Danfoss VLT AutomationDrive FC 300 Design Manual page 72

FC 300 Selection
High/Normal Load*
Typical Shaft output at 550 V
[kW]
Typical Shaft output at 575 V
[hp]
Typical Shaft output at 690 V
[kW]
4 4
Enclosure IP21, IP55
Output current
Continuous (3x525-550 V) [A]
Intermittent (60 s overload)
(3x525-550 V) [A]
Continuous (3x551-690 V) [A]
Intermittent (60 s overload)
(3x551-690 V) [A]
Continuous KVA (at 550 V) [KVA]
Continuous KVA (at 575 V) [KVA]
Continuous KVA (at 690 V) [KVA]
Max. input current
Continuous (at 550 V) [A]
Continuous (at 575 V) [A]
Additional specifications
Max. cable cross section (mains
and motor) [mm
Max. cable cross section (load
share and brake) [mm
Max cable size with mains
disconnect [mm
Estimated power loss
at rated max. load [W]
Weight, enclosure IP21, IP55 [kg]
Efficiency 4)
Table 4.12 C2 Frame,
Mains Supply 3x525-690 V AC IP21/IP55 - NEMA 1/NEMA 12 (FC 302 only)
70
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-21462-Danfoss-131B8966-VLT-Automation-VT-Drive-VFD-FC301-230V-5-HP.aspx
P30K
HO
22
30
30
C2
36
54
34
51
34.3
33.9
40.6
36
54
2 (AWG)]
2
(AWG)]
2 (AWG)] 2)
480
4)
0.98
MG33BE02 - VLT
®
VLT AutomationDrive FC 300 Design Guide, 0.25-75 kW
P37K
NO HO NO
30 30 37
40 40 50
37 37 45
C2
43 43 54
47.3 64.5 59.4
41 41 52
45.1 61.5 57.2
41.0 41.0 51.4 51.4
40.8 40.8 51.8 51.8
49.0 49.0 62.1 62.1
49 49 59
53.9 72 64.9
150 (300 MCM)
95, 70, 70
(3/0, 2/0, 2/0)
592
0.98
®
is a registered Danfoss trademark
P45K P55K
HO NO HO NO
37 45 45 55
50 60 60 75
45 55 55 75
C2 C2
54 65 65 87
81 71.5 97.5 95.7
52 62 62 83
78 68.2 93 91.3
61.9 61.9 82.9
61.7 61.7 82.7
74.1 74.1 99.2
59 71 71 87
87 78.1 105 95.7
95 (3/0)
185, 150, 120
(350 MCM, 300
MCM, 4/0)
720 880
65
0.98 0.98
P75K
HO NO
55 75
75 100
75 90
C2
87 105
130.5 115.5
83 100
124.5 110
82.9 100.0
82.7 99.6
99.2 119.5
87 99
129 108.9
-
1200
0.98