Download
Share
Print this page
KidKraft CRANBROOK PLAY SYSTEM Installation And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. KidKraft Manuals
  4. Play Sets & Playground Equipment
  5. CRANBROOK PLAY SYSTEM
  6. Installation and operating instructions manual

KidKraft CRANBROOK PLAY SYSTEM Installation And Operating Instructions Manual

Hide thumbs

Advertisement

Quick Links

C R A N B R O O K P L AY S Y S T E M - F 2 3 8 7 0
INSTALLATION AND OPERATING INSTRUCTIONS
26'-10"
13'-5"
13'-5"
CRANBROOK
Dimensions as per JIM/BEN - Mar.31/2014
HEIGHT: 10ft - 3"
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244 USA
customerservice@kidkraft.com
canadacustomerservice@kidkraft.com
1.800.933.0771
972.385.0100
For online parts replacement visit
https://parts.kidkraft.com/
WARNING
and give them to any future owner of this play system. Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE - 26'10" x 26'10" area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6'5" (1.98 m)
26'-10"
CAPACITY - 11 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks.
Warning. Only for domestic use.
KidKraft Netherlands BV
Olympisch Stadion 8
1076 DE Amsterdam
The Netherlands
europecustomerservice@kidkraft.com
+31 20 305 8620 M-F from 09:00 to 17:30
(GMT+1)
For online parts replacement visit
https://parts.kidkraft.eu/
To reduce the risk of serious injury or death, you must read and
follow these instructions. Keep and refer to these instructions often

Table of Contents

Warnings and Safe Play Instructions. . . . . . . . . . . . . . . pg. 2
Protective Surfacing Guidelines. . . . . . . . . . . . . . . . . . . pg. 3
Instructions for Proper Maintenance . . . . . . . . . . . . . . . pg. 4
About Our Wood - Limited Warranty . . . . . . . . . . . . . . pg. 5
Keys to Assembly Success . . . . . . . . . . . . . . . . . . . . . . pg. 6
Metric Conversion Sheets . . . . . . . . . . . . . . . . . . . . . pg. 7,8
Part ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 9
Installation of I.D./Warning Plaque . . . . . . . . . . . .Final Step
9403870
8 - 10 Hrs
Two person
assembly
Rev 04/13/2021

Advertisement

loading

Related Manuals for KidKraft CRANBROOK PLAY SYSTEM

Summary of Contents for KidKraft CRANBROOK PLAY SYSTEM

  • Page 1: Table Of Contents

    Protective Surfacing Guidelines....pg. 3 Instructions for Proper Maintenance ....pg. 4 KidKraft, Inc. KidKraft Netherlands BV 4630 Olin Road Olympisch Stadion 8 About Our Wood –...

  • Page 2: Warnings And Safe Play Instructions

    Warnings and Safe Play Instructions CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using this play system.

  • Page 3: Protective Surfacing Guidelines

    Protective Surfacing - Reducing Risk of Serious Head Injury From Falls. One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM F1292.

  • Page 4: Instructions For Proper Maintenance

    Instructions for Proper Maintenance Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important that you, the owner, properly maintain it.

  • Page 5: About Our Wood - Limited Warranty

    About Our Wood KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use. Although we take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible to weathering which can change the appearance of your set.

  • Page 6: Keys To Assembly Success

    Keys to Assembly Success Tools Required • Tape Measure • #1, #2 & #3 Phillips • Open End Wrench • 3/16” Hex Key • Carpenters Level or Robertson Bits (7/16”, 1/2” & 9/16”) • 8’ Step Ladder • Carpenters Square or Screwdriver •...

  • Page 9: Part Id

    Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Actual Size Nominal Size 1 pc. - 2430 - Clock Siding 3/8 x 3 1/2 x 12-1/8 "  ‐  Box 4  ‐ 3632430 " x 3¼" ½...
  • Page 10 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Actual Size Nominal Size 1 pc. - 2560 - Lower Bench 1 x 4 x 37 5/8 " - Box 2 - 3632560 "...
  • Page 11 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Nominal Size Actual Size 1 pc. - 2558 - Ground Back 1 x 5 x 68"  ‐  Box 2  ‐ 3632558 5/4" x 4" 1" x 3½" 5/4"...
  • Page 12 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Nominal Size Actual Size 1 pc. - 0376 - Table Top 5/4 x 6 x 32 " - Box 2 - 3640376 5/4"...
  • Page 13 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Nominal Size Actual Size 2 pc. - 2382 - MK Post 2 x 3 x 77 1/2 "  ‐  Box 2  ‐ 3632382 5/4" x 4" 1"...
  • Page 14 Part Identification (Reduced Part Size) 1X 9320240 Hand Grip -Yellow 1X 3320124 Clock Assembly 1X 3201710 Door Hardware 2X 9207713 Magnetic Door Catch 1X 3200202 Glider Hanger (2pk) 1X 3310148 Slide 48" High Rail -Yellow 2X 9201716 2X 9201712 Door Handle Door Hinge 1X 3320386 Rocks (5pk) 3-Green 2-Yellow...
  • Page 15 Hardware Identification (Actual Size) 1/4 x 1-1/2" 9pc. LS1 - Lag Screw 1/4 x 2-1/2" - (9262212) 2pc. LS2 - Lag Screw - (9272222) 1/4 x 3" 6pc. LS3 - Lag Screw - (9262230) Hex Bolt 1/4 x 2" 28pc. H2 - - (9277220) Hex Bolt 1/4 x 2-1/2"...
  • Page 16 Hardware Identification (Actual Size) 15pc. LW2 - 16 " Lock Washer - (9253300) 5pc. BN1 -1/4" Barrel Nut (9248200) 91pc. FW1 -1/4" Flat Washer - (9251200) 75pc. LW1 -1/4" Lock Washer - (9253200) 70pc. TN1 - 1/4" T - Nut (9285200) 34pc.
  • Page 17 Before you discard your cartons fill out the form below. • The carton I.D. stamp is located on the end of each carton.The tracking number is located on the KidKraft ID Plaque (9320374). • Please retain this information for future reference. You will need this information if you contact the Consumer Relations Department.
  • Page 18 Step 2: Rock Wall Assembly Fig. 2.1 Note: The 2330 2330 holes in the 0702 rock boards 2257 2555 must orient to 2257 2257 x 4 per the top of the board boards. 8-1/4” Note: Gaps between Approx boards 2-3/4” A: Lay 2 (2555) Rock Rails down, side by side with angled edges facing down.
  • Page 19 Step 3: Swing Beam Assembly WARNING: Fig. 3.4 For your child’s safety, orientate the swing hangers as shown to ensure your swing will have proper swing motion when installed. Failure to do so could result in premature failure of the swing hanger or swing chain.
  • Page 20 Step 4: Swing End Assembly A: Attach 2 (1863) SW Posts to (1856) SW Upright using 2 (G4) 5/16 x 4” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 4.1) Fig. 4.1 5/16” Lock 1863 Washer 1856 5/16” Flat Washer 5/16”...
  • Page 21 Step 5: Attach Swing End to Swing Beam A: Place (4919) SW Rail Block in the centre between (1826) Front Beam and (1825) Back Beam and attach with 1 (H8) 1/4 x 4-1/4” Hex Bolt (with lock washer, flat washer and t-nut). (fig. 5.1 and 5.2) Fig.
  • Page 22 Step 6: Door Assembly Part 1 A: On the inside of (8197) Door Panel, measure 19” up from the bottom then attach Catch Plate flush to the edge using 2 (S18) #6 x 1” Wood Screws. (fig. 6.1 and 6.2) B: On the inside of (8197) Door Panel beside the Catch Plate attach 1 Door Handle using 2 (S13) #6 x 5/8”...
  • Page 23 Step 6: Door Assembly Part 2 C: On the outside of the (8197) Door Panel attach the second Door Handle at approximately the same place as the one on the inside. Use 2 (S13) #6 x 5/8” Pan Screws. (fig. 6.3) D: In the window opening of (8197) Door Panel insert 1 Small Window from the outside and attach with 8 (S13) #6 x 5/8”...
  • Page 24 Step 7: Roof Assembly Part 1 A: Attach 1 (2394) Roof Support to another at the peak using 1 (S4) #8 x 3” Wood Screw. Do this twice so you have 2 Roof Support Assemblies. (fig. 7.1) B: Attach 1 (2417) Joist to another at the peak using 1 (S4) #8 x 3” Wood Screw. (fig. 7.1) Fig.
  • Page 25 Step 7: Roof Assembly Part 2 C: Starting at the top of the Roof Support Assembly attach 1 (2421) Cedar Roofing on each side of the Roof Support Assemblies with 3 (S0) #8 x 7/8” Truss Screws per board. (fig. 7.2) Be sure to overlap the top of the boards so there are no gaps.
  • Page 26 Step 8: Monkey Rail Assembly Pre-drill all pilot holes using a 1/8” drill bit before installing Wood Screws. A: Insert 3 (578) 1-1/8 x 15-7/8” Dowels into both (1565) MK Rail Shorts as shown in fig. 8.1. Note the pilot holes in one of the (1565) MK Rail Short are on the bottom of the board.
  • Page 27 Step 9: Monkey Ladder Assembly Note: Pre-drill all holes using a 1/8” drill bit before installing the Lag Screws and Wood Screws. A: Insert 2 (858) 1-1/8 x 18-5/8” Dowels into 2 (2382) MK Posts as shown in fig. 9.1. Fig.
  • Page 28 Step 10: Connect Monkey Bar Assemblies Note: Pre-drill all holes using a 1/8” drill bit before installing the Pan Screws. A: Using a Monkey Bracket connect both (1565) MK Rail Shorts to each (2382) MK Post with 1 (G10) 5/16 x 3”...
  • Page 29 Step 11: Access Wall Assembly Note: Pre-drill all holes using a 1/8” drill bit before installing the Lag Screws. A: On the ground lay flat 2 (2383) Posts then loosely attach (0348) SL Ground with 4 (H2) 1/4 x 2” Hex Bolts (with lock washer, flat washer and t-nut);...
  • Page 30 Step 12: Cafe Wall Assembly Note: Pre-drill all holes using a 1/8” drill bit before installing the Lag Screws. A: On the ground lay flat 2 (2383) Posts then loosely attach (0348) SL Ground with 4 (H2) 1/4 x 2” Hex Bolts (with lock washer, flat washer and t-nut);...
  • Page 31 Step 13: Front Wall Assembly A: With both the Access and Cafe Walls facing each other loosely Fig. 13.1 1/4” attach (2554) Front Ground to (2383) t-nut Posts with 2 (H4) 1/4 x 4” Hex Bolts Notice hole towards top (with lock washer, flat washer and 2383 t-nut).
  • Page 32 Step 14: Swing Wall Assembly Part 1 A: Loosely attach (2558) Ground Back using 2 (H4) 1/4 x 4” Hex Bolts (with lock washer, flat washer and t-nut) in the top holes, (2370) Floor Back using 2 (H8) 1/4 x 4-1/4” Hex Bolts (with lock washer, flat washer and t-nut) in the bottom holes and (2389) SW Back using 4 (H8) 1/4 x 4-1/4”...
  • Page 33 Step 14: Swing Wall Assembly Part 2 Note: Pre-drill all holes using a 1/8” drill bit before installing the Lag Screws. E: Make sure the assembly is square then attach (2370) Floor Back to each (2383) Post with 2 (LS3) 1/4 x 3” Lag Screw (with flat washer).
  • Page 34 Step 15: Floor Assembly Part 1 A: 5/8” down from the top of both (2371) Floor Ends attach (0790) Floor Joist with 2 (S4) #8 x 3” Wood Screws per end. (fig. 15.1 and 15.2) B: On the Swing Wall attach (0795) Side Joist to the inside of (2370) Floor Back with 2 (H3) 1/4 x 2-1/2” Hex Bolts (with lock washer, flat washer and t-nut) and 2 (S7) #12 x 2”...
  • Page 35 Step 15: Floor Assembly Part 2 F: Place 1 (1853) Cedar Gap Board at each end of the assembly. Then starting on the Access Wall side place 3 (1851) Cedar Floor Boards, 3 (2415) Cedar Floor Boards, 1 (2416) Cedar Gap Board so the gap in the board fits around (2366) Centre Post, 1 more (2415) Cedar Floor Board and 1 (2414) Cedar Floor Board.
  • Page 36 Step 16: Attach Ground Stakes MOVE FORT TO FINAL LOCATION. FINAL LOCATION MUST BE LEVEL GROUND. WARNING: To prevent tipping and avoid potential injury, stakes must be driven 10-1/2” into ground. Digging or driving stakes can be dangerous if you do not check first for underground wiring, cables or gas lines. A: Drive 2 (0318) Ground Stakes 10-1/2”...
  • Page 37 Step 17: Roof Frame Assembly Part 1 A: On the Cafe Wall place 1 (2384) Post Support tight to top of (2837) Side Arch at each (2383) Post. Each (2384) Post Support must be flush to the inside edge of the posts. Attach each (2384) Post Support to posts with 3 (S2) #8 x 1-1/2”...
  • Page 38 Step 17: Roof Frame Assembly Part 2 C: On the Access Wall place 1 (2557) MK Support tight to top of (2553) MK Board at each (2383) Post. Each (2557) MK Support must be flush to the inside edge of the posts. Attach each (2553) MK Support to posts with 1 (H2) 1/4 x 2”...
  • Page 39 Step 17: Roof Frame Assembly Part 3 E: On the Cafe Wall and Access Wall sides place 1 (0348) SL Ground tight to top of each (2384) Post Support and (2557) MK Support and flush to the outside edges of each (2364) Block. Attach to each (2364) Block with 4 (H2) 1/4 x 2”...
  • Page 40 Step 18: Attach Roof to Fort Part 1 A: Attach 1 (2420) Bottom Gable to each end of the Roof Assembly from Step 7 with 1 (S2) #8 x 1-1/2” Wood Screw and 1 (S4) #8 x 3” Wood Screw per corner. (fig. 18.1 and 18.2) B: Attach 2 Corner Braces to each (2420) Bottom Gable with 2 (S13) #6 x 5/8”...
  • Page 41 Step 18: Attach Roof to Fort Part 2 C: With two helpers place the Roof Assembly on the fort as shown in fig. 18.3. All four Corner Braces should sit on the outside face of each (0348) SL Ground. (fig. 18.3 and 18.4) D: Attach each Corner Brace to the (0348) SL Grounds with 1 (S13) #6 x 5/8”...
  • Page 42 Step 19: Attach Gable to Roof A: Along each (2394) Roof Support measure 8” up from the top of (2420) Bottom Gables then tight to the underside of the Roof, on each Roof Support Assembly, attach 2 (2419) Gable Sides, at the measured spot, to (2394) Roof Supports and (2420) Bottom Gable with 2 (S2) #8 x 1-1/2”...
  • Page 43 Step 20: Upper Swing Wall Assembly A: In between both (2383) Posts on Swing Wall side attach 7 (5265) Cedar Walls to (2370) Floor Back and (2389) SW Back using 4 (S2) #8 x 1-1/2” Wood Screws per board. Make sure the bottom of the boards are tight against the floor boards and the bevelled ends are at the top and facing out.
  • Page 44 Step 21: Attach Hand Grip Pre-drill all holes using a 3/16” drill bit before installing the Lag Screws A: On the Front Wall measure 1-1/2” up (2383) Post from the top of (2350) Front Floor on the Access Wall side then attach 1 Hand Grip with 2 (LS1) 1/4 x 1-1/2” Lag Screws (with flat washer). (fig. 21.1 and 21.2) Fig.
  • Page 45 Step 22: Upper Front Wall Assembly Part 1 A: On the Front Wall, tight to the floor boards, (2366) Centre Post and (2383) Post and 3/8” back from the outside face of (2383) Post and (2366) Centre Post attach 1 (2407) Wall Joist to each post with 3 (S3) #8 x 2-1/2”...
  • Page 46 Step 22: Upper Front Wall Assembly Part 2 B: Between (2366) Centre Post and (2383) Post and tight to the top of the floor boards attach 3 (2412) CE Siding to both (2407) Wall Joists with 2 (S0) #8 x 7/8” Truss Screws per board. Make sure there are no gaps between boards (fig.
  • Page 47 Step 23: Front Window Wall Assembly Part 1 A: On the Front Wall place 1 (2406) Wall Board tight to (2364) Block on Cafe Wall and tight to top of (2407) Wall Joist then attach to (2391) Top Front Back and (2559) Window Bottom with 4 (S1) #8 x 1-1/8” Wood Screws. (fig. 23.1) B: Tight to (2364) Block on the Access Wall and 2”...
  • Page 48 Step 23: Front Window Wall Assembly Part 2 D: Flush to the inside edge of each (2406) Wall Boards attach 1 (2409) Window Trim with 2 (S1) #8 x 1-1/8” Wood Screws per board. (fig. 23.2 and 23.3) E: Flush to the outside edge of each (0606) CE Access Board attach 1 (2409) Window Trim with 2 (S1) #8 x 1-1/8”...
  • Page 49 Step 24: Cafe Window Wall Assembly A: In the centre of the Cafe Wall opening measure 3” down from the top of (0348) SL Ground and attach 2 (0850) CE Wall Boards to (0348) SL Ground and (2387) Side Arch with 4 (S1) #8 x 1-1/8” Wood Screws per board. (fig. 24.1 and 24.2) B: Flush to the outside edge of each (0850) CE Wall Board attach 1 (2409) Window Trim with 2 (S1) #8 x 1-1/8”...
  • Page 50 Step 25: Lower Swing Wall Assembly Part 1 A: Tight to the top of (2558) Ground Back and flush to the outside edges of both (2383) Posts on the Swing Wall side attach 6 (2413) CE Siding to each post with 2 (S0) #8 x 7/8” Truss Screws per board, as shown in fig. 25.1 and 25.2.
  • Page 51 Step 25: Lower Swing Wall Assembly Part 2 C: From inside the assembly measure 1-1/4” down from the top of (2422) Lower Back then place 2 (1858) Short Wall Supports over the pilot holes of the (2413) CE Siding then attach to (2422) Lower Back and (2558) Ground Back with 4 (S1) #8 x 1-1/8”...
  • Page 52 Step 26: Lower Cafe Wall Assembly Part 1 A: Flush to the outside edge of (2383) Post and tight to the top of (0348) SL Ground attach (1808) Short Trim to (2383) Post with 3 (S2) #8 x 1-1/2” Wood Screws. (fig. 26.1 and 26.2) B: Tight to top of (0348) SL Ground and tight to (1808) Short Trim attach 6 (1852) CE Siding to both (2383) Posts with 2 (S0) #8 x 7/8”...
  • Page 53 Step 26: Lower Cafe Wall Assembly Part 2 D: Place (1868) Table Support flush to the angled edge of (0376) Table Top, as shown in fig. 26.3. The overhang should measure Fig. 26.4 3-3/8” on each side. Attach using 5 (S7) #12 x 2” Pan Screws. E: Place Table Top Assembly tight to the top of (1852) CE Siding, (1808) Short Trim and (1870) Trim Short.
  • Page 54 Step 26: Lower Cafe Wall Assembly Part 3 F: From inside the assembly tight to the bottom of (0376) Table Top place 2 (1858) Short Wall Supports over the pilot holes of the (1852) CE Siding then attach to (1868) Table Support and (0348) SL Ground with 4 (S1) #8 x 1-1/8”...
  • Page 55 Step 26: Lower Cafe Wall Assembly Part 4 Note: Pre-drill all holes using a 1/8” drill bit before installing the lag screws. H: Tight to the bottom of (2371) Floor End, place (2387) Side Arch flush to the outside edges of each (2383) Post then attach with 2 (LS1) 1/4 x 1-1/2”...
  • Page 56 Step 27: Bench Assembly Part 1 A: Attach (2560) Lower Bench flush to the top and outside edges of 1 (2496) Seat Block and 1 (2484) Bench Leg with 4 (S2) #8 x 1-1/2” Wood Screws, as shown in fig. 27.1. Fig.
  • Page 57 Step 27: Bench Assembly Part 2 Pre-drill all holes using a 1/8” drill bit before installing the Lag Screw. B: Attach (2491) Diagonal to (2558) Ground Back with 1 (H2) 1/4 x 2” Hex Bolt (with lock washer, flat washer and t-nut) and to (2383) Post with 1 (LS1) 1/4 x 1-1/2”...
  • Page 58 Step 27: Bench Assembly Part 3 D: Attach (2484) Bench Leg to (2554) Front Ground with 1 (H2) 1/4 x 2” Hex Bolt (with lock washer, flat washer and t-nut) and 1 (S2) #8 x 1-1/2” Wood Screw. (fig. 27.4) E: Attach (2496) Seat Block to (2491) Diagonal with 1 (H3) 1/4 x 2-1/2”...
  • Page 59 Step 27: Bench Assembly Part 4 Pre-drill all holes using a 1/8” drill bit before installing the Wood Screws. G: Place flat end of (2562) Bench Top tight to (2491) Diagonal and flush to the outside edge of each (2496) Seat Block, pre-drill with a 1/8”...
  • Page 60 Step 28: Attach Slide to Fort A: Place Slide in the opening of the Cafe Wall, centred between (2383) Posts. (fig. 28.1 and 28.2) B: Place 2 (0620) SL Braces tight to the underside of (1853) Cedar Gap Board and (2371) Floor End and centred between (0790) Floor Joist and each (2383) Post.
  • Page 61 Step 29: Lower Front Wall Assembly Part 1 A: On the Front Wall measure 20-3/8” up from (2554) Front Ground then place (5265) Cedar Wall flush to outside edge of (2383) Post at measured location. Attach (5265) Cedar Wall to (2383) Post and (2377) Lower Post with 4 (S2) #8 x 1-1/2”...
  • Page 62 Step 29: Lower Front Wall Assembly Part 2 B: Tight to the top of (2554) Front Ground and flush to the outside edge of (2383) Post evenly space and attach 6 (2556) CE Siding to (2383) Post and (2377) Lower Post with 2 (S0) #8 x 7/8” Truss Screws per board, as shown in fig.
  • Page 63 Step 29: Lower Front Wall Assembly Part 3 D: From inside the assembly flush to the bottom of (2554) Front Ground place 1 (2408) Wall Support centred over the pilot holes of the siding then attach to (2350) Front Floor and (2554) Front Ground with 4 (S1) #8 x 1-1/8”...
  • Page 64 Step 30: Attach Door to Fort Part 1 A: In the opening for the door between (2383) Post and (2377) Lower Post, measure 5/8” up from the top of (2554) Front Ground then attach the Door Hinges on the Door Assembly from Step 6 to (2383) Post with 3 (S13) #6 x 5/8”...
  • Page 65 Step 30: Attach Door to Fort Part 2 B: From inside the fort place (2107) Door Stop against (2377) Lower Post so there is a 1” overhang and the notched out opening is lined up with the Catch Plate then attach with 3 (S15) #8 x 1-3/4” Wood Screws. (fig. 30.4 and 30.5) C: In the notched out opening of (2107) Door Stop attach the Magnetic Catch using 2 (S18) #6 x 1”...
  • Page 66 Step 31: Attach Windows and Clock Part 1 A: On the outside of the assembly measure 3/4” down from the top of (2387) Side Arch and (2559) Window Bottom then place four 6-Pane Arch Top Windows in the window gaps on the Front and Cafe Walls and attach with 8 (S13) #6 x 5/8”...
  • Page 67 Step 31: Attach Windows and Clock Part 2 B: Place Clock Face on the Front Wall lining the hole in the clock to the hole in (2430) Clock Siding, making sure the clock is snug to the siding. Attach to (2430) Clock Siding and (2412) CE Siding with 4 (S2) #8 x 1-1/2” Wood Screws.
  • Page 68 Step 32: Attach Rock Wall to Fort A: Place Rock Wall Assembly from Step 2 centred on and flush to top of (2350) Front Floor. Attach (2555) Rock Rails to (2350) Front Floor using 4 (S15) #8 x 1-3/4” Wood Screws as shown in fig. 32.1, 32.2 and 32.3. B: Attach (0702) CE Wall Board to top of Rock Wall Assembly, flush to top of (0349) Rock Rails using 4 (S2) #8 x 1-1/2”...
  • Page 69 Step 33: Connect Monkey Bar Assembly to Fort Part 1 A: Attach 2 MB Hanger Brackets to (2553) MK Board with 2 (PB2) 1/4 x 1-1/4” Pan Bolt (with lock washer, flat washer and t-nut) per bracket as shown in fig. 33.1 and 33.2. B: Place each (1565) MK Rail Short of the Monkey Bar Assembly from Step 10 in each MB Hanger Bracket and attach with 1 (PB5) 1/4 x 2”...
  • Page 70 Step 33: Connect Monkey Bar Assembly to Fort Part 2 D: Drive 1 (0318) Ground Stake 10-1/2” into the ground at one (2382) MK Post on the inside of the assembly and attach with 2 (S3) #8 x 2-1/2” Wood Screws. (fig. 33.4 and 33.5) WARNING: To prevent tipping and avoid potential injury, stakes must be driven 10-1/2”...
  • Page 71 Step 34: Attach Swing Assembly to Fort A: Attach Swing Assembly from Step 5 to (2390) SW Mount with 1 (G5) 5/16 x 4-1/2” Hex Bolt (with lock washer, flat washer and t-nut) and 1 (G8) 5/16 x 2” Hex Bolt (with 2 flat washers and 1 lock nut) as shown in fig. 34.1 and 34.2.
  • Page 72 Step 35: Glider Assembly A: Attach 1 Glider End to the Glider Seat using 1 (Z) 5/16 x 6” Hex Bolt (with 2 flat washers and 1 lock nut). Repeat for the second Glider End. (fig. 35.1) B: Install 2 Glider Rope with Chains into each Glider End using 2 - 5/16” Flat Washers and 1 Lock Nut per rope. (fig.
  • Page 73 Step 36: Attach Glider and Swings If Bolt protrudes WARNING: beyond T-Nut Check entire play centre for bolts protruding beyond T-Nuts. Use Use an extra extra washers to eliminate this condition. Flat Washer A: Connect the assembled Glider to the Glider Hangers previously installed. (fig. 36.1) B: Attach 2 Belt Swings to the Bolt-Thru Swing Hangers.
  • Page 74 Final Step: Attach I.D. Plaque ATTACH THIS WARNING & I.D. PLAQUE TO A PROMINENT LOCATION ON YOUR PLAY EQUIPMENT! (Fort or Swing Post) This provides warnings concerning safety and important contact information. A Tracking Number is provided to allow you to get critical information or order replacement parts for this specific model Attach with (S13) #6 x 5/8”...
  • Page 75 NOTES...
  • Page 76 Would you recommend the purchase of our products to friends and family? Comments: MAIL TO: Fill out your registration card online at KidKraft https://prdregistration.kidkraft.com/ 4630 Olin Road Dallas, TX 75244 United States KidKraft would like to say Thank You for Attention: Customer Service your time and feedback.

This manual is also suitable for:

F23870