Advertisement
Quick Links
R I C H M O N D L O D G E – F 2 5 6 8 5 X
INSTALLATION AND OPERATING INSTRUCTIONS
30'-7"
7'-6"
18'-7"
By
9405685X
Rev 04/13/2018
WARNING
Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE - 9.32 x 8.23 m (30' 7" x 27') area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 2.06 m (6' 9")
27'
CAPACITY - 10 Users Maximum, Ages 3 to 10; Weight Limit 49.9 kg (110 lbs.) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries,
day cares or parks.
Cedar Summit by KidKraft
4630 Olin Road
Dallas, TX 75244, United States
customersupport@kidkraft . c om
Online Parts Replacement:
Cedarsummitplay . c om/parts-center-warranty-claim
Customer Service:
1(800) 933-0771 or (972) 385-0100
KidKraft Netherlands BV
Olympisch Stadion 29
1076DE Amsterdam, The Netherlands
Europe Customer Service: +31 (0)20 305 8620
europecustomerservice@kidkraft . c om
EU Online Parts Replacement: parts . k idkraft . e u
To reduce the risk of serious injury or death, you must read and
follow these instructions. Keep and refer to these instructions
often and give them to any future owner of this play set.
Table of Contents
Warnings and Safe Play Instructions . . . . . . . . . . pg . 2
Protective Surfacing Guidelines . . . . . . . . . . . . . . . pg . 3
Instructions for Proper Maintenance . . . . . . . . . pg . 4
About Our Wood – Limited Warranty . . . . . . . . . pg . 5
Keys to Assembly Success . . . . . . . . . . . . . . . . . . . . pg . 6
Part ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg . 8
Step-By-Step Instructions . . . . . . . . . . . . . . . . . . .pg . 18
Installation of I . D . / Warning Plaque . . . . . .Final Step
10 - 12 Hrs
FOR FORT & SWING
TWO PERSON
ASSEMBLY
Advertisement
Related Manuals for KidKraft Cedar Summit RICHMOND LODGE
Summary of Contents for KidKraft Cedar Summit RICHMOND LODGE
- Page 1 TWO PERSON ASSEMBLY Table of Contents Cedar Summit by KidKraft 4630 Olin Road Dallas, TX 75244, United States Warnings and Safe Play Instructions . . . . . . . . . . pg . 2 customersupport@kidkraft .
- Page 2 Warnings and Safe Play Instructions CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using this play system.
- Page 3 Protective Surfacing - Reducing Risk of Serious Head Injury From Falls One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM F1292.
- Page 4 Instructions for Proper Maintenance Your Cedar Summit Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important that you, the owner, properly maintain it.
- Page 5 Such use may lead to product failure and potential injury. Any and all public use will void this warranty. Cedar Summit by KidKraft disclaims all other representations and warranties of any kind, express or implied province to province. This warranty excludes all consequential damages, however, some states do not allow the...
- Page 6 Keys to Assembly Success Tools Required • Tape Measure • #1 Phillips, #2 Robertson • Open End Wrench • 3/16” Hex Key • Carpenters Level and Screwdriver (1/2” & 9/16”) • 8’ Step Ladder • Carpenters Square • Ratchet with extension •...
- Page 7 Your Key To Quick Assembly SORTING WOOD PARTS INTO EACH ASSEMBLY STEP WILL SAVE TIME! Step Step Step SAVE TIME - TIP #1: Open each box with wood parts and look for the Key Number stamped on the end of the wood part (see chart below). Sort each wood part into the different assembly steps.
- Page 10 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) 3638958 1pc. - 023 - 15.9 x 82.6 x 533.4 - Ladder Gap - Box 1 (1 x 4 x 21") 3638962 1pc.
- Page 11 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) 3632611 1pc. - 131 - 23.8 x 108 x 1006.5mm - Table Top 5/4 x 5 x 39-5/8" - Box 1 (5/4 x 5 x 39-5/8") 3638961 1pc.
- Page 12 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) 3638956 1pc. - 020 - 34.9 x 63.5 x 1336.5mm - Left Access - Box 2 (1-3/8 x 2½ x 52-5/8") 3632682 2pc.
- Page 13 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) 1pc. - 340 1pc. - 041 31.8 x 573.1 x 854.1mm 61.1 x 558.8 x 2209.8mm Front Small Roof Panel Back Narrow Panel 37632672 37638952...
- Page 14 Hardware Identification (Actual Size) 12pc. TN1 - 1/4" T - Nut 8pc. FW0 - 3/16" Flat Washer - (51103100) 5pc. LW2 - 5/16" Lock Washer - (51303300) (54503200) 20pc. LW1 - 1/4" Lock Washer - (51303200) 36pc. FW1 - 1/4" Flat Washer - (51103200) 8pc.
- Page 15 Hardware Identification (Actual Size) 1/4 x 2-1/2" 18pc. WL5 - Wafer Lag Wafer Bolt 5/16 x 3" 3pc. WB7 - - (53613330) - (52613222) Hex Bolt 1/4 x 4-1/4" 1pc. H8 - - (53703241) Hex Bolt 1/4 x 1-1/2" 4pc. H1 - - (53703212) Hex Bolt 1/4 x 2-3/4"...
- Page 16 Part Identification (Reduced Part Size) 1x - Cedar Summit 1x - TNR3 Extend Flange Rt ID Plaque - Bilingual (3310231) (Yellow) (9320359) 1x - Quadrex Driver (9200015) 1x - Cedar Summit Plaque (9320358) 2x - Rocks (4 Pk) (3320174) -Green/Yellow 2x - Steel Hand Grip 1x - Steering Wheel (9200211) -Yellow...
- Page 17 Europe Customer Service: +31 (0)20 305 8620 Online Parts Replacement: europecustomerservice@kidkraft.com Cedarsummitplay.com/parts-center-warranty-claim EU Online Parts Replacement: parts.kidkraft.eu Customer Service: 1(800) 933-0771 or (972) 385-0100 Read the assembly manual completely, paying special attention to ANSI warnings; notes; and safety/maintenance information on pages 1 - 6.
- Page 18 Step 1: Bench Assembly A: Open the Folding Bench Assembly. (fig. 1.1, 1.2 and 1.3) B: Make sure assembly is level then secure with 2 (H1) 1/4 x 1-1/2” Hex Bolts (with lock washer, flat washer and t-nut) per side. (fig. 1.4) C: Tighten the top screws in all 4 Bench Legs.
- Page 19 Step 2: Access Ladder / Rockwall Assembly Part 1 A: Place (020) Left Access on one side of 3 (022) Treads and (021) Right Access on the other side with the grooves facing in. (fig. 2.1) B: Fit each (022) Tread into grooves on both (020) and (021) Access rails, make sure the top edge of the (022) Treads are flush to the front of the Access rails.
- Page 20 Step 2: Access Ladder / Rockwall Assembly Part 2 D: Place (023) Ladder Gap on each access rail so there is a 2-3/8” gap between (023) Ladder Gap and the top (022) Tread. Attach using 4 (S11) #8 x 2” Wood Screws. (fig. 2.3) E: Place (024) Rock Rail on the ground next to (020) Left Access so it matches the orientation of the two access rails as shown in fig.
- Page 21 Step 3: Rockwall Assembly Part 1 A: Place (030) Access Board flush to the top of the Access Ladder/Rockwall Assembly and (031) Wall Board flush to the bottom of the assembly as shown in fig. 3.1. Then place (032) Rock Board A and (033) Rock Board B as shown in fig.
- Page 22 Step 3: Rockwall Assembly Part 2 C: Alternating colours and shapes, attach 1 rock to each rock board using 1 (PB2) 1/4 x 1-1/4” Pan Bolt (with lock washer, flat washer and barrel nut) and 1 (S10) #8 x 1” Pan Screw per rock. (fig. 3.2 and 3.3) The Pan Screw is placed in the hole beneath the Pan Bolt.
- Page 23 Step 4: Slide Wall Assembly A: Place (041) Back Narrow Panel against the left side of (040) SL Panel noticing panel orientation. The tops and bottoms of the panels should be flush and panels square. Pre-drill with a 3/16” drill bit, then fasten (041) Back Narrow Panel to (040) SL Panel with 4 (WL5) 1/4 x 2-1/2”...
- Page 24 Step 5: Swing Wall Assembly A: Place (051) Front Wall Panel against the left side of (050) SW Panel noticing panel orientation. The tops and bottoms of the panels should be flush and panels square. Pre-drill with a 3/16” drill bit, then fasten (051) Front Wall Panel to (050) SW Panel with 4 (WL5) 1/4 x 2-1/2”...
- Page 25 Step 6: Join Swing and Slide Wall Assemblies Part 1 A: With at least two helpers lift the Slide Wall Assembly and Swing Wall Assembly so the (041) Back Narrow Panel and (042) Front Narrow Panel meet with (052) Back Wall Panel and (051) Front Wall Panel and are tight together as shown in fig.
- Page 26 Step 6: Join Swing and Slide Wall Assemblies Part 2 C: From inside the assembly, tight to (040) SL Wall, Fig. 6.3 halfway up the assembly attach 1 (061) Side Joist to (041) Back Narrow Panel and (052) Back Wall Panel with 2 (H11) 1/4 x 2-3/4”...
- Page 27 Step 6: Join Swing and Slide Wall Assemblies Part 3 F: From inside the assembly, flush to the top of the assembly attach 1 (063) Wall Tie to (041) Back Narrow Panel and (052) Back Wall Panel and a second (063) Wall Tie to (042) Front Narrow Panel and (051) Front Wall Panel with 5 (S11) #8 x 2”...
- Page 28 Step 6: Join Swing and Slide Wall Assemblies Part 4 G: On the inside of the assembly attach (042) Front Narrow Panel to (051) Front Wall Panel using 2 Flat Panel Brackets in the places shown with 4 (S8) #12 x 3/4” Pan Screws per bracket. (fig. 6.8 and 6.9) H: Repeat Step G to attach (041) Back Narrow Panel to (052) Back Wall Panel.
- Page 29 Step 7: Floor Assembly Part 1 A: Place 1 (070) Floor Board tight to (040) SL Panel and attach to each (061) Side Joist with 4 (S2) #8 x 1-1/2” Wood Screws. Repeat for second (070) Floor Board tight to (050) SW Panel and attach to each (062) Short Side Joist.
- Page 30 Step 7: Floor Assembly Part 2 C: Starting at the Slide Wall place 8 (070) Floor Boards tight to the previously attached (070) Floor Board, followed by 1 (072) Floor Board then 3 more (070) Floor Boards. Make sure all boards are equally spaced then attach to (071) Long Floor Joist and each (061) Side Joist and (062) Short Side Joist with 5 (S2) #8 x 1-1/2”...
- Page 31 Step 8: Attach SW Table Tops A: In the opening in (051) Front Wall Panel, from the inside, attach (080) SW Table Top, tight to the corner of the panels with overhang facing in with 2 (S11) #8 x 2” Wood Screws from the top of the board and 1 (S11) #8 x 2” Wood Screw at each end as shown in fig.
- Page 32 Step 9: Attach SW Ground and Diagonal A: Loosely attach (090) SW Ground to (091) Diagonal with 1 (H10) 1/4 x 2-1/4” Hex Bolt (with lock washer, flat washer and t-nut) then place (091) Diagonal tight and flush to the front of (050) SW Panel. (090) SW Ground to be flush to the bottom of (050) SW Panel.
- Page 33 Step 10: Attach Access Ladder/Rockwall Assembly Part 1 A: Place Access Ladder/Rockwall Assembly from Step 3 against (051) Front Wall Panel, flush to the outside edge and flush to the top of the floor boards then attach with 4 (S2) #8 x 1-1/2” Wood Screws. (fig. 10.1 and 10.2) Fig.
- Page 34 Step 10: Attach Access Ladder/Rockwall Assembly Part 2 B: Place (030) Access Board from Step 3, Part 1 against (020) Left Access and (024) Rock Rail and flush to the tops then attach with 4 (S2) #8 x 1-1/2” Wood Screws. (fig. 10.3 and 10.4) Fig.
- Page 35 Step 10: Attach Access Ladder/Rockwall Assembly Part 3 C: Place (100) RW-AL Ground Brace flush to the end and bottom of (021) Right Access. Make sure the other end of the board is flush to the bottom of (050) SW Panel then attach with 2 (S11) #8 x 2” Wood Screws. (fig. 10.5 and 10.6) D: Attach other end of (100) RW-AL Ground Brace to (050) SW Panel with 2 (S11) #8 x 2”...
- Page 36 Step 11: Attach Steel Hand Grips to Fort A: Measure 6” from the top of (025) RW/AL Support on (051) Front Wall Panel in the 2 places shown below and attach 2 Steel Hand Grips with 2 (S6) #12 x 1” Pan Screws (with flat washer) per Steel Hand Grip. (fig. 11.1 and 11.2) Steel Hand Grip Fig.
- Page 37 Step 12: Door Panel Assembly Part 1 A: On the inside of (120) Door Window Panel measure 15” up from the bottom and attach Catch Plate flush to the edge using 2 (S18) #6 x 1” Wood Screws. (fig. 12.1 and 12.2) B: On the inside of (120) Door Window Panel measure 22”...
- Page 38 Step 12: Door Panel Assembly Part 2 C: On the outside of the (120) Door Window Panel attach the second Door Handle at approximately the same place as the one on the inside. Use 2 (S13) #6 x 5/8” Pan Screws. (fig. 12.3) D: Attach 2 Door Hinges on the outside of the (120) Door Window Panel on the opposite side from the Door Handle.
- Page 39 Step 12: Door Panel Assembly Part 3 E: In the opening for the door, measure 5/8” from the top of (042) Front Narrow Panel bottom and maximum 5/8” from right side of the opening which would be the Door Hinge side and attach the remaining side of the hinges to (042) Front Narrow Panel using 3 (S13) #6 x 5/8”...
- Page 40 Step 12: Door Panel Assembly Part 4 F: In the notched out opening of (121) Door Stop attach the Magnetic Catch using 2 (S18) #6 x 1” Wood Screws. (fig. 12.7) Important: Use a handheld screwdriver and DO NOT overtighten. G: On the inside of the assembly, attach (121) Door Stop to (042) Front Narrow Panel with 3 (S11) #8 x 2”...
- Page 41 Step 13: Back Wall Assembly Part 1 A: Place (130) Table Support flush to the notched out ends of (131) Table Top and attach with 4 (S7) #12 x 2” Pan Screws as shown in fig. 13.1. B: Place Table Top Assembly tight in the opening of (052) Back Wall Panel and attach (130) Table Support to (052) Back Wall Panel with 2 (S3) #8 x 2-1/2”...
- Page 42 Step 13: Back Wall Assembly Part 2 C: Place (132) Chalkwall Block flush to the inside edge of (131) Table Top and tight to left hand side of (052) Back Wall Panel then attach with 2 (S2) #8 x 1-1/2” Wood Screws. (fig. 13.4 and 13.5) D: From inside the assembly place Sky Chalk Wall tight to (132) Chalkwall Block and (052) Back Wall Panel then attach with 4 (S10) #8 x 1”...
- Page 43 Step 14: Swing Beam Assembly A: Attach 6 Swing Hangers to (140) Beam SW using 2 (G7) 5/16 x 5-1/2” Hex Bolts (with 2 flat washers and 1 lock nut) per swing hanger, as shown in fig. 14.1. B: Flush to the Fort Side end of (140) Beam SW attach 2 L-Beam Brackets with 2 (G21) 5/16 x 3-3/4” Hex Bolts (with 2 flat washers and 1 lock nut).
- Page 44 Step 15: Swing End Assembly A: Loosely attach 2 (150) Heavy SW Posts to (151) SW Upright using 2 (G7) 5/16 x 5-1/2” Hex Bolts (with lock washer, flat washer and t-nut). Notice 2 bolt holes at top of (151) SW Upright and orientation of angle. (fig. 15.1) B: Attach (152) SW Support to both (150) Heavy SW Posts and (151) SW Upright using 3 (G4) 5/16 x 4”...
- Page 45 Step 16: Attach Swing End to Swing Beam A: Place Swing End Assembly against Swing Beam Assembly then place 1 Beam Bracket on each side of the assembly (they are specific for left and right side) and attach with 5 (G21) 5/16 x 3-3/4” Hex Bolts (with 2 flat washers and 1 lock nut).
- Page 46 Step 17: Attach Swing Assembly To Fort A: Place Swing Assembly against top of (050) SW Panel, make sure assembly is level then attach from inside the fort assembly into each L-Beam Bracket with 4 (G27) 5/16 x 1 ¾” Hex Bolts (with 2 flat washers and 1 lock nut).
- Page 47 Step 18: Install Ground Stakes MOVE FORT TO FINAL LOCATION PRIOR TO STAKING FINAL LOCATION MUST BE LEVEL GROUND A: In the 5 places shown in fig. 18.1 drive the Rebar Ground Stakes 33 cm (13”) into the ground against (040) SL Panel, on the Front, (091) Diagonal, (021) Right Access and both (150) Heavy SW Posts.
- Page 48 Step 19: Slide Section Assemblies Part 1 Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess. (fig. 19.3) A: Fit 2 TNR2 Slide Elbows together and attach with 8 (PB1) 1/4 x 3/4”...
- Page 49 Step 19: Slide Section Assemblies Part 2 Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess. (fig. 19.3) D: Attach TNR2 Slide Exit Top and the remaining TNR2 Slide Elbow together using 8 (PB1) 1/4 x 3/4”...
- Page 50 Step 20: Attach Flange Assembly to Fort Part 1 A: With a helper place the Flange Assembly flush to the top opening in (040) SL Panel as shown in fig. 20.1, then pre-drill 1/8” pilot holes in the bottom 4 mounting locations (approximate spots where circles are on figure), making sure the pre-drilled holes are a minimum of 2.5 cm (1”) deep.
- Page 51 Step 20: Attach Flange Assembly to Fort Part 2 D: Place (200) SL Gusset tight to (040) SL Panel, flush to the top of the bottom opening and attach to Flange Assembly with 2 (S6) #12 x 1” Pan Screws. (fig. 20.4 and 20.5) E: Pre-drill pilot hole with a 3/16”...
- Page 52 Step 21: Attach Elbow Assembly to Flange Assembly Part 1 Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess. Keep all bolts loose until further step.
- Page 53 Step 21: Attach Elbow Assembly to Flange Assembly Part 2 Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go Fig. 21.5 through the side with the hexagonal recess. Keep all bolts loose until further step.
- Page 54 Step 22: Attach Elbow Assembly to Elbow Assembly Part 1 Note: When installing Pan Bolts make sure to look at holes so bolts go Fig. 22.1 through the side with the round recess and the lock nuts go through the side with the hexagonal recess. Keep all bolts loose until further step.
- Page 55 DO NOT USE DO NOT USE Step 22: Attach Elbow Assembly to Elbow Assembly USE IMAGE PG 125 USE IMAGE PG 125 Part 2 Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess.
- Page 56 Step 23: TNR Brace Assembly A: Attach (231) TNR Upright to (230) TNR Ground Brace with 1 (H8) 1/4 x 4-1/4” Hex Bolt (with lock washer, flat washer and t-nut) in the top hole. Make sure both boards are square then attach with 1 (S11) #8 x 2”...
- Page 57 Step 24: Attach Elbow Assemblies and TNR2 Slide Support Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess. Keep all bolts loose until further step.
- Page 58 Step 25: Attach TNR Brace Assembly A: Use (231) TNR Upright as a guide to judge the proper bolt location, remove the bottom pan bolt and nut. The bolt will no longer be needed, but keep the lock nut. (fig. 25.1 and 25.2) B: Attach the top of the TNR3 Post Mount to TNR2 Slide Clamp Ring using 1 (PB2) 1/4 x 1-1/4”...
- Page 59 Step 26: Attach TNR2 Slide Exit to Exit Elbow Assembly A: Insert flange of Exit Elbow Assembly (slide elbow) into the slots on TNR3 Short Exit. (fig. 26.1) B: Rotate Slide Exit and use Quadrex Driver as a guide pin so the holes are aligned and attach with 5 (PB1) 1/4 x 3/4”...
- Page 60 Step 27: Attach Exit End Assembly to Fort Note: When installing Pan Bolts make sure to look at Fig. 27.1 Top Slide Bolt Holes Exit Elbow Assembly holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess.
- Page 61 Step 28: Attach Ground Stake to TNR Upright A: In the spot shown in fig. 28.1 drive 1 Rebar Ground Stake 33 cm (13”) into the ground against the (231) TNR Upright. Be careful not to hit the washer while hammering stake into the ground as this could cause the washer to break off.
- Page 62 Step 29: Attach Swing Wall Roof Ends A: Place 1 (290) Roof End flush to the top of (050) SW Panel on the right hand side, measure overhang so it is 12.38 cm (4-7/8”) then attach with 2 (S11) #8 x 2” Wood Screws and 1 (S4) #8 x 3” Wood Screw. (fig. 29.1 and 29.2) B: Repeat Step A for 1 (291) Roof End Left.
- Page 63 Step 30: Attach Slide Wall Roof Ends A: Place 1 (290) Roof End flush to the top of (040) SL Panel on the right hand side, measure overhang so it is 6.7 cm (2-5/8”) then attach with 3 (S11) #8 x 2” Wood Screws. (fig. 30.1 and 30.2) B: Repeat Step A for 1 (291) Roof End Left.
- Page 64 Step 31: Attach Mid Roof Ends A: Measure 54.9 cm (21-5/8”) in from the outside edge and 3.175 cm (1-1/4”) down from the top of (042) Front Narrow Panel then pre-drill with a 3-16” drill bit. Place 1 (310) Mid Roof End flush to the top and inside frame of (042) Front Narrow Panel, over the pre-drilled hole and attach top from the inside with 1 (S4) #8 x 3”...
- Page 65 Step 32: Roof Support Assembly A: Attach 1 (320) Roof Support to a second (320) Roof Support at peak using 1 (S4) #8 x 3” Wood Screw. Repeat this twice so there are 2 Large Roof Supports Assemblies. (fig. 32.1) B: Attach 1 (321) Roof Support to a second (321) Roof Support at peak using 1 (S4) #8 x 3”...
- Page 66 Step 33: Large Roof Assembly Part 1 A: Place (330) Front Roof Panel against (331) Back Roof Panel so the tops form a peak then tight to the inside edge of the outside slats attach 1 Narrow Angle Bracket per slat with 2 (S13) #6 x 5/8” Pan Screws per bracket. (fig.
- Page 67 Step 33: Large Roof Assembly Part 2 C: Place 1 Large Roof Support Assembly against one side so the peaks meet and the ends of the roof supports are flush with the ends of the roof panels. Attach with 6 (S11) #8 x 2” Wood Screws. (fig. 33.4) D: Attach the second Large Roof Support Assembly on the opposite side, peaks to meet and ends are flush with 6 (S11) #8 x 2”...
- Page 68 Step 34: Small Roof Assembly Part 1 A: Tight to the inside edge of the outside slats attach 1 Narrow Angle Bracket per slat with 2 (S13) #6 x 5/8” Pan Screws per bracket. (fig. 34.1) B: Place (340) Front Small Roof against (341) Back Small Roof so the tops form a peak then place Small Roof Support Assembly against one side so the peaks meet and the ends of the roof supports are flush with the ends of the roof panels.
- Page 69 Step 34: Small Roof Assembly Part 2 C: Tight to (340) Front Small Roof and (341) Back Small Roof attach (370) Bottom Gable to each (321) Roof Support with 4 (S2) #8 x 1-1/2” Wood Screws. (fig. 34.2) Fig. 34.2 Tight Tight Wood Parts...
- Page 70 Step 35: Attach Roof Assemblies to Fort Part 1 A: With 2 people on the ground and at least 1 person in the fort, lift the Large Roof Assembly up and over the Back side of the fort. Guide the Large Roof Assembly onto the Swing Wall side of the fort so all four (320) Roof Supports sit flush to the front and outside edges of (290) Roof End, (291) Roof End Left and both (310) Mid Roof Ends.
- Page 71 Step 35: Attach Roof Assemblies to Fort Part 2 C: With 2 people on the ground and at least 1 person in the fort, lift the Small Roof Assembly up and over the Back side of the fort. Guide the Small Roof Assembly onto the fort so it slides under the Large Roof Assembly and the (320) Roof Supports sit tight to the siding on the Small Roof Assembly.
- Page 72 Step 35: Attach Roof Assemblies to Fort Part 3 E: Attach (320) Roof Supports to both (310) Mid Roof Ends with 1 (S3) #8 x 2-1/2” Wood Screw per support. (fig. 35.6 and 35.7) F: Attach (321) Roof Supports to (290) Roof End and (291) Roof End Left with 1 (S3) #8 x 2-1/2” Wood Screw per support.
- Page 73 Step 36: Attach Peak Detail A: Attach 1 Peak Detail to the inside of (320) Roof Supports on the Large Roof Assembly and (321) Roof Supports on the Small Roof Assembly with 8 (S8) #12 x 3/4” Pan Screws (with 1/4” flat washer) per Peak Detail. (fig.
- Page 74 Step 37: Attach Steering Wheel A: On the back upright of (050) SW Panel attach Steering Wheel to (050) SW Panel with 1 (H11) 1/4 x 2-3/4” Hex Bolt (with flat washer x 2 and lock nut). (fig. 37.1 and 37.2) Back Fig.
- Page 75 Step 38: Attach Swings A: Using 1 Threaded Clip per chain, join 1 Long Swing Chain to each side of the swing belt seat. Make sure to close the Threaded Clip tightly using an adjustable wrench. (fig. 38.1 and 38.2). B: Using 1 Threaded Clip per chain, join the Short Swing Chain to the Acro Bar and Acro Handle.
- Page 76 Final Step: Attach I.D. Plaque ATTACH THIS WARNING & I.D. PLAQUE TO THIS LOCATION ON YOUR PLAY EQUIPMENT! This provides warnings concerning safety and important contact information. A Tracking Number is provided to allow you to get critical information or order replacement parts for this specific model. ATTACH THIS WARNING &...
- Page 77 NOTES...
- Page 78 Would you recommend the purchase of our products to friends and family? Comments: MAIL TO: Fill out your registration card online at KidKraft www.cedarsummitplay.com/ 4630 Olin Road registration Dallas, TX 75244 United States Cedar Summit by KidKraft would like to say Attention: Customer Service Thank You for your time and feedback.