Mitsubishi Electric A800 Plus Series Function Manual page 36

Pr.
Pr.
group
D304 24
Multi-speed setting (4 speed to 7
to to
speed)
D307 27
D308 232
Multi-speed setting (8 speed to 15
to to
speed)
D315 239
Tension / Torque command
D400 804
source selection
D401 805
Torque command value (RAM)
Torque command value
D402 806
(RAM,EEPROM)
Torque command reverse
D403 1114
selection
H: Protective function parameters
Parameters to protect the motor and the inverter.
Pr.
Pr.
group
H000 9
Electronic thermal O/L relay
First free thermal reduction
H001 600
frequency 1
First free thermal reduction ratio
H002 601
1
First free thermal reduction
H003 602
frequency 2
First free thermal reduction ratio
H004 603
2
First free thermal reduction
H005 604
frequency 3
H006 607
Motor permissible load level
Second electronic thermal O/L
H010 51
relay
Second free thermal reduction
H011 692
frequency 1
Second free thermal reduction
H012 693
ratio 1
Second free thermal reduction
H013 694
frequency 2
Second free thermal reduction
H014 695
ratio 2
Second free thermal reduction
H015 696
frequency 3
Second motor permissible load
H016 608
level
H020 561
PTC thermistor protection level
PTC thermistor protection
H021 1016
detection time
876
H022
Thermal protector input
∗1
H030 875
Fault definition
H100 244
Cooling fan operation selection
Earth (ground) fault detection at
H101 249
start
H102 598
Undervoltage level
H103 997
Fault initiation
Output phase loss protection
H200 251
selection
Input phase loss protection
H201 872
selection
H300 65
Retry selection
Number of retries at fault
H301 67
occurrence
H302 68
Retry waiting time
Refer
Name to
page
─
∗6
─
∗6
118
─
∗6
─
∗6
121
Refer
Name to
page
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
Parameter list (by function group)
Pr.
Pr.
group
H303 69
Retry count display erase
H400 1
Maximum frequency
H401 2
Minimum frequency
H402 18
High speed maximum frequency
H410 807
Speed limit selection
Forward rotation speed limit/
H411 808
speed limit
Reverse rotation speed limit/
H412 809
reverse-side speed limit
H414 1113
Speed limit method selection
873
H415
Speed limit
∗1
Speed deviation excess detection
H416 285
frequency
853
H417
Speed deviation time
∗1
H420 31
Frequency jump 1A
H421 32
Frequency jump 1B
H422 33
Frequency jump 2A
H423 34
Frequency jump 2B
H424 35
Frequency jump 3A
H425 36
Frequency jump 3B
H429 552
Frequency jump range
Stall prevention operation level
H500 22
(Torque limit level)
Stall prevention operation
H501 156
selection
Load characteristics
H520 1480
measurement mode
Load characteristics load
H521 1481
reference 1
Load characteristics load
H522 1482
reference 2
Load characteristics load
H523 1483
reference 3
Load characteristics load
H524 1484
reference 4
Load characteristics load
H525 1485
reference 5
Load characteristics maximum
H526 1486
frequency
Load characteristics minimum
H527 1487
frequency
Upper limit warning detection
H531 1488
width
Lower limit warning detection
H532 1489
width
H533 1490
Upper limit fault detection width
H534 1491
Lower limit fault detection width
Load status detection signal
H535 1492
delay time / load reference
measurement waiting time
Second stall prevention operation
H600 48
level
Second stall prevention operation
H601 49
frequency
Third stall prevention operation
H602 114
level
Third stall prevention operation
H603 115
frequency
Stall prevention operation level
H610 23
compensation factor at double
speed
Stall prevention operation
H611 66
reduction starting frequency
PARAMETER LIST
Refer
Name to
page
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
35
2