Index - Mitsubishi Electric A800 Plus Series Function Manual

Index

10.6
Index
A
Acceleration/deceleration time selection for line speed command
(X105 signal, X106 signal) ..................................................69, 188
Acceleration/deceleration time setting for line speed command .69
Actual line speed (monitoring)...................................................181
Actual line speed detection signal .....................................163, 188
Analog input signals and pulse train input signals.......................43
Analog output signal for dancer tension control (monitoring) ....181
Analog output signal function for dancer tension control.............92
Average current load detection .....................................................7
B
Break detection (Y231 signal) .............................74, 108, 150, 191
D
Dancer compensation speed (monitoring) ................................181
Dancer position / tension feedback detection
(Y235 signal) ...............................................................73, 107, 191
Dancer roll position detection signal..........................................188
Dancer roll target position signal .........................................71, 188
Dancer signal input selection ......................................................71
I
Inertia compensation .................................................................130
Inertia compensation (monitoring).............................................181
Inertia compensation acceleration (X111 signal) ......................130
Inertia compensation deceleration (X112 signal) ......................130
Inertia compensation second acceleration/deceleration time
(X113 signal) .............................................................................130
Initial winding diameter calculation at a start (dancer feedback
speed control)............................................................................171
Initial winding diameter calculation at a start (tension sensorless
torque control) ...........................................................................175
Input signal list...........................................................................188
Integral term activation selection (X103 signal)...................85, 188
L
Line speed acceleration (Y237 signal) ......................................130
Line speed at winding diameter calculated value activation......167
Line speed command ..........................................................60, 188
Line speed command (monitoring)............................................181
Line speed command input .........................................................60
Line speed command input (compensation) ...............................66
Line speed command input by analog input................................60
Line speed deceleration (Y238 signal) ......................................130
Line speed pulse (monitoring) ...................................................181
M
Measured winding diameter input (X122 signal) .......................175
Mechanical loss compensation .................................................135
Mechanical loss compensation (monitoring) .............................181
Mechanical loss compensation function....................................135
Minimum/maximum winding diameter selection
(X107 signal, X108 signal) ........................................166, 169, 188
Monitor list .................................................................................181
O
Offset displacement storage (X102 signal) .................73, 108, 188
238
APPENDIX
Operation command source and speed command source
(Pr.338, 339) .............................................................................193
Output signal list........................................................................191
P
PID action selection (Pr.128)...............................................58, 148
PID compensation disabled (X116 signal) ..................58, 148, 188
PID gain switchover (X120 signal, X121 signal)..................86, 188
PID integral term reset input (X100 signal) .................................85
PID lower limit (FDN signal) ................................74, 108, 150, 191
PID offset displacement ......................................................73, 108
PID torque control actual tension ..............................................181
PID torque control manipulated tension ....................................181
PID upper limit (FUP signal)................................74, 108, 150, 191
R
Reel change (X104 signal) ..........................................................90
S
SND rating.....................................................................................7
Speed control proportional gain disabled
(X124 signal) .....................................................................179, 188
Speed control proportional gain selection according to the winding
diameter calculation result.........................................................179
Stall mode function....................................................................137
Stall mode trigger (X123 signal) ................................................137
Stored winding diameter clear (X109 signal).....................176, 188
T
Taper function ...........................................................................124
Target winding diameter achieved (Y233 signal) ..............171, 191
Tension control selection (X114 signal) ......58, 117, 148, 158, 188
Tension PI gain tuning.................................................................76
Tension sensor feedback torque control function selection ......148
Terminal 1 input voltage (monitoring) ........................................181
W
Winding diameter (monitoring) ..................................................181
Winding diameter calculation and winding diameter compensation
function......................................................................................158
Winding diameter calculation completion
(Y232 signal) .............................................................171, 175, 191
Winding diameter calculation completion signal................171, 175
Winding diameter calculation using actual line speed (actual line
speed method) ..........................................................................163
Winding diameter compensation selection (X115 signal)..161, 188
Winding diameter compensation speed (monitoring) ................181
Winding diameter compensation torque command
(monitoring) ...............................................................................181
Winding length (monitoring) ......................................................181
Winding length clear (X117 signal)....................................176, 188
Winding/unwinding shaft selection ......................................59, 149