IAI GO-2400M-PMCL User Manual page 90

BINNING_GAIN_EN R/W
PIrisLensControl R/W
PirisLensSelect R/W
PIrisStepMax R/O
PIrisPosition R/W
PirisAutoMin R/W
PirisAutoMax R/W
PirisCurrentFvalue R/O
PirisAutoStepMin R/W
BGOE 0: Off / 1: On
PLC 0: Off / 1: On
PLS 0: Others
1: LM16JC5MM
2: LM35JC5MM
3: CINEGON1.9/10
4: CINEGON1.8/4.8
5: SCHNEIDER
COMPACTIRIS
6: MG3518KC
7: VV1618HF_DN_P
PIS Indicate P-IRIS
control step
maximum value
PIP Min to Max
PLI 0: FULL OPEN
1: F1.4
2: F2
3: F2.8
4: F4
5: F5.6
6: F8
7: F11
8: F16
9: F22
10: F32
11: CLOSE
PLA Same as above.
PCV Same as above.
PLSI Min to Max
0 1 0
0 1 0
0 8 1
0 200 128
0 200 128
0 11 1
0 11 5
0 11 0
0 200 0
̶ 90 ̶
GO-2400M-PMCL / GO-2400C-PMCL
BGOE =[Param.]<CR><LF> Set whether to
BGOE?<CR><LF> apply gain to the
image during
binning mode.
PLC =[Param.]<CR><LF> Set this to [On]
PLC?<CR><LF> when using a
(GO-2400-AUX1(P-Iris) only) P-Iris lens.
PLS=[Param.]<CR><LF> Select the P-Iris
PLS?<CR><LF> lens to be used.
(GO-2400-AUX1(P-Iris) only)
PIS?<CR><LF> Display the
Different depending on maximum step
PirisLensSelect value number for the
(P-Iris Model only) P-Iris lens
selected in [P-IRIS
Lens Select].
(This is only
enabled when
[P-IRIS Lens
Select] is set to a
setting other than
[OTHERS].)
PIP=[Param.]<CR><LF> Set the iris
PIP?<CR><LF> position of the
Maximum value is P-Iris lens as a
PIrisStepMax step number.
(GO-2400-AUX1(P-Iris) only)
PLI=[Param.]<CR><LF> Set the minimum
PLI?<CR><LF> value for the
Minimum value and control range as
Maximum value are different an F number
depending on when controlling
PirisLensSelect value the P-Iris lens
(GO-2400-AUX1(P-Iris) only) using auto iris.
(This is only
enabled when
[P-IRIS Lens
Select] is set to a
setting other than
[OTHERS].)
PLI=[Param.]<CR><LF> Set the maximum
PLI?<CR><LF> value for the
Minimum value and control range as
Maximum value are different an F number
depending on when controlling
PirisLensSelect value(GO- the P-Iris lens
2400-AUX1(P-Iris) only) using auto iris.
(This is only
enabled when
[P-IRIS Lens
Select] is set to a
setting other than
[OTHERS].)
PCV?<CR><LF> Display the iris
(GO-2400-AUX1(P-Iris) position of the
only) P-Iris lens as an F
number.
PLSI=[Param.]<CR><LF> Set the minimum
PLSI?<CR><LF> value for the
(GO-2400-AUX1(P-Iris) only) control range as a
step number
when controlling
the P-Iris lens
using auto iris.
(This is only
enabled when
[P-IRIS Lens
Select] is set to
[OTHERS].)