IAI GO-2400M-PMCL User Manual page 88

GpioPulseGenLength0 R/W
GpioPulseGenStart R/W
Point0
GpioPulseGenEnd R/W
Point0
GpioPulseGenRepeat R/W
Count0
GpioPulseGenClear R/W
Mode0
GpioPulseGenSync R/W
Mode0
GpioPulseGenInput0 R/W
GpioPulseGen Invert0 R/W
GpioNand0 R/W
InputSource1
GpioNand0 R/W
InputSource2
PGL0 Min to Max
PGST0 Min to Max
PGEN0 Min to Max
PGRPT0 Min to Max
PGCM0 0: Free Run
1: Level High
2: Level Low
3: Rising Edge
4: Falling Edge
PGSM0 0: Async Mode
1: Sync Mode
PGIN0 0: Low
1: High
4: FrameTriggerWait
5: FrameActive
6: ExposureActive
7: FVAL
8: LVAL
10: UserOutput0
11: UserOutput1
12: TTL_In1(Std Only)
13: CL_CC1_In
15: nand0
16: nand1
PGINV0 0:Non-Inv
1:Inv
ND0IN1 0: Low
1: High
3: FrameTriggerWait
4: FrameActive
5: ExposureActive
6: Fval
7: Lval
8: PulseGenerator0
10: UserOutput0
11: UserOutput1
12: TTL_In1(Std Only)
13: CL_CC1_In
14: Nand0
ND0IN2 Same as above.
1 1048575 1
0 1048574 0
1 1048575 1
0 255 0
0 4 0
0 1 0
0 16 0
0 1 0
0 6 0
0 6 0
̶ 88 ̶
GO-2400M-PMCL / GO-2400C-PMCL
PGL0=[Param.]<CR><LF> Set the maximum
PGL0?<CR><LF> count up value
using clock value.
PGST0=[Param.]<CR><LF> Set the start point
PGST0?<CR><LF> for the High
interval using
clock value.
When the counter
reaches this value,
the output
becomes 1.
PGEN0=[Param.]<CR><LF> Set the start point
PGEN0?<CR><LF> for the Low interval
using clock value.
When the counter
reaches this value,
the output
becomes 0.
PGRPT0=[Param.]<CR><LF> Set the repeat
PGRPT0?<CR><LF> count for the
counter.
When this is set to
0, the counter will
be free-running
with limitless
repeating.
PGCM0=[Param.]<CR><LF> Set the clear
PGCM0?<CR><LF> signal condition
for the count clear
input of the pulse
generator.
PGSM0=[Param.]<CR><LF> Select the sync
PGSM0?<CR><LF> mode for the
count clear input
signal.
PGIN0=[Param.]<CR><LF> Select the count
PGIN0?<CR><LF> clear input signal
source.
PGINV0=[Param.]<CR><LF> Select whether to
PGINV0?<CR><LF> invert the polarity
of the count clear
input signal.
ND0IN1=[Param.]<CR><LF> Select the input
ND0IN1?<CR><LF> source signal for
NAND0 In1.
ND0IN2=[Param.]<CR><LF> Select the input
ND0IN2?<CR><LF> source signal for
NAND0 In2.