Fuji Electric FCX-AII-V5 series Instructions Manual And Service Instructions page 79

(DP)
8: OUTPUT MODE
XMTR:DP
OUT=LIN
< INC > < CHANGE >
CHNG
INC
8-1: MODE CHANGE
XMTR : DP
Menu 9
OUT=LIN
< INC > < ENT > < CL >
ENT CL
*1
<OUTPUT MODE
In case of OUT= SQR
CHANGE>
8-1: MODE CHANGE
XMTR:DP
OUT=SQR
CHNG OK? < ENT/CL >
CL
ENT
8-2: MODE WRITE
XMTR:DP
OUT=SQR
ENT
8-3: LOW CUT
XX XX
POINT= . %FLOW
MODE=
< CHANGE > < CL >
CHNG CL
(a)
8-4: POINT CHANGE
XX XX
. %FLOW
< ENT > < CL >
CL
ENT
8-4: POINT CHANGE
XX XX
. %FLOW
CHNG OK? < ENT/CL >
ENT CL
8-5: POINT WRITE
XX XX
. %FLOW
8-6: LOW CUT MODE
LINEAR
< CHANGE > < CL >
CL
CHNG
8-7: LOW CUT MODE
< 1 > LINEAR
< 2 > ZERO
< 1 > < 2 > <CL >
1 2 CL
8-7: MODE CHANGE
LINEAR
CHNG OK? < ENT/CL >
CL
ENT
8-8: MODE WRITE
LINEAR
TN5FCXA2V5h-E
(a)
GP, AP, LL (Liquid Level)
8 : OUTPUT MODE
XMTR:GP
OUT=LIN
< INC > < CHANGE >
1 INC CHNG
8-1: MODE CHANGE
XMTR : GP
OUT=LIN
< ENT > < CL >
2
CL
In case of OUT=LIN
8-1: MODE CHANGE
XMTR:DP
OUT=LIN
CHNG OK? < ENT/CL >
5 CL
ENT
8-2: MODE WRITE
XMTR:DP
OUT=LIN
6
= LINEAR or ZERO
7
*2
*1 < INC > < DEC > Available Mode
8
1 OUT=LIN
2 OUT=SQR
Note) GP, AP, LL : OUT = LIN only
9
*2 0.00% Cut Point 20.00% FLOW
10
8-6: LOW CUT MODE
ZERO
< CHANGE > < CL >
11
CHNG CL
13
8-7: MODE CHANGE
ZERO
CHNG OK? < ENT/CL >
14 ENT CL
8-8: MODE WRITE
ZERO
15
Menu 8 : Output Mode
The output mode is used to select the proportional
mode (proportional to input differential pressure)
or square root extraction mode (proportinal to
differential pressure transmitter only.
1
8-1 Change the output mode
In case of square root extraction mode, the cut
point and the mode below the cut point can be
set.
• Under display
selection of the square root extraction mode
3
("SQR") or linear mode ("LIN").
8-3 Low cut point setting
4
The square root extraction mode is selected,
the display
should be set..
Note that if the cut point is set to a small value
around 0%, even a minute differential pressure
cut point is used for improving the measurement
There are two modes :
Output
Low cut
point
12
Fig. A: With linear output
selected in low cut mode
• On display
16
cut mode
• Under display
17
table for output below the cut point.
, press <INC
is presented and the low cut point
Output
Low cut
point
Differential
Differential
input
Fig. B: With zero output
selected in low cut mode
, press "CHANGE" to set the low
, linear or zero output is selec-
DEC
input
77