Advertisement
Setting Functions (continued)
3
Turn
Host number
(DoCoMo) : The Host number is set to the
ドコモ
User defined
4
Press
The Host number is set.
Check
• If you set [Host] during i-mode operations, a
warning sound is emitted and the message
"Cannot set during i-mode" appears.
• When the Host is changed, you cannot use i-mode.
Hint
• If the Host is already registered, the index of the
Host registered to [User defined] is displayed.
• The Host number of
depending on the area of subscription. The areas
are "DoCoMo Hokkaido", "DoCoMo Tohoku",
"DoCoMo", "DoCoMo Tokai", "DoCoMo
Hokuriku", "DoCoMo Kansai", "DoCoMo
Chugoku", "DoCoMo Shikoku", "DoCoMo
Kyushu".
Setting the favorite host
number
1
Press
and select [Settings] / [Common
setting] / [Host] / [Host selection]
2
Enter your PIN
342
to select the
Ｈｏｓｔ ｓｅｌｅｃｔｉｏｎ
ドコモ
Ｕｓｅｒ ｄｅｆｉｎｅｄ
ｃａｎｃｅｌ
ｓｅｌｅｃｔ
i-mode center in your area.
: The i-mode is connected to the
phone number you specify.
(
)
ｓｅｌｅｃｔ
Ｈｏｓｔ
Ｈｏｓｔ ｓｅｌｅｃｔｉｏｎ
Ｒｅｓｅｔ ｈｏｓｔｓ
Ｈｏｓｔ ｓｅｌｅｃｔｅｄ
(DoCoMo) differs
ドコモ
(
) at the standby screen
ｉ−ｍｏｄｅ
s
P.72
3
Turn
to select [User defined]
and press
(
4
Set each item
P.56
<Index>
Enter the name of the destination.
You can enter up to 8 two-byte/16 one-byte
characters.
<Host number>
Enter the phone number of the destination.
s
P.86
You can enter up to 11 digits.
<Host address>
Enter the name of [Host].
You can enter up to 30 one-byte characters.
5
Press
(
ｃｍｐｌｔ
The Host number you
enter is set.
Check
• When setting Host number, if all of [Index], [Host
number], and [Host address] are not filled in, a
warning sound is emitted and the message
"Setting is incomplete. Item is missing" appears.
• The Host number of [
ドコモ
and cannot be changed.
Hint
• After selecting [User defined] in step 3, you can
also display the screen of the Host number entry
by pressing
(
).
ｅｄｉｔ
)
ｓｅｌｅｃｔ
s
Ｈｏｓｔ ｎｕｍｂｅｒ
＜Ｉｎｄｅｘ＞
Ｈｏｓｔ Ａ
＜Ｈｏｓｔ ｎｕｍｂｅｒ＞
＃１２３４
＜Ｈｏｓｔ ａｄｄｒｅｓｓ＞
ｘｘｘｘｘ．ｎｅ．ｊｐ
ｃａｎｃｅｌ
ｃｍｐｌｔ
ｓｅｌｅｃｔ
s
P.73
s
P.73
)
Ｈｏｓｔ ｓｅｌｅｃｔｉｏｎ
ドコモ
Ｕｓｅｒ ｄｅｆｉｎｅｄ
Ｈｏｓｔ ｓａｖｅｄ
] (DoCoMo) is fixed
Advertisement
