: Attach Playhouse Plaque A: Center Playhouse Plaque above the gate opening on (031) Terrace Panel Assembly and attach using 2 (S5) #8 x 1/2” Pan Screws. (fig. 29.1, 29.2) Fig. 29.1 Fig. 29.2 Playhouse Plaque Hardware Other Parts #8 x 1/2” Pan Screw 1 x Playhouse Plaque...
  • Page 71 NOTES...
  • Page 72 Would you recommend the purchase of our products to friends and family? Comments: MAIL TO: Fill out your registration card online at KidKraft www.cedarsummitplay.com/ 4630 Olin Road registration Dallas, TX 75244 United States Cedar Summit by KidKraft would like to say Attention: Customer Service Thank You for your time and feedback.

This manual is also suitable for:

P280099

Table of Contents