YASKAWA U1000 Series Technical Manual page 491

No.(Addr.) Name
F1-51
PGoH Detection Level
(3D3H)
F1-52 Communication Speed of Serial
(3D4H) Encoder Selection
<10> Default setting is determined by the control mode (A1-02).
<45> Regional default settings
Setting 600 ppr: Japan (Model code: CIMR-UA), India (Model code: CIMR-UD), and Asia (Model code: CIMR-UT)
Setting 1024 ppr: China (Model code: CIMR-UB)
F2: Analog Input Card Settings (AI-A3)
■
No.(Addr.) Name
F2-01 Analog Input Option Card
(38FH) Operation Selection
F2-02
(368H)
Analog Input Option Card Gain
F2-03
(369H)
Analog Input Option Card Bias
F3: Digital Input Card Settings (DI-A3)
■
No.(Addr.) Name
F3-01 Digital Input Option Card Input
(390H) Selection
F3-03 Digital Input Option DI-A3 Data
(3B9H) Length Selection
F4: Analog Monitor Card Settings (AO-A3)
■
No.(Addr.) Name
F4-01
Terminal V1 Monitor Selection
(391H)
F4-02
(392H)
Terminal V1 Monitor Gain
F4-03
Terminal V2 Monitor Selection
(393H)
F4-04
(394H)
Terminal V2 Monitor Gain
YASKAWA ELECTRIC SIEP C710636 02B YASKAWA U1000 Technical Manual
V/f V/f w/PG
OLV/PM AOLV/PM
Sets the level for detecting PG Hardware Fault (PGoH). Available when F1-20 = 1
V/f V/f w/PG
OLV/PM AOLV/PM
Selects the communication speed between the PG-F3 option and serial encoder.
0: 1M bps/9600 bps (EnDat 2.2/22 / Hiperface)
1: 500k bps/19200 bps (EnDat 2.2/22 / Hiperface)
2: 1M bps/38400 bps (EnDat 2.2/22 / Hiperface)
3: 1M bps/38400 bps (EnDat 2.2/22 / Hiperface)
All Modes
0: Option card input terminals V1, V2, and V3 replace drive input terminals A1, A2, and A3.
1: Input signals to terminals V1, V2, and V3 are added together to create the frequency
reference.
All Modes
Sets the gain for the input signal to the analog card.
All Modes
Sets the bias for the input signal to the analog card.
All Modes
0: BCD, 1% units
1: BCD, 0.1% units
2: BCD, 0.01% units
3: BCD, 1 Hz units
4: BCD, 0.1 Hz units
5: BCD, 0.01 Hz units
6: BCD customized setting (5 digit), 0.02 Hz units
7: Binary input
The unit and the setting range are determined by F3-03.
F3-03 = 0: 255/100% (-255 to +255)
F3-03 = 1: 40961/100% (-4095 to +4095)
F3-03 = 2: 30000/100% (-33000 to +33000)
When the digital operator units are set to be displayed in Hertz or user-set units (o1-03 = 2 or 3),
the units for F3-01 are determined by parameter o1-03.
All Modes
0: 8 bit
1: 12 bit
2: 16 bit
All Modes
Sets the monitor signal for output from terminal V1. Set this parameter to the last three digits of
the desired U- monitor. Some U parameters are available only in certain control modes.
All Modes
Sets the gain for voltage output via terminal V1.
All Modes
Sets the monitor signal for output from terminal V2. Set this parameter to the last three digits of
the desired U- monitor. Some U parameters are available only in certain control modes.
All Modes
Sets the gain for voltage output via terminal V2.
Description
OLV CLV
CLV/PM
OLV CLV
CLV/PM
Description
Description
Description
B.3 Parameter Table
Setting Page
Default: 80%
Min: 1% 260
Max: 100%
Default: 0
Min: 0 260
Max: 3
Setting Page
Default: 0
Min: 0 260
Max: 1
Default: 100.0%
Min: -999.9% 261
Max: 999.9%
Default: 0.0%
Min: -999.9% 261
Max: 999.9%
Setting Page
Default: 0
Min: 0 261
Max: 7
Default: 2
Min: 0 261
Max: 2
Setting Page
Default: 102
Min: 000 261
Max: 999
Default: 100.0%
Min: -999.9% 262
Max: 999.9%
Default: 103
Min: 000 261
Max: 999
Default: 50.0%
Min: -999.9% 262
Max: 999.9%
491
B