IAI GO-2400M-PMCL User Manual page 71

PixelFormat R/(W)
TestImageSelector R/W
SensorDigitizationTaps R/W
5. Acquisition Control
FrameStartTrigMode R/W
TriggerSoftware (R)/W
FrameStartTrigSource R/W
FrameStartTrig R/W
Activation
ExposureMode R/W
ExposureTimeRaw R/W
ExposureAuto R/W
6. Digital I/O Control
LineInverter_Nand0In1 R/W
LineInverter_Nand0In2 R/W
LineInverter_Nand1In1 R/W
BA Mono model:
0: Mono8
1: Mono10
2: Mono12*
Color model:
0: ColorRG8
1: ColorRG10
2: ColorRG12*
(*VP bypass On
only)
TPN 0: Off
1: GreyHorizontalRamp
2: GreyVerticalRamp
3: GreyHorizontalRampMoving
4: Horizontal Colorbar*
5: Vertical Colorbar*
6: Moving Colorbar*
(* Color model only)
SDT 1: 10-bit
2: 12-bit
TM Off/On
STRG 0 or 1
TI 0: Low
1: High
2: SoftTrigger
8: PulseGenerator0
10:UserOutput0
11:UserOutput1
12: TTL_In1(Std Only)
13: CL_CC1_In
14: Nand0
15: Nand1
TA 0: RisingEdge
1: FallingEdge
2: LevelHigh
3: LevelLow
EM 0: Off
1: Timed
2: TriggerWidth
PE Min to Max[us]
ASC 0: Off
1: Continuous
ND0INV1 False/True
ND0INV2 False/True
ND1INV1 False/True
0 2 0
0 Mono:3 0
Color:6
1 2 2
0 1 0
— — —
0 15 0
0 3 0
0 2 0
15 * 8000000 18000
1
0 1 0
0 1 0
0 1 0
0 1 0
̶ 71 ̶
GO-2400M-PMCL / GO-2400C-PMCL
BA=[Param.]<CR><LF> Set the pixel
BA?<CR><LF> format.
TPN=[Param.]<CR><LF> Select the test
TPN?<CR><LF> image.
SDT=[Param.]<CR><LF> Displays the
SDT?<CR><LF> digital tones
output from the
sensor.
TM=[Param.]<CR><LF> Display the
TM?<CR><LF> Trigger mode.
STRG=0<CR><LF> Execute a
software trigger.
TI=[Param.]<CR><LF> Select the trigger
TM?<CR><LF> signal source.
TA=[Param.]<CR><LF> Select the polarity
TA?<CR><LF> of the trigger
signal (i.e.,
location of signal
at which trigger is
applied).
EM=[Param.]<CR><LF> Select the
EM?<CR><LF> exposure mode.
PE=[Param.]<CR><LF> Set the exposure
PE?<CR><LF> time.
The maximum
value varies
depending on the
[Acquisition
Frame Rate Raw]
value.
ASC=[Param.]<CR><LF> Set whether to
ASC?<CR><LF> enable auto
exposure.
ND0INV1=[Param.]<CR><LF> Enable/disable
ND0INV1?<CR><LF> polarity inversion
for the NAND0 In1
input.
ND0INV2=[Param.]<CR><LF> Enable/disable
ND0INV2?<CR><LF> polarity inversion
for the NAND0 In2
input.
ND1INV1=[Param.]<CR><LF> Enable/disable
ND0INV1?<CR><LF> polarity inversion
for the NAND1 In1
input.