Mitsubishi Electric A800 Plus Series Function Manual page 20

Pr.
Pr. Name
group
475 R124 Third PID differential time
Third PID proportional band for
476 R125
values below set point
Third PID integral time for
477 R126
values below set point
Third PID differential time for
478 R127
values below set point
479 R128 Fourth PID proportional band
480 R129 Fourth PID integral time
481 R130 Fourth PID differential time
Fourth PID proportional band for
482 R131
values below set point
Fourth PID integral time for
483 R132
values below set point
Fourth PID differential time for
484 R133
values below set point
485 R149 Integral control activation
486 R140 Deviation A
487 R141 Deviation B
488 R142 Deviation C1
489 R143 Deviation C2
490 R144 PID gain A
491 R145 PID gain B
492 R146 PID gain C1
493 R147 PID gain C2
494 R148 PID gain D
495 M500 Remote output selection
496 M501 Remote output data 1
497 M502 Remote output data 2
PLC function flash memory
498 A804
clear
Stop mode selection at
502 N013
communication error
503 E710 Maintenance timer 1
Maintenance timer 1 warning
504 E711
output set time
505 M001 Speed setting reference
S-pattern time at a start of
516 F400
acceleration
S-pattern time at a completion of
517 F401
acceleration
S-pattern time at a start of
518 F402
deceleration
S-pattern time at a completion of
519 F403
deceleration
MODBUS RTU communication
539 N002
check time interval
USB communication station
547 N040
number
USB communication check time
548 N041
interval
549 N000 Protocol selection
NET mode operation command
550 D012
source selection
PU mode operation command
551 D013
source selection
552 H429 Frequency jump range
553 A603 PID deviation limit
554 A604 PID signal operation selection
555 E720 Current average time
556 E721 Data output mask time
Current average value monitor
557 E722
signal output reference current
560 A712 Second frequency search gain
561 H020 PTC thermistor protection level
Parameter list (by parameter number)
Minimum
Setting range setting
increments
0.01 to 10 s, 9999 0.01 s
0.1 to 1000%, 9999 0.1%
0.1 to 3600 s, 9999 0.1 s
0.01 to 10 s, 9999 0.01 s
0.1 to 1000%, 9999 0.1%
0.1 to 3600 s, 9999 0.1 s
0.01 to 10 s, 9999 0.01 s
0.1 to 1000%, 9999 0.1%
0.1 to 3600 s, 9999 0.1 s
0.01 to 10 s, 9999 0.01 s
0 to 3 1
400.1 to 600% 0.1%
400 to 599.9% 0.1%
400.1 to 599.9%, 9999 0.1%
400.1 to 599.9%, 9999 0.1%
0.1 to 1000%, 9999 0.1%
0.1 to 1000%, 9999 0.1%
0.1 to 1000%, 9999 0.1%
0.1 to 1000%, 9999 0.1%
0.1 to 1000%, 9999 0.1%
0, 1, 10, 11 1
0 to 4095 1
0 to 4095 1
0, 9696 (0 to 9999) 1
0 to 2, 11, 12 1
0 (1 to 9998) 1
0 to 9998, 9999 1
1 to 590 Hz 0.01 Hz
0.1 to 2.5 s 0.1 s
0.1 to 2.5 s 0.1 s
0.1 to 2.5 s 0.1 s
0.1 to 2.5 s 0.1 s
0 to 999.8 s, 9999 0.1 s
0 to 31 1
0 to 999.8 s, 9999 0.1 s
0, 1 1
0, 1, 9999 1
1 to 3, 9999 1
0 to 30 Hz, 9999 0.01 Hz
0.0 to 100.0%, 9999 0.1%
0 to 3 1
0.1 to 1 s 0.1 s
0 to 20 s 0.1 s
0 to 500 A 0.01 A
∗2
0 to 3600 A 0.1 A
∗3
0 to 32767, 9999 1
0.5 to 30 kΩ, 9999 0.01 kΩ
Initial value Refer
to
FM CA
page
9999 86
9999 86
9999 86
9999 86
9999 86
9999 86
9999 86
9999 86
9999 86
9999 86
0 85
600% 86
400% 86
9999 86
9999 86
9999 86
9999 86
9999 86
9999 86
9999 86
0 ─
∗17
0 ─
∗17
0 ─
∗17
0 ─
∗17
0 ─
∗17
0 ─
∗17
9999 ─
∗17
60 Hz 50 Hz ─
∗17
0.1 s ─
∗17
0.1 s ─
∗17
0.1 s ─
∗17
0.1 s ─
∗17
9999 ─
∗17
0 ─
∗17
9999 ─
∗17
0 ─
∗17
9999 ─
∗17
9999 ─
∗17
9999 ─
∗17
9999 ─
∗17
0 76
1 s ─
∗17
0 s ─
∗17
Inverter rated
∗2
─
∗17
current
∗3
9999 ─
∗17
9999 ─
∗17
PARAMETER LIST
Customer
setting
2
19